Genius Euro Bat Manual page 8

Read the end-user guide carefully before using the product
and keep it in a safe place for future reference.
GENERAL SAFETY REGULATIONS
When correctly installed and used, the EURO BAT automation
system ensures a high degree of safety.
A few simple rules should be followed to prevent accidental
problems.
- Do not pass through the gate while the leaves are still moving:
always wait until they have opened completely.
- Do not stand between the leaves.
- Do not stand near the automation system; do not allow
children or adults to stand near it; and do not leave objects
near it.
- Keep control devices or other devices that might accidentally
activate the automation system out of the reach of children.
- Do not allow children to play with the automation system.
- Do not obstruct movement of the leaves.
- Do not allow branches or bushes to obstruct movement of
the leaves.
- Ensure that the warning lamps are in always in working order
and visible.
- Do not attempt to actuate the leaves manually unless you
have first unlocked them.
- In case of a malfunction, unlock the leaves to allow vehicles
to pass through, and call a qualified technician.
- If you have set manual mode, disconnect the power supply
before restoring normal operation.
- Do not modify the components of the automation system.
- Do not attempt to repair the automation system or to perform
any operation on it. Call qualified technicians only.
- At least once every 6 months, have qualified personnel
check that the automation system, safety devices and earth
connection are in working order.
DESCRIPTION
The EURO BAT automation consists of two electromechanical
operators which are ideal for controlling swinging gates with
leaves up to 3 m long each with operators with a 300mm stroke,
and up to 4 m long each with operators with stroke up to 400
mm.
The two electromechanical operators transmit movement to
the leaves by a worm screw system.
The operators are controlled by an electronic control unit
mounted in an enclosure which assures adequate protection
against atmospheric agents.
Together with the installation technician, decide on the type of
operation you want to set for your gate.
The leaves are normally closed. When the electronic control
unit receives an open command from the remote radio control
or any other control device, it activates the electromechanical
system and causes the leaves to turn to the open position so
as to permit access.
For detailed information on the operation of the automation
system in the various operating modes, contact the installation
technician.
The automation system is equipped with a photocell safety
device which prevents the leaves from closing when the
photocells are darkened by an obstacle.
The EURO BAT automation system is also equipped with an anti-
crushing safety device (fitted as standard) that limits the torque
transmitted to the leaves.
The EURO BAT operators ensure that the system is mechanically
locked when the motor is not running, so there is no need to
install a lock.
The leaves can be opened manually only by operating the
unlocking device.
The lamp flashes while the leaves are moving.
ENGLISH
MANUAL OPERATION
In automation systems fitted with the EURO BAT operator, if the
gate has to be operated manually due to a malfunction or
power supply failure, remove the safety cap and insert the key
provided into the release system as shown in fig. 1.
To release the operator, turn the key in the leaf closure direction
(fig. 1).
Open or close the leaf manually.
RETURNING TO NORMAL OPERATION
Turn off the electricity supply to the system before re-locking
the operators to avoid all risk of them starting accidentally
during this operation.
To re-lock the operator, turn the key in the leaf opening
direction (fig. 1).
Lire attentivement les instructions avant d'utiliser le produit et
conserver la notice d'instructions pour toute consultation ultérieure.
RÈGLES DE SÉCURITÉ
L'automatisme EURO BAT, si correctement installé et utilisé,
garantit un haut degré de sécurité.
L'observation des simples règles de comportement suivantes
permettra d'éviter de fâcheux inconvénients:
- Ne pas s'engager portail en mouvement. Il faut toujours
attendre l'ouverture complète du portail avant de s'engager.
- Ne pas stationner entre les vantaux.
- Ne pas stationner et empêcher quiconque de stationner à
proximité de l'automatisme, notamment pendant son
fonctionnement.
- Tenir à l'écart des enfants toutes radiocommandes ou
n'importe quel autre générateur d'impulsions, afin d'éviter
toute manoeuvre accidentelle de l'automatisme.
- Empêcher les enfants de jouer avec l'automatisme.
- Ne pas arrêter volontairement le mouvement du portail.
- Éviter que toutes branches ou tous arbustes puissent entraver
le mouvement du portail
- Toujours conserver efficaces et bien visibles les systèmes de
signalisation lumineuse.
- Ne pas tenter d'actionner manuellement le portail si ce n'est
qu'après son déverrouillage.
- En cas de mauvais fonctionnement, déverrouiller le portail
pour permettre le passage et attendre l'intervention d'un
technicien spécialisé.
- Avant de rétablir le fonctionnement normal du système,
après que le portail ait été déverrouillé pour être actionné
manuellement, il faut couper l'alimentation en énergie
électrique au système.
- Ne pas procéder à des modifications des composants du
système.
FRANÇAIS