1. Manuals
  2. Brands
  3. Century Manuals
  4. Battery Charger
  5. 1010
  6. Owner's manual

Century 1010 Owner's Manual

Hide thumbs
Table of Contents

Advertisement

Available languages

Available languages

Quick Links

B
ATTERY
O
WNER
A
IMPORTANT SAFETY INSTRUCTIONS - READ THESE FIRST
1. SAVE THESE INSTRUCTIONS - This manual
contains important safety and operating instructions
for models 1010, 1014, 1050, 1060, 1150, 1160,
1200, 87102, 87104, 87105, 87106, 87120, 87122,
87128, 87150, 87151, 87302, & YA510B.
2. Do not expose charger to rain or snow.
3. Use of an attachment not recommended or sold by
Century Mfg. Co. may result in a risk of fire, electric
shock, or injury to persons.
4. To reduce risk of damage to electric plug and cord,
pull by plug rather than cord when disconnecting
charger.
5. An extension cord should not be used unless
absolutely necessary. Use of improper extension cord
could result in a risk of fire and electric shock. If
extension cord must be used, make sure:
a. That pins on plug of extension cord are the same
number, size, and shape as those of plug on
charger,
b. That extension cord is properly wired and in good
electrical condition; and
c. That the wire size is large enough for the length of
cord as specified below.
Length of cord in feet:
25
AWG size of cord:
18
B
1. Someone should be within range of your voice or
close enough to come to your aid when you work near
a lead-acid battery.
2. Have plenty of fresh water and soap nearby in case
battery acid contacts skin, clothing, or eyes.
3. Wear complete eye protection and clothing protection.
Avoid touching eyes while working near battery.
4. If battery acid contacts skin or clothing, wash
immediately with soap and water. If acid enters eye,
immediately flood eye with running cold water for at
least 10 minutes and get medical attention
immediately.
5. NEVER smoke or allow a spark or flame in vicinity of
battery or engine.
C
HARGER
'
M
S
ANUAL
50
100
150
18
16
14

PERSONAL PRECAUTIONS

Congratulations on purchasing the finest new charger
on the market today. We wish to acknowledge UL for
their contribution of the following important safety
precautions. Please read and retain these instructions
for the continued safe use of your new charger.
6. Do not operate charger with damaged cord or plug.
Replace the cord or plug immediately.
7. Do not operate charger if it has received a sharp blow,
been dropped, or otherwise damaged in any way; take
it to a qualified serviceman. Call 1-800-328-2921 and
ask for the location of a service center near you.
8. Do not disassemble charger; take it to a qualified
serviceman when service or repair is required.
Incorrect reassembly may result in a risk of electric
shock or fire.
9. To reduce risk of electric shock, unplug charger from
outlet before attempting any maintenance or cleaning.
Turning off controls will not reduce this risk.
10. WARNING - RISK OF EXPLOSIVE GASES.
a. WORKING IN VICINITY OF A LEAD-ACID
BATTERY IS DANGEROUS. BATTERIES
GENERATE EXPLOSIVE GASES DURING
NORMAL BATTERY OPERATION. FOR THIS
REASON, IT IS OF UTMOST IMPORTANCE THAT
EACH TIME BEFORE USING YOUR CHARGER,
YOU READ THIS MANUAL AND FOLLOW THE
INSTRUCTIONS EXACTLY.
b. To reduce risk of battery explosion, follow these
instructions and those published by battery
manufacturer and manufacturer of any equipment
you intend to use in vicinity of battery. Review
cautionary marking on these products and in
engine compartment.
6. Be extra cautious to reduce risk of dropping a metal
tool onto battery. It might spark or short-circuit battery
or other electrical part that may cause explosion.
7. Remove personal metal items such as rings,
bracelets, necklaces, and watches when working with
a lead-acid battery. A lead-acid battery can produce a
short-circuit current high enough to weld a ring or the
like to metal, causing a severe burn.
8. Use charger for charging LEAD-ACID battery only. It
is not intended to supply power to a low voltage
electrical system other than in a starter-motor
application. Do not use battery charger for charging
dry-cell batteries that are commonly used with home
appliances. These batteries may burst and cause
injury to persons and damage to property.
9. NEVER charge a frozen battery.
1
E
n
g
l
i
s
h
F
r
a
n
ç
a
i
s
E
s
p
a
ñ
o
l
Form# 842-240-000

Advertisement

Table of Contents
loading

Related Manuals for Century 1010

Summary of Contents for Century 1010

  • Page 1: Personal Precautions

    3. Use of an attachment not recommended or sold by 8. Do not disassemble charger; take it to a qualified Century Mfg. Co. may result in a risk of fire, electric serviceman when service or repair is required. shock, or injury to persons.

  • Page 2: Grounding And Ac Power Cord Connection Instructions

    PREPARING TO CHARGE BATTERY 1. If necessary to remove battery from vehicle to charge, 4. Add distilled water in each cell until battery acid always remove grounded terminal from battery first. reaches level specified by battery manufacturer. This Make sure all accessories in the vehicle are off, so as helps purge excessive gas from cells.

  • Page 3: Engine Starting

    NEGATIVE (Black) charger clip to the free end of the cable. ENGINE STARTING NOTE: Not applicable to Model 1010,1014, 87102, and 4. If engine fails to start, charge battery for another 5- 87122. 15 minutes and attempt to start the engine again.
  • Page 4 Note: Charger will continue to “hum” as it monitors reaching full charge. battery charge level. MODEL 87102 & 1010 Step 1: SELECT FUNCTION (Switch 1) Note: Preactivation of a Select “10 A, 12 V” if you are charging large lead acid...

  • Page 5: Charging A Battery

    Engage starter for 3-4 seconds; if engine fails to start, Select 12 A, 6 V MANUAL position for charging 6 V charge the battery for another 5-15 minutes and attempt batteries used in automobiles, trucks, and farm to start the engine again. equipment.
  • Page 6 then shuts the charger off automatically (12-V settings MODEL 87151 &1160 only). Note: Charger will continue to “hum” as it monitors Charging a Battery-Starting an Engine battery charge level. This charger is equipped with Auto On-off Technology Step 1: SELECT FUNCTION (Switch 1). which senses when a battery has reached full charge and then shuts the charger off automatically (12-V Select “Auto”...
  • Page 7 Step 2: Set VOLT SELECTOR (Bottom MODEL 87302 & 1200 Switch) Step 1: Set RATE SELECTOR (Top Select “6 Volt” for VOLT SELECT Switch) charging and starting 6 RATE SELECT volt batteries used in Select “Low” for 2 Amp, 12 Volt automobiles, trucks and Charging and 6 Amp, 6 Volt Charging.

  • Page 8: Troubleshooting

    It may be damaged, sulfated, or have an open circuit. ALL MODELS (EXCEPT MODELS 1010, 1014, 87102, 87104, & 87122) VEHICLE WILL NOT START WHEN USING THE ENGINE circuit breaker will reset automatically and the START SETTING ammeter needle will again register amperage.

  • Page 9: Limited Warranty

    LIMITED WARRANTY Century Manufacturing Co. warrants that for 2 years from This warranty extends to each person who acquires lawful the date of original retail purchase, it will repair at no...

  • Page 11: Précautions Personnelles

    Century modèles Portez-le chez un technicien qualifié. Appelez le 1-800-328- 1010, 1014, 1050, 1060, 1150, 1160, 1200, 87102,87104, 2921 pour obtenir l’adresse du centre de réparation le plus 87105, 87106, 87120, 87122, 87128, 87150, 87151, 87302 proche.

  • Page 12: Positionnement Du Chargeur

    PRÉPARATION À LA CHARGE DE LA BATTERIE 1. S’il est nécessaire de déposer la batterie du véhicule pour la batterie. Cela permet de purger l’excès de gaz contenu dans charger, toujours débrancher la cosse de masse de la les éléments. Ne pas trop les remplir. Si la batterie ne batterie en premier.

  • Page 13: Mise En Marche Du Moteur

    4. Se placer et positionner l’extrémité libre du câble (installé à Figure 3 MISE EN MARCHE DU MOTEUR NOTA: Ne s’applique pas au modèle 1010, 1014, 87102, et 4. Si le moteur ne se met pas en marche, charger la batterie 87122.

  • Page 14: Instructions D'utilisation

    Charge d’une batterie - Mise en marche d’un l’obtention de la charge maximum de la batterie. moteur MODÈLES 87102 & 1010 Ce chargeur est doté d’un système de marche/arrêt automatique qui détecte si une batterie a atteint la charge maximum puis arrête automatiquement le chargeur (réglages 12 V uniquement).
  • Page 15 NOTA: pour obtenir les meilleurs résultats, commencer par Sélectionner l’une ou l’autre des positions 12 A, 12 V pour charger la batterie en suivant les instructions ci-dessus, pendant charger de grosses batteries à acide de plomb telles celles 5 à 15 minutes. Engager le démarreur pendant 3 secondes. Si le utilisées dans les automobiles, bateaux, camions, fourgonnettes, moteur refuse de démarrer, charger la batterie pendant 5 à...
  • Page 16 Sélectionner “ 15 A, 6 V ” pour charger des batteries de 6 V MODÈLE 87122 utilisées sur les automobiles, camions et machines agricoles. Avec ce réglage, le courant ne s’affaiblit pas. Charge d’une batterie - Après avoir lu le manuel du propriétaire et terminé les Ce chargeur est doté...
  • Page 17 Sélectionner “ 2 A, 12 V ” pour charger des batteries de tracteurs et le démarrage du moteur (6 et 12 volts) de jardin, de motos, de motoneiges ou d’autres petites batteries. NOTA: pour démarrer une automobile dont la batterie est Ne pas utiliser ce réglage pour les grosses batteries affaiblie, charger cette dernière pendant 5 à...

  • Page 18: Dépannage

    • Vérifier que la batterie est en mesure d’être chargée. Elle A ou 15 A - 12 volts (selon le cas). TOUS LES MODÈLES (EXCEPTÉ 1010, 1014, 87102, 87104, 87122) LE VÉHICULE NE SE MET PAS EN MARCHE MALGRÉ LE disjoncteur se réarme automatiquement et l’aiguille de...

  • Page 19: Entretien Du Chargeur

    à la charge des défauts de matériau et/ou de fabrication. Si, à la suite du propriétaire. d’efforts raisonnables de Century, le produit est jugé irréparable, Certaines provinces n’autorisant pas la restriction des garanties Century, au choix, remboursera le prix d’achat initial ou ou la restriction des dommages accessoires ou conséquents, le...

  • Page 21: Precauciones Personales

    ñado de alguna manera. Llévelo a operación para los modelos 1010, 1014, 1050, 1060, 1150, un técnico capacitado para que lo repare. Si necesita la 1160, 1200, 87102, 87104, 87105, 87106, 87120, dirección del centro de servicio más cercano, llame al 1-...

  • Page 22: Ubicacion Del Cargador

    PRÉPARACION PARA CARGAR LA BATERIA 1. Cuando sea necesario sacar la batería del vehículo para de la batería. Esto ayuda a desalojar el exceso de gas de poder cargarla, desconecte primero el terminal de toma a las celdas. No ponga demasiado agua en las celdas. Para tierra.
  • Page 23 Figura 3 BATERIA, para reducir el riesgo de lesiones, conecte la ARANQUE DEL MOTOR NOTA : No corresponde para el modelo 1010, 1014, 87102, y 4. Si el motor no arranca, cargue la batería otros 5 a 15 87122. minutos e intente hacer arrancar el motor otra vez.

  • Page 24: Instrucciones De Funcionamiento

    Carga de la bateria - Arranque del motor alcanzado la carga completa de la batería. Este cargador está equipado con tecnología de encendido MODELOS 87102 Y 1010 automático (Auto-On-Off), ya que cuenta con un sensor que determina cuando se ha cargado totalmente la batería para apagar automáticamente el cargador (12 V solamente).
  • Page 25 Haga arrancar el motor unos 3 segundos; si el motorr no arranca, 2 A, 12 V. No utilice este ajuste para baterías grandes de cargue la bateria de 5 a 15 minutos y trate de hacer arrancar el automóviles, camiones o vehículos marinos. motor nuevamente.
  • Page 26 NOTA: El cargador continuará “zumbando” mientras controla el MODELES 87151, 1160 nivel de carga de la batería. Paso 1: SELECCIONE LA FUNCION Carga de la bateria - Arranque del motor (Interruptor 1) Este cargador está equipado con tecnología de encendido Seleccione “Auto”...
  • Page 27 Seleccione START (encendido) cargue la bateria de 5 a 15 Nota: Si va hacer arrancar un automóvil conuna bateria minutos, luego seleccione la capacidad de carga de la bateria descargada, para obtener mejor resultado, cargue la bateria de para que se continúe cargando. Repetir si la bateria no 5 a 15 minutos y luego, haga comienza a cargar.

  • Page 28: Solucion De Problemas

    Puede estar dañada o sulfatada, o puede tener un circuito abierto. TODOS LOS MODELOS (EXCEPTO LOS MODELOS 1010, 1014, 87102, 87104 , y 87122) EL VEHICULO NO ARRANCA CON LA FUNCION DE minutos. El disyuntor se restablece automáticamente y la ARRANQUE EN EL CARGADOR.

  • Page 29: Garantia Limitada

    Servicio de Cargadores de Baterías, al teléfono (800) 328-2921. GARANTIA LIMITADA Century Manufacturing Co. garantiza que por 2 años desde la Esta garantía se aplica al producto solamente y no a los fecha original de compra, hará la reparación sin cargo de las accesorios incluídos con el producto y sujetos a desgaste;...
  • Page 32 Form No. 842-240-000...

This manual is also suitable for:

101410601050115011601200 ... Show all

Table of Contents