Noise/Vibration Information; Technical Data - Bosch GBH 18 V-LI Original Instructions Manual

OBJ_BUCH-1103-003.book Page 11 Tuesday, March 22, 2011 12:44 PM

Technical Data

The technical data of the machine are listed in the Table on
page 143.
Please observe the article number on the type plate of your
machine. The trade names of the individual machines may
vary.
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with the fol-
lowing standards or standardization documents: EN 60745
according to the provisions of the directives 2004/108/EC,
2006/42/EC.
Technical file at:
Robert Bosch GmbH, PT/ESC,
D-70745 Leinfelden-Echterdingen
Dr. Egbert Schneider Dr. Eckerhard Strötgen
Senior Vice President Head of Product
Engineering Certification
Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
Leinfelden, 17.12.2009

Noise/Vibration Information

The measured values of the machine are listed in the table on
page 143.
Noise and vibrational values (vector sum of three directions)
determined according to EN 60745.
The vibration emission level given in this information sheet
has been measured in accordance with a standardised test
given in EN 60745 and may be used to compare one tool with
another. It may be used for a preliminary assessment of expo-
sure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or poorly maintained,
the vibration emission may differ. This may significantly in-
crease the exposure level over the total working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working pe-
riod.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.
Bosch Power Tools
Mounting and Operation
Action
Changing the position of the auxiliary
handle
Removing the Battery
Inserting the Battery
Checking the battery charge condition 4
Inserting SDS-plus Drilling Tools
Removing SDS-plus Drilling Tools
Selecting the operating mode drilling
or hammer drilling
Reversing the Rotational Direction
Adjusting the drilling depth X
Mounting the extraction system
(Saugfix)
Switching on and off and setting the
speed
Selecting accessories
Maintenance and Cleaning
For safe and proper working, always keep the machine
and ventilation slots clean.
Clean the application tool, the tool holder, the power tool's
ventilations slots, and the battery's ventilation slots each time
after using.
After-sales Service and Customer
Assistance
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. Exploded views and information on spare parts can al-
so be found under:
www.bosch-pt.com
Our customer service representatives can answer your ques-
tions concerning possible applications and adjustment of
products and accessories.
In all correspondence and spare parts order, please always in-
clude the 10-digit article number given on the type plate of
the machine.
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham
Uxbridge
UB 9 5HJ
Tel. Service: +44 (0844) 736 0109
Fax: +44 (0844) 736 0146
E-Mail: boschservicecentre@bosch.com
English | 11
Figure Page
1 144
2 144
3 144
145
5 145
6 145
7 146
8 146
9 147
10 147
11 148
– 149
1 619 929 E64 | (22.3.11)