Cabclone™ D.i - Mesa/Boogie JP-2C Owner's Manual

The Yellow FX (Loop) Status Indicator LED will track the status of your Effects Loop settings. When using the JP-2C Footswitch and/
or controlling the Channels with the Front Panel Channel Select mini toggle, the status of the FX (Loop) will be determined GLOBALLY
by the setting of the FX mini toggle in the EQ Window. When using Midi to control the JP-2C, the FX (Loop) status will be determined
by either the Factory-burned settings in the JP-2C's processor or whatever was last stored at a given Midi Program Number location
(as is possible as a result of a prior demo at a MESA Dealership).
NOTE: Always use quality (low capacitance) cables of the shortest possible length in the Effects Loop when connecting your processors.
Doing so will help avoid any sonic degradation due to capacitance and help maintain optimum performance when the Loop is in use.
To Store the Effects Loop status in a Channel under a Midi Program location, as with all the other features, you must first "reset" its
location in the JP-2C's switching buss.
Follow these steps to store the FX (Loop) Status in a Channel under a Midi Program location;
1. Go to the desired Midi Program number on your Midi controller of choice.
2. Call up the desired JP-2C Channel with the Front Panel Channel Select mini toggle located in the upper right corner of the EQ
Window.
3. Set the FX mini toggle located in the upper left corner of the EQ window to "MD" (switch down).
4. Move the FX mini toggle to "FX" (switch up).
5. Toggle the STORE switch on the far left (when viewing from front) of the Rear Panel of the JP-2C one time. The current Chan-
nel and FX (Loop) status has been written to the currently displayed Midi Program Number location in the JP-2C's processor.
The Channel and FX (Loop) status is now saved under the current Midi Program Number displayed on your Midi controller and should
be called up again when next you return to that Program Number. If it is not, repeat steps 1 – 5 and check again.
CABCLONE™ D.I.
feature ever to grace a MESA Rear Panel, the on-board CABCLONE D.I. and Cabinet Simulation feature. This built-in direct recording
solution allows you to capture a wonderful representation of the JP-2C's inspiring sound and feed it direct to a Console, Converter or
even direct to a Recorder without the need to mic up a speaker. Impossible you say... a long list of well known producers, engineers
and players would beg to differ with you.
JP-2C™
ALL TUBE MUSIC
AMPLIFIER
SPKR CLOSED
ON BACK
O
P
E
N
CabClone GROUND
SPKR VINTAGE
™
OFF
D.I.
The CabClone™ Section features include:
• SPKR ON/SPKR OFF – SPEAKER Status
• CLOSED BACK/OPEN BACK/VINTAGE – CABINET Style
• CabClone™ D.I. – XLR BALANCED D.I. Output
• LIFT/GROUND – XLR Pin 1 Float .
• +4/-10 – OUTPUT LEVEL Switch
As mentioned in the OVERVIEW in the Front of this Manual, the JP-2C features one of—if not the—coolest
MADE IN PETALUMA, CA
WITH THE WORLD'S
FINEST MATERIALS
Taken directly from our acclaimed stand-alone CABCLONE™ D.I. unit, this speaker-compensated
D.I. XLR Balanced Output (and HEADPHONE Output) does an incredible job of capturing the
LIFT +4 dB
signal from the SPEAKER OUTPUT and turning it into direct-injection gold. The five elements
here in this section of the Rear Panel allow for use with a live speaker or without, so you can
-10 dB
blend the direct signal and a mic'd speaker cabinet if you so desire.
MESA MIDI
FT.SW. THRU/OUT
PATENTED
6,621,907
MIDI
STORE MIDI
IN
CHANNEL
TUBE GUIDE
5 x 12AX7
4 x 6L6
PAGE 21
100 WATTS
60 WATTS