Table of Contents
Advertisement
Quick Links
EN
USER INSTRUCTIONS AND SAFETY
Congratulations on your purchase of an N-Com product.
N-Com B3 was made using the most advanced technologies and the best
materials. Long-running tests and thorough system development have allowed
the highest audio quality to be achieved.
For additional information about B3 visit the website www.n-com.it
Firmware version: 4.0x
REFERENCE STANDARDS
The products of the N-Com line are in compliance with standards as per the table
below:
The
requirements and other applicable provisions of Directive
B3
99/5/CE, Directive 2009/65/EC, Directive 2011/65/CE, Directive
2012/19/EU
Battery
Directive 2006/95, 2004/108, 2009/65/EC, 2011/65/CE,
charger
2012/19/EU, 2009/125/CE
Battery
Directive 2006/66/CE
The Declarations of Compliance can be downloaded from the website www.n-
com.it (Download section).
Y6MNCOM3
FccID:
Bluetooth is a registered trademark property of Bluetooth SIG, Inc.
Bluetooth
system
complies
with
B3
the
main
safety
R-NZ
B3 - 18/01/2016 14:21:00
Advertisement
Table of Contents
Related Manuals for N-Com B3
Summary of Contents for N-Com B3
- Page 1 For additional information about B3 visit the website www.n-com.it Firmware version: 4.0x REFERENCE STANDARDS The products of the N-Com line are in compliance with standards as per the table below: Bluetooth system complies...
-
Page 3: Table Of Contents
MOBILE PHONE FUNCTIONS..................16 GPS SATELLITE NAVIGATOR FUNCTIONS..............17 STEREO FM RADIO......................17 10. MUSIC VIA BLUETOOTH ....................18 11. MUSIC PLAYER VIA CABLE .....................18 12. N-COM RIDER-PASSENGER INTERCOM MODE ............19 12.1.Intercom affiliation.............................19 12.2.Intercom function ...............................19 13. N-COM BIKE-TO-BIKE INTERCOM................19 13.1.Bike-to-Bike pair up ............................19 13.2.Making a Bike-to-Bike call..........................20... -
Page 4: Warnings And Safety
WARNINGS AND SAFETY Read this User Manual carefully, as well as the User Manuals for other N-Com kits that you will be using with the N-Com B3. Read the simple rules listed below. Failure to comply with these rules may lead to dangerous situations. -
Page 5: Appropriate Use
Use the device only in the normal position, as described in the product documentation. Do not attempt to disassemble, tamper with or modify any part of the N-Com system. Caution: Adjust the volume of the N-Com system (where provided) and of the audio sources connected to it before you use the system on the road. -
Page 6: Disposal
1.7. Disposal Refer to this user manual and to manuals related to other parts of the N-Com system in order to disassemble the system from the helmet. Once the system has been disassembled, dispose of it according to the following instructions: ... -
Page 7: Installation
(Fig. 4). Temporarily put the padding on the outside of the helmet (Fig. 5). Remove the N-Com cover from the helmet border gasket. Push from the inside of the helmet to facilitate the removal (Fig. 6). - Page 8 ONLY FOR FULL-FACE HELMETS Remove the chin guard by pulling on the special red tab. Fig. 7 Remove the right and left polystyrene cheek pads by gently pulling them out of the helmet. The helmet shell can be opened slightly to facilitate the removal of the cheek pad.
-
Page 9: Installing The Microphone
3.1. Installing the microphone JET HELMETS OR FLIP-UP HELMETS Fig. 9 Fig. 10 Prepare the microphone by inserting the microphone clamp, being careful to position it properly (Fig. 9) Note: the flat part of the clamp must be facing upward when the microphone is positioned as shown in figure 11. -
Page 10: Installing The System On The Helmet
3.2. Installing the system on the helmet Position the system inside the helmet as shown in figure 15, next to the N-Com housing in the shell. Fig. 15 Looking at the helmet from the outside, slide the rear positioning tab into groove A as shown in the figure;... - Page 11 Insert the microphone connector in the micro USB electronic plate. Before you place the speaker in its housing, apply the Velcro pad to the polystyrene cheek pad (Fig. 19). Fig. 19 Fig. 18 Position the loudspeaker in the special housing obtained in the polystyrene cheek pad (Fig.
- Page 12 ONLY FOR JET HELMETS OR FLIP-UP HELMETS Secure the battery-holder support to the right side of the helmet, lining up the holes with the pins on the shell (Fig. 22) Fig. 22 ONLY FOR FULL FACE HELMETS Position the battery in the right polystyrene cheek pad housing (Fig.
-
Page 13: Removing The System
Fig. 25 Fig. 26 Position the comfort padding in its housing (see specific instructions provided in the helmet user manual), hooking the neck roll (Fig. 25). Position both the comfort cheek pads in their housing (see specific instructions provided in the helmet user manual) making sure that all the press-studs click. -
Page 14: Basic Functions
The switch from one function to the next is confirmed by a vocal message that indicates the system status. When B3 is turned on, the menu is always in the “BASE” mode. Depending on the menu position, you can manage the various audio devices and the available functions:... -
Page 15: N-Com Wizard
The programme can be downloaded from the Internet site www.n-com.it, in the “Download” section. In order to use it, a helmet equipped with B3 must be connected to the PC, using the USB cable supplied with the system. N-Com Wizard allows you to customize your B3, specifically: ... -
Page 16: Affiliation Reset Function
B3 allows a conference call with Rider and Pillion Passenger. When a call comes in on a mobile phone connected via Bluetooth to B3, the Rider-Pillion Passenger intercom is temporarily turned off. However, if you wish to share the phone call with the other helmet, simply turn on the intercom manually during the phone call (by briefly pressing “on”). -
Page 17: Gps Satellite Navigator Functions
However, if you wish to activate the Conference GPS function, simply turn on the intercom manually during the GPS directions (by briefly pressing “on”). Caution: this function is available only if the Pillion Passenger helmet is also equipped with a N-Com system provided with the same function. -
Page 18: Music Via Bluetooth
10. MUSIC VIA BLUETOOTH You can listen to high quality music by connecting the N-Com system to a device equipped with Bluetooth A2DP (Advanced Audio Distribution Profile) protocol. The N-Com system is also equipped with Bluetooth AVRCP (Audio Video Remote Control Profile) protocol, which allows you to stop and resume music reproduction directly from the helmet (with devices equipped with AVRCP). -
Page 19: N-Com Rider-Passenger Intercom Mode
N.B.: The range of the communication varies depending on the N-Com systems used. The B3 system stores up to 4 different B3 systems, so that “calls” can be made to these devices. So that two B3 systems can communicate with one another in the Bike-to-Bike mode, they must be paired up first. -
Page 20: Making A Bike-To-Bike Call
You can display the memory settings of your device (and check the names of the paired up devices) using the “N-Com Wizard” programme for PC or through the “App N-Com” for Smartphone Android. To make it easier to recognize the N-Com systems paired up in “Bike-to-Bike”... -
Page 21: Universal Intercom
14.1. Pairing up the UNIVERSAL INTERCOM To pair up an N-Com system and an intercom of another brand (from now on called Intercom B), the following procedure needs to be carried out: Put the N-Com system in the “Pair up Mode” by pressing the “on” key for more than 4 ... -
Page 22: Battery
15. BATTERY Before using the N-Com device for the first time, recharge the battery completely for at least 10 hours. To obtain best performances from the battery, it is recommended to completely recharge the battery the first few times. Afterwards, you can recharge the battery for shorter periods. Whenever possible, it is best to recharge the battery completely. -
Page 23: Summary Table Of Controls
(2s) Deactivate audio via cable (2s) Connect A2DP device (2s) Disconnect A2PD device (2s) Play music (Play) X (2s) Pause Function (Pause) (2s) Next track (Forward) (4s) Activate N-Com intercom or Universal Intercom Deactivate N-Com intercom or Universal Intercom... - Page 24 Bike 1 pair up (2s) Bike 2 pair up (2s) Bike 3 pair up (4s) Bike 4 pair up (4s) Bike-to-Bike menu enabling/disabling Erase pair ups** (4s) *Briefly press at the same time. **With N-Com system in Pairing up Mode.
-
Page 25: Limited Warranty
Negligence and normal wear of internal and external parts. Any damage caused by an accident; Any change or modification made to the helmet or to the N-Com system by the user or by third parties. Color changes or damages caused by exposure to harmful chemical products. -
Page 26: Validity Of This Limited Warranty
Nolangroup shall not be responsible in case the product presents limited capabilities due to the operating mode of cell phones or of other accessories or equipment not supplied by Nolangroup. Tampering with the internal electronic card or with other parts of the N-Com system shall invalidate the warranty. -
Page 27: Product Identification
Legislative Decree 2 February 2002 n. 24. 17.5. Product identification N-Com products are identified by means of a code that allows product traceability and identification. The identification code is printed on the adhesive label applied to the B3 system. -
Page 28: Warranty Registration Form
18. WARRANTY REGISTRATION FORM Product name: Identification code Buyer’s Information Name Last name Address Phone e-mail Dealer’s stamp Date of purchase...