Download the driver program. The driver software can be downloaded from the Pioneer website. • When downloading the driver program, designate the folder where you wish the program to be saved.
Page 3
Use a proper USB cable to connect a computer to a device equipped with Click on [Next]. USB DAC connector, then turn on the power. For more information regarding connections, check the Operating Instructions for this device. A–type AC IN AL OUT DIGITAL IN Click on [Install].
Page 4
“Programs and functions”, and proceed to step 3. From the Control Panel menu, click on [Add or Remove Programs]. Select [Pioneer N-70A N-50A USB Audio], then click on either [Remove] or [Uninstall]. The uninstaller dialog will appear.
Page 5
Click on [Universal Serial Bus controllers] and confi rm that [USB Composite Device] is listed. If the [Pioneer N-70A N-50A USB Audio] does not appear, confi rm that the USB DAC port has been selected as input source. Then try reconnecting the cable or turning the power off and then on again;...
Page 6
Click on the [Audio] tab, then confi rm that [Pioneer N-70A N-50A USB Audio] 2. To disable the operating system’s sound scheme is listed as the [Default device] for [Sound playback]. If another device has been selected, open the drop-down menu and select [Pioneer Under default OS settings, computer events may be accompanied by audio signals and beeps N-70A N-50A USB Audio], then click on [Apply] to change the selection.
Page 7
From the [Tasks] list, click on [Device Manager]. If the [Pioneer N-70A N-50A USB Audio] does not appear, confi rm that the USB DAC port has been selected as input source. Then try reconnecting the cable or turning the power off and then on again;...
Page 8
USB Audio] is checked as the default device. If another device has been selected, select [Pioneer N-70A N-50A USB Audio], and click to [Set Default]. Speakers Confi rm that your media player’s sound volume is set to Maximum.
Page 9
Click on the [Sounds] tab, and for the [Sound scheme], select [No Sounds], Click on [Start] [Control Panel] [Hardware and Sound] [Sound]. then click on [Apply]. Under the [Playback] tab, for [Speakers], double click on [Pioneer N-70A N-50A USB Audio] to display the Properties. Procedure finished.
Page 10
Under the [Advanced] tab, select for [Default Format] the desired output sampling rate, then click on [Apply]. Procedure finished.
Page 11
Click on [Start] [Control Panel] [Hardware and Sound] [Sound]. Procedure continues. If the [Pioneer N-70A N-50A USB Audio] does not appear, confi rm that the USB DAC port has been selected as input source. Then try reconnecting the cable or turning the power off and then on again;...
Page 12
If the Speaker Mute indicator (at the left side of the Balance button) is lighted, click it to turn it off. If another device has been selected, select [Pioneer N-70A N-50A USB Audio], and click on [Set Default]. Confi rm that your media player’s sound volume is set to Maximum.
Page 13
Click on the [Sounds] tab, and for the [Sound scheme], select [No Sounds], Click on [Start] [Control Panel] [Hardware and Sound] [Sound]. then click on [Apply]. Under the [Playback] tab, for [Speakers], double click on [Pioneer N-70A N-50A USB Audio] to display the Properties. Procedure finished.
Page 14
Under the [Advanced] tab, select for [Default Format] the desired output sampling rate, then click on [Apply]. Procedure finished.
Page 15
“Category”. Procedure continues. If the [Pioneer N-70A N-50A USB Audio] does not appear, confi rm that the USB DAC port has been selected as input source. Then try reconnecting the cable or turning the power off and then on again; when this is done, the [Pioneer N-70A N-50A USB Audio] should be recognized.
Page 16
If the Speaker Mute indicator (at the left side of the Balance button) is lighted, click it to turn it off. If another device has been selected, select [Pioneer N-70A N-50A USB Audio], and click on [Set Default]. Confi rm that your media player’s sound volume is set to Maximum.
Page 17
Click on the [Sounds] tab, and for the [Sound scheme], select [No Sounds], is set to “Category”. then click on [Apply]. Under the [Playback] tab, for [Speakers], double click on [Pioneer N-70A N-50A USB Audio] to display the Properties. Procedure finished.
Page 18
Under the [Advanced] tab, select for [Default Format] the desired output sampling rate, then click on [Apply]. Procedure finished.
Page 19
PIONEER ELECTRONICS AUSTRALIA PTY. LTD. 5 Arco Lane, Heatherton, Victoria, 3202, Australia, TEL: (03) 9586-6300 http://www.pioneer.com.au PIONEER ELECTRONICS DE MEXICO S.A. DE C.V. Blvd.Manuel Avila Camacho 138 10 piso Col.Lomas de Chapultepec, México, D.F. 11000 TEL: 55-9178-4270 http://pioneer-mexico.com Pioneer China Holding Co., Ltd.