Care Of The Exterior; Care Of The Spa Cover - HotSpring Grandee NXT Owner's Manual

To remove and replace the spa pillows:
1. Carefully pull and lift on one end of pillow to stretch pillow (longer)
until the pillow is released from the plastic retainer. Once one end
is released, push pillow in opposite direction to remove from other
retainer.
2. Align pillow by locating the arrow on back side of pillow and facing the
arrow upwards.
3. Slide one end of pillow onto the spa retainer.
4. Pull other end of pillow; using both hands lift pillow above retainer and
with a stretching motion slide pillow recess onto retainer.

CARE OF THE EXTERIOR

SPA SHELL
Your HOT SPRING spa has an acrylic shell. Stains and dirt generally
will not adhere to your spa's surface. A soft rag should easily remove
most dirt. Most household chemicals are harmful to your spa's shell
(see below for detailed information on cleaning agents). Always rinse
off any spa shell cleaning agent with fresh water.
IMPORTANT:
1. The following products are the ONLY approved cleaning agents
for your HOT SPRING spa shell: plain water, HOT SPRING
FRESHWATER Spa Shine, Brillianize
alcohol or any other household cleaner other than those listed to
clean the spa shell surface is NOT recommended. DO NOT use any
cleaning products containing abrasives or solvents since they may
damage the shell surface, specifically: Simple Green
Spa Mitt. NEVER USE HARSH CHEMICALS! Damage to the shell
by use of harsh chemicals is not covered under the warranty. Always
rinse off any spa shell cleaning agent with fresh water.
2. Iron and copper in the water can stain the spa shell if allowed to go
unchecked. Ask your HOT SPRING dealer about a Stain and Scale
Inhibitor to use if your spa has a high concentration of dissolved
minerals. (Watkins recommends FRESHWATER Stain & Scale
Defense.)
3. Keep all cleaners out of the reach of children and use care when
applying.
EVERWOOD SPA CABINET
®
HOT SPRING spas include an EVERWOOD HD spa cabinet.
EVERWOOD HD is made from a rigid polymer for durability and adds a
film finish that provides a rich, wood like appearance. .
Cleaning of the EVERWOOD HD consists of simply spraying the cabinet
with a mild soap and water solution to remove any stains and residue.
Do not rub the EVERWOOD HD with an abrasive material or use
abrasive cleaners as this may damage its surface.
Spa Care and Maintenance
® ®
or Soft Scrub . The use of
® ®
, Windex or
Page 23

CARE OF THE SPA COVER

WARNING: The cover is a manual safety cover that meets or
exceeds all prevailing requirements of ASTM 1346-91 for spa safety
covers when installed and used correctly as of the date of manufacture.
Non-secured, or improperly secured covers are a hazard.
Open the cover to its fully open position before use.
VINYL COVER
The vinyl spa cover is an attractive, durable foam insulation product.
Monthly cleaning and conditioning are recommended to maintain its
beauty.
To clean and condition the vinyl cover:
1. Remove the cover from the spa.
2. With a garden hose, spray the cover to loosen and rinse away dirt or
debris.
3. Using a large sponge and/or a soft bristle brush, and using a very mild
soap solution (one teaspoon dishwashing liquid with two gallons of water),
or baking soda (sodium bicarbonate), scrub the vinyl top in a circular
motion. Do not let the vinyl dry with a soap film on it before it can be rinsed
clean.
4. Scrub the cover's perimeter and side flaps. Rinse clean with water.
5. Rinse off the underside of the cover with water only (use no soap), and
wipe it clean with a dry rag.
6. To condition the cover after cleaning, apply a thin film of HOT SPRING
Cover Shield to the vinyl surface and buff to a high luster.
IMPORTANT: To remove tree sap, use cigarette lighter fluid (not charcoal
lighter fluid). Use sparingly, and rinse with a saddle soap solution
immediately afterwards, then wipe dry.
DO:
• Remove snow buildup to avoid breakage of the foam core from the
additional weight of the snow.
• Lock cover lock straps to secure the cover when the spa is not in use.
DON'T:
• Drag or lift the spa cover using either the flaps, or the cover lock straps.
• Walk, stand, or sit on the cover.
• Place any metal or heat transferring object on the cover or place any
type of plastic tarp or drop cloth over the cover as this may result in a
melted foam core, which would not be covered under the warranty.
• Use any lifting mechanisms, chemicals, or cleaners except those
recommended by Watkins Manufacturing Corporation, or its Authorized
Sales and Service Dealer.
Spa Care and Maintenance