Panasonic BL-C30 Getting Started page 3

To Set Up Internet Access to the Camera
Select the camera on the camera list to set up the
Internet access and click [Execute].
• This program searches for the cameras that are connected to the
router and displays the MAC Addresses, IP addresses and Port
Numbers.
• When searching for multiple cameras, the cameras can be identified with the
MAC Addresses labeled near the Ethernet (LAN) port of the cameras.
Note
If more than 20 minutes have passed since the camera was turned on, the
camera cannot be set up from the Setup Program. In this situation, restart the
camera.
Click [Automatic Setup (Internet Access)].
• For the first time installation or after pressing the Factory Default Reset
button, only [Automatic Setup (Local Access Only)] can be selected. To set
up the camera with Static or DHCP settings, after performing the [Automatic
Setup (Local Access Only)], run the Setup Program again and select
[Manual Setup].
The Enter Network Password window is displayed. Enter the
User Name and Password that were set, and click [OK].
When using a router supporting UPnP
When using a router not supporting UPnP
[Disable]. Then click [Next>].
• Check if your router supports UPnP
• If you select [Disable], skip to step
Select a camera.
TM
, check [Enable].
TM
, check
TM
referring to the router's manual.
.
Registration with the "Viewnetcam.com FREE DDNS service"
By registering with the Viewnetcam.com FREE DDNS service, you can
create a personalized web address at which your camera's live video
can always be found on the Internet. For detailed information, access
"http://www.viewnetcam.com".
" ".
To register with the "Viewnetcam.com FREE DDNS service",
check [Register with Viewnetcam.com] and click [Next>].
• When [Do not register with Viewnetcam.com] was selected at step
skip to step .
The Enter Network Password window is displayed.
Enter the User Name and Password that were set,
and click [OK].
After a while, the "Viewnetcam.com FREE DDNS
service" website is displayed. Follow the displayed
instructions for registration.
• If the message "Failed to configure the router's Port Forwarding by UPnP"
is displayed, your router may not support UPnP
enabled. Enable your router's UPnP
following the router's manual and try Automatic Setup again. For more
information about setting up a router, refer to the Panasonic Network
Camera support website at
http://panasonic.co.jp/pcc/products/en/netwkcam/.
• If the message "Failed to register with Viewnetcam.com." is displayed, con-
firm that the router is connected to the Internet.
When "Setup completed" is displayed, click [To
Single Camera page].
When [Enable] was selected
•
.
at step
Notes
• The port number must be specified at the end of camera URL.
For example
Using port 80: http://(Cameraname).viewnetcam.com
or http://IP Address
Using any other port: http://(Cameraname).viewnetcam.com:Port Number
or http://IP Address:Port Number
• The URL for the local network access may be different from the one set up on
the previous page.
When the Single Camera page is displayed, the
setup is completed.
If Security Warning window is displayed to install ActiveX Controls,
•
click [Yes].
To install ActiveX Controls on Microsoft Windows XP Service Pack 2,
•
follow the steps shown below.
1. Click the warning displayed above the tabs, and click [Install
ActiveX Control...].
2.
Click [Install] on Security Warning window.
,
TM TM
or UPnP is not
TM
or set Port Forwarding manually
When [Disable] was selected at
•
step .
•
The image is a simulated screen image.
Notes
•
The banner is displayed only when
Internet access is allowed on the camera.
•
To ensure that the most current image is
displayed, Internet Explorer should be
configured as follows.This will not have
any negative result on normal use.
1. While viewing any website, click
[Tools] [Internet Options].
2. In the section "Temporary Internet
Files", click [Settings] and check
[Every visit to the page].