Philips HR7761 User Manual

Register your product and get support at
www.philips.com/welcome
User manual
EN
ZH-TW 使用手冊
KO
사용 설명서
Manual pengguna
MS-MY
ZH-CN
用户手册
Specifications are subject to change without notice
© 2012 Koninklijke Philips Electronics N.V.
All rights reserved.
HR7761_7762_7763_ ROW_UM_V1.3
English
1 Important
Read this user manual carefully before you use the appliance, and save the user manual for
future reference.
Danger
• Do not immerse the motor unit in water nor rinse it under the tap.
Warning
• Never use your fingers or an object (for example, a spatula) to push ingredients into
the feeding tube while the appliance is running. Only use the pusher.
• Before you connect the appliance to the power, make sure that the voltage indicated
on the bottom of the appliance corresponds to the local power voltage.
• Never connect this appliance to a timer switch, to avoid a hazardous situation.
• If the power cord, the plug, or other parts are damaged, do not use the appliance.
• If the power cord is damaged, you must have it replaced by Philips, a service center
authorized by Philips, or similarly qualified persons to avoid a hazard.
• This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning use of the appliance by a
person responsible for their safety.
• For their safety, do not allow children to play with the appliance.
• Never let the appliance run unattended.
• If food sticks to the wall of the blender jar or bowl, switch off the appliance and unplug
it. Then use a spatula to remove the food from the wall.
• Be careful when you handle or clean the inserts, the blade unit of the food processor,
and the blade unit of the blender and the mini chopper. The blade units and the inserts
are very sharp.
• Do not touch the blades, especially when the appliance is plugged in. The blades are
very sharp.
• If the blades get stuck, unplug the appliance before you remove the ingredients that
block the blades.
Caution
• Never switch off the appliance by turning the blender jar, the bowl, or their lids. Always
switch off the appliance by turning the speed selector to 0.
• Unplug the appliance immediately after use.
• Always unplug the appliance before you reach into the blender jar with your fingers or
an object (for example, a spatula).
• Wait until the moving parts stop running before you remove the lid of the bowl or jar.
• Do not exceed the maximum level indication on the jar or the bowl.
• Thoroughly clean the parts that come into contact with food before you use the
appliance for the first time.
• Before you remove or clean the inserts, kneading hooks, or discs, unplug the appliance.
• Never use any accessories or parts from other manufacturers or that Philips does not
specifically recommend. If you use such accessories or parts, your guarantee becomes invalid.
• This appliance is intended for household use only.
• Do not exceed the quantities and processing time indicated in the user manual.
• Let hot ingredients cool down (< 80ºC) before processing them.
• Always let the appliance cool down to room temperature after each batch that you
process.
• Certain ingredients may cause discolorations on the surface of the parts. This does not
have a negative effect on the parts. The discolorations usually disappear after some time.
Note
• Noise level = 78 dB [A]
Electromagnetic fields (EMF)
This Philips appliance complies with all standards regarding electromagnetic fields (EMF). If
handled properly and according to the instructions in this user manual, the appliance is safe
to use based on scientific evidence available today.
Recycling
Your product is designed and manufactured with high quality materials and components,
which can be recycled and reused.
When you see the crossed-out wheel bin symbol attached to a product, it means the
product is covered by the European Directive 2002/96/EC:
Never dispose of your product with other household waste. Please inform yourself about
the local rules on the separate collection of electrical and electronic products. The correct
disposal of your old product helps prevent potentially negative consequences on the
environment and human health.
1
HR7761
HR7762
HR7763
5 x 1 sec
5 x 1 sec
30 sec
60 sec
45 sec
30 sec
2-3 min
60-180 sec
60-180 sec
(HR7761) 30 sec
30 sec
30 sec
30 sec
30 sec
(HR7762, HR7763)
30 sec
AR
30 sec
FA
30 sec
30 sec
30 sec
(HR7762, HR7763)
30 sec
(HR7763)
30 sec
30 sec
(HR7762)
30 sec
30 sec
30 sec
30 sec
30 sec
30 sec
5 sec
1 min
1 min
1 min
P x 9
3 min
(HR7762, HR7763)
2 Introduction
Congratulations on your purchase and welcome to Philips! To fully benefit from the support
that Philips offers, register your product at www.philips.com/welcome.
This appliance is equipped with a built-in safety lock. You can only switch on the appliance
after you correctly assemble the following parts on the motor unit:
• the food processor bowl and its lid, or
• the blender jar and its lid, or
• the mini chopper.
If these parts are assembled correctly, the built-in safety lock is unlocked.
For recipes, go to www.philips.com/kitchen
3 Food processor
Blade unit
Before you start, make sure that you assemble according to Fig. 2.
You can use the blade unit to chop, mix, blend, or puree ingredients.
Caution
•
Do not use the blade unit to chop hard ingredients, like coffee beans, turmeric, nutmeg, and ice
cubes, as this may cause the blade to get blunt.
Note
•
Do not let the appliance run too long when you chop (hard) cheese or chocolate. Otherwise these
ingredients become too hot, start to melt, and turn lumpy.
•
Precut large pieces of food into pieces of approx. 3 x 3 x 3 cm.
1
Turn the bowl clockwise to fix it on the motor unit, and then put the shaft in the bowl.
» When the bowl is fixed correctly, you hear a click.
2
Take the blade unit out of the protective cover.
3
Put the blade unit on the shaft.
4
Put the ingredients in the bowl.
5
Put the lid on the bowl, and then turn the lid clockwise to fix it.
» When the lid is assembled correctly, you hear a click and the lid is fixed to the
bowl handle.
6
Put the pusher into the feeding tube.
7
Connect the power plug to the power supply.
8
Select the speed that matches the color of the accessory - speed 1.
9
After use, turn the speed selector to 0, and then unplug the appliance.
Tip
• When you chop onions, turn the speed selector to P a few times to prevent the onions from
becoming too finely chopped.
• How to remove food that sticks to the blade or to the inside of the bowl? 1. Switch off the appliance,
and then unplug it. 2. Remove the lid from the bowl. 3. Remove the ingredients from the blade or
from the side of the bowl with a spatula.
Kneading accessory
Before you start, make sure that you assemble according to Fig. 3.
You can use the kneading accessory to knead yeast dough for bread and pizzas. You need to
adjust the amount of liquid to form the dough according to the humidity and temperature
condition.
1
Turn the bowl clockwise to fix it on the motor unit, and then put the shaft in the bowl.
» When the bowl is fixed correctly, you hear a click.
2
Put the kneading accessory on the shaft.
3
Put the ingredients in the bowl.
4
Put the lid on the bowl, and then turn the lid clockwise to fix it.
» When the lid is assembled correctly, you hear a click and the lid is fixed to the
bowl handle.
5
Connect the power plug to the power supply.
6
Select the speed that matches the color of the accessory - speed 1.
• Depending on the recipe, pour liquid ingredient into the feeding tube while the
device is turned on.
7
After use, turn the speed selector to 0, and then unplug the appliance.
2 3
(MAX)
500 g
P
500 g P/2
50 g 2
250 g 1
250 g 2
200 g 2
500 g
1
360 ml
350 ml 1
4 pcs 1
500 g 1
5
200 g 1
2 pcs 1
500 g 1
300 g 1
1
500 g
1
200 g
1
2 pcs
1
500 g
300 g 1
500 g 1
500 g 1
6
2 pcs
200 g 1
500 g 1
40 g 2
70 g 2
40 g 2
50 g 2
100 g P
1 L
2
1 L 2
13
1 L 2
6 x P
400 g
2
600 ml
Discs and Inserts
Before you start, make sure that you pick your desired disc from following and assemble
according to Fig. 4 and Fig. 5:
• Emulsifying disc
• Reversible slicing / shredding disc (fine) (HR7762 and HR7763 only)
• Reversible slicing / shredding disc (coarse) (HR7762 and HR7763 only)
• French fry disc (HR7762 and HR7763 only)
• Granulating disc (HR7762 only)
• Julienne disc (HR7763 only)
Caution
• Be careful when you handle the slicing blade of disc. It has a very sharp cutting edge.
• Never use the disc to process hard ingredients, like ice cubes.
• Do not exert too much pressure on the pusher when you press ingredients into the feed tube.
1
Turn the bowl clockwise to fix it on the motor unit, and then put the shaft in the bowl.
» When the bowl is fixed correctly, you hear a click.
2
Put the disc on the shaft. For inserts (HR7761 only), place an insert in the insert holder
as indicated below, then place the insert holder with insert on the shaft.
Place the opening of the insert over the shaft of the insert holder.
Push the opening of the insert over the projection on the shaft.
Press the insert onto the insert holder until it locks in position with a click.
3
Put the lid on the bowl, and then turn the lid clockwise to fix it.
» When the lid is assembled correctly, you hear a click and the lid is fixed to the
bowl handle.
4
Put the ingredients into the feeding tube with the pusher. Fill the feeding tube evenly for
the best results. When you have to process a large amount of ingredients, process small
batches and empty the bowl between batches.
5
Connect the power plug to the power supply.
6
Check the preparation time, the maximum amount and the speed setting required for
the ingredients in Table 1. Select the speed that matches the color of the accessory.
7
After use, turn the speed selector to 0, and then unplug the appliance.
4 Mini chopper
Before you start, make sure you assemble according to Fig. 6.
Caution
• Do not use the mini chopper to chop hard ingredients, like nutmeg, Chinese rock sugar, or ice cubes.
• Never use the mini chopper for more than 30 seconds without interruption.
• Assemble the sealing ring onto the blade unit before you attach the blade unit to the mini chopper,
to avoid leakage.
• Always process cloves, star anise, and aniseed together. If processed separately, these ingredients may
attack the plastic materials of the appliance.
• The mini chopper beaker may become discolored when you use the mill to process ingredients, like
cloves, anise, and cinnamon.
•
Do not use the mini chopper to process liquids like fruit juice.
•
Let hot ingredients cool down (< 80ºC) before processing them.
1
Put the ingredients in the mini chopper beaker within the maximum indication.
2
Turn the blade unit anticlockwise on the mini chopper beaker until it is fixed properly.
3
Turn the mini chopper clockwise onto the motor unit until you hear a click.
4
Connect the power plug to the power supply.
5
Select the speed that matches the color of the accessory - speed 2. Let it run for about
10-30 seconds until the ingredients are fine enough.
6
After use, turn the speed selector to 0, and then unplug the appliance.
7
Turn the mini chopper anticlockwise to take it off from the motor unit.
8
Turn the blade unit clockwise to take it off from the mini chopper beaker.
Tip
•
For best results when processing beef, please use refrigerated beef cubes.
•
How to remove the ingredients that stick to the side of the mini chopper? 1. Switch off the appliance,
and then unplug it. 2. Remove the beaker from the blade unit. 3. Remove the ingredients from the
blade or from the side of the beaker with a spoon.
5 Blender
Before you start, make sure you assemble according to Fig. 7.
The blender is intended for:
• Blending fluids, like dairy products, sauces, fruit juices, soups, mixed drinks, and shakes,
• Mixing soft ingredients, like pancake batter,
• Pureeing cooked ingredients, like baby food.
4 8
9
7
11
HR7762, HR7763
Note
•
Do not exert too much pressure on the handle of the blender jar.
•
Never open the lid to put your hand or any object in the jar while the blender is running.
•
Always assemble the sealing ring onto the blade unit before you attach the blade unit to the blender jar.
•
To add liquid ingredients during processing, pour them into the blender jar through the feeding hole.
•
Precut solid ingredients into small pieces before you process them.
•
If you want to prepare a large quantity, process small batches of ingredients instead of a large quantity at once.
•
Use cooked ingredients when you blend a soup.
•
To avoid spillage: When you process a liquid that is hot or tends to foam (for example, milk), do not
put more than 1 liter of liquid in the blender jar.
•
If you are not satisfied with the result, switch off the appliance and stir the ingredients with a spatula.
Remove some of the contents to process a smaller quantity or add some liquid.
1
Turn the blade unit on the blender jar.
2
Place the blender jar on the motor unit and turn it clockwise to fix it.
» When the jar is fixed correctly, you hear a click.
3
Put the ingredients in the blender jar within the maximum level indication.
4
Place the lid on the blender jar, and then turn it clockwise to fix it.
5
Connect the power plug to the power supply.
6
Select the speed that matches the color of the accessory - speed 2.
7
After use, turn the speed selector to 0, and unplug the appliance.
Tip
•
How to remove the ingredients that stick to the side of the blender jar? 1. Switch off the appliance,
and then unplug it. 2. Open the lid, and then use a spatula to remove the ingredients from the side of
the jar. 3. Keep the spatula at least 2 cm from the blade.
6 Cleaning and storage
Caution
• Before you clean the appliance, unplug it.
• Make sure that the cutting edges of the blades, discs, and the inserts do not come into contact with
hard objects. This may cause the blade to get blunt.
• The cutting edges are sharp. Be careful when you clean.
1
Clean the motor unit with a moist cloth.
2
Clean the other parts in hot water (< 60ºC) with some washing-up liquid or in a
dishwasher.
3
Store the product in a dry place.
Quick cleaning
You can follow the following steps to clean the food processor bowl and blender jar easier.
Note
•
Make sure that the blade is assembled in the bowl if you clean the food processor bowl.
1
Pour lukewarm water (not more than 0.5 liters) and some washing-up liquid into the
food processor bowl or blender jar.
2
Place the lid on the food processor bowl or blender jar, and then turn it clockwise to
fix it.
3
Turn the speed selector to P until the bowl or jar is clean.
4
Let the appliance run for 30 seconds or until the food processor bowl or blender jar is
clean.
5
Detach the blender jar or food processor bowl and rinse it with clean water.
7 Guarantee and service
If you have a problem, need service, or need information, see www.philips.com/support or
contact the Philips Consumer Care Center in your country. The phone number is in the
worldwide guarantee leaflet. If there is no Consumer Care Center in your country, go to your
local Philips dealer.
10
HR7761
12
1/2
3140 035 29951