Extension Cords - Black & Decker GL800 Instruction Manual

18 • ENGLISH
f Before use check the supply and extension cord
for signs of damage or aging. If the cord becomes
damaged during use, disconnect the cord from
the supply immediately.
Note: Do not touch the cord before disconnecting
the supply. Do not use the line trimmer if the cord
is damaged or worn.
f Keep extension cord away from cutting line.
f Never allow children or people unfamiliar with these
instructions to use the line trimmer.
f Avoid using the line trimmer, while people, especially
children or pets, are nearby.
f Use the line trimmer only in daylight or good artificial
light.
f Never operate the line trimmer with damaged guards
or without guards in place.
f Switch on the line trimmer only when the hands and
feet are away from the cutting head.
f Never fit metal cutting blades.
f Use only the manufacturer's recommended
replacement parts and accessories.
f Always disconnect the line trimmer from the mains
when leaving the line trimmer unattended.
f Disconnect the line trimmer from the mains before
carrying out maintenance or cleaning work.
f Inspect and maintain the line trimmer regularly.
Have the line trimmer repaired only by an authorized
repairer.
f Take care against injury from the blade(s) fitted for
trimming the cutting line length. After extending new
cutting line, always return the line trimmer to its
normal operating position before switching on.
f When not in use, store the line trimmer out of the
reach of children.
f Face the cutting head away from yourself, other
people and animals while the power is connected to
the line trimmer (especially during operation).
f Disconnect the power when changing spools or
clearing grass from under the guard.
f Disconnect the power from the line trimmer before
making any adjustments.
f Use both handles.
f Keep ventilation openings clear of debris. Keep
handles dry, clean and free of oil and grease.
f Never reach underneath the line trimmer (the cutting
line area) until it has completely stopped and the
power has been disconnected.

EXTENSION CORDS

Make sure your extension cord is in good condition. When
using an extension cord, be sure to use one heavy enough
to carry the current your product will draw. An undersized
cord will cause a drop in line voltage resulting in loss
of power and overheating. The following table shows
the correct size to use depending on cord length and
nameplate ampere rating. If in doubt, use the next heavier
gage. The smaller the gage number, the heavier the cord.
Minimum gage for cord sets
Volts Total length of cord in feet
120V 0 - 25
220V 0 - 50 51 - 100
Amperios
More No more
than than
0 - 6 A 18
6 - 10 A 18
10 - 12 A 16
12 - 16 A 14
FEATURES (Fig. A)
1. Main Handle
2. On/Off Switch
3. Cord Retainer
4. Auxiliary Handle
5. Safety Guard
6. Cutter Head
ASSEMBLY
Warning! Before assembly, make sure that the line
trimmer is switched off and unplugged.
Tools required for assembly (not included):
Phillips Screwdriver.
Installation of Two-Part Guard
Warning! The guard must always be installed on the
tool to protect the user.
f Remove the two sections of the guard from the box.
f Place the first section of the guard. In order to do this,
insert the side tab into the slot around the cover, as
shown in Fig. B. Align the guard hole with the pole on
the trimmer cover.
f Remove the screw on the second section of the guard.
f Insert the top tab of the second section of the guard
into the first section of the guard, as shown in Fig. C.
Nota: the rib behind the tab must fastened over the rib of
the first section of the guard Fig. C.
f Insert the side tab of the first section of the guard into
the slot of the second section of the guard until you
hear it click Fig. D.
f To complete the guard assembly, adjust the 19mm
(3/4'') screw, as shown in Fig. E.
f Once installed, remove the cover from the cutting
blade on the end of the second section of the guard.
26 - 50 51 - 100
101 - 200
Wire gauge
16 16
16 14
16 14
12 Not recommended
101 - 150
201 - 300
14
12
12