Service Function Table - Panasonic KX-FM131RS Simplified Service Manual

2.4.

SERVICE FUNCTION TABLE

Change from original pages 103~105 (2.4.4. SERVICE FUNCTION TABLE)
Code Function
501 Pause time set
502 Recall time set
503 Dial speed select
510 VOX TIME
511 Vox sense
520 CED frequency select
521 International mode select
522 Auto standby select
523 Receive equalizer select
524 Transmission equalizer select
533 Setting the number of times that
massage transfer is redialed.
534 Setting the message transfer/pager
call redial interval
550 Memory clear: To reset the value to the default one, except the top margin (853)
and left margin (854).
552 DTMF single tone test
553 Monitor on FAX communication
select
554 Modem test
555 Scan check
556 Motor test
557 LED test
558 LCD test
559 Document jam detection select
561 KEY test
570 BREAK % select
571 ITS auto redial time set
572 ITS auto redial line disconnection
time set
573 Remote turn-on ring number set
580 TAM continuous tone detection
590 FAX auto redial time set
591 FAX auto redial time disconnection
time set
592 CNG transmit select
Set Value Effective Range
X 100 msec 001~600
X 10 msec 01~99
1:10 pps 2:20 pps 1, 2
1:6 sec 2:4 sec 1, 2
1:HIGH 2:LOW 1, 2
1:2100 Hz 2:1100 Hz 1, 2
1:ON 2:OFF 1, 2
1:ON 2:OFF 1, 2
1:0 km 2:1.8 km 3:3.6 1~4
km 4:7.2 km
1:0 km 2:1.8 km 3:3.6 1~4
km 4:7.2 km
00~99 00~99
001~999 sec 001~999
1:ON 2:OFF 1, 2
1: OFF 2:PHASE B 1~3
3:ALL
1:ON 2:OFF 1, 2
1:61% 2:67% 1, 2
X number of times 00~99
X second 001~999
X number of rings 01~99
1:ON 2:OFF 1, 2
X number of times 00~99
X second 001~999
1: OFF 2:ALL 1~3
3:AUTO
9
Default Remarks
50
70
1
1
1 When the TAM dose not stop
recording the ICM because noise is
detected on the telephone line,
change this setting to "LOW".
1 See the Symptom/
Countermeasure Table for long
distance and international calls in
2.3.3.3.1. Defective facsimile
section.
1 See the Symptom/
Countermeasure Table for long
distance and international calls in
2.3.3.3.1. Defective facsimile
section.
1 The resolution reverts to the
default when transmission is
complete.
1 When the telephone station is far
from the unit or reception cannot
be performed correctly, adjust
accordingly.
1 When the telephone station is far
from the unit or transmission
cannot be performed correctly,
adjust accordingly.
3 Selects the number of times that
message transfer is redialed (not
including the first dialing).
30 Sets the interval of message
transfer/pager call redial.
"START" input"
2 See 2.5. TEST FUNCTIONS.
1
See 2.5. TEST FUNCTIONS.
See 2.5. TEST FUNCTIONS.
0 See 2.5. TEST FUNCTIONS.
See 2.5. TEST FUNCTIONS.
See 2.5. TEST FUNCTIONS.
1 See 2.2.1. Paper Jam.
See 2.5. TEST FUNCTIONS.
1 Sets the % break of pulse dialing
according PBX.
14 Selects the number of times that
ITS is redialed (not including the
first dial).
30 Sets the interval of ITS redialing.
15 Sets the number of rings before
the unit starts to receive a
document in the TEL mode.
1 ON : Stops TAM operation when
Dial tone, etc. are detected.
5 Selects the number of redial times
during FAX communication (not
including the first dial).
45 Sets the FAX redial interval during
FAX communication.
2 Lets you select the CNG output
during FAX transmission. ALL:
CNG is output at phase A. AUTO:
CNG is output only when automatic
dialing is performed. OFF: CNG is
not output at phase A.
KX-FM131RS