Page 1
RC–BAS05 VS XS–V30 CX–GV30 • This Service Manual is the “Revision Publishing” and replace “Simple Manual” XS-V30<HR>, (S/M Code No. 09-01A-449-9T1). • If requiring information about the CD mechanism, see Service Manual of BZG-5, (S/M Code No. 09-00C-353-3N8). u163 S/M Code No. 09-01B-449-9R1...
http://www.xiaoyu163.com SPECIFICATIONS 3 7 63 1515 0 GENERAL MAIN UNIT CX-GV30 Power requirements 120 V / 220 230 V / 240 V AC TUNER (Switchable), 50 Hz / 60 Hz FM tuning range 87.5 MHz to 108 MHz Power consumption 157 W FM usable sensitivity (IHF) 13.2 dBf...
http://www.xiaoyu163.com PROTECTION OF EYES FROM LASER BEAM DURING SERVICING 3 7 63 1515 0 CAUTION This set employs laser. Therefore, be sure to follow carefully the instructions below when servicing. Use of controls or adjustments or performance of proce- dures other than those specified herin may result in WARNING!! hazardous radiation exposure.
http://www.xiaoyu163.com NOTE ON BEFORE STARTING REPAIR 1. Forced discharge of electrolytic capacitor of power supply block 3 7 63 1515 0 When repair is going to be attempted in the set that uses relay circuit in the power supply block, electric potential is kept charged across the electrolytic capacitors (C101, 102) even though AC power cord is removed.
Page 5
http://www.xiaoyu163.com 3 7 63 1515 0 In such a case, check also if the POWER AMPLIFIER circuit or power supply circuit has any abnormalities or not. 2-2. Regarding reset There are cases that the machine does not work correctly because the MICROCOMPUTER is not reset even though the AC power cord is re-inserted, or the software reset (pressing the STOP key + POWER key) is performed.
http://www.xiaoyu163.com ELECTRICAL MAIN PARTS LIST 3 7 63 1515 0 REF. NO. PART NO. KANRI DESCRIPTION REF. NO. PART NO. KANRI DESCRIPTION 87-A12-780-090 CAP,E 4700-35 M 85 SKR 87-A12-780-090 CAP,E 4700-35 M 85 SKR 8B-NH8-646-010 C-IC,LC877264V-5Y59 87-012-286-080 CAP,U 0.01-25 K B 87-A21-831-010 IC,SPS-422-1-F1 87-A12-072-080...
Page 22
http://www.xiaoyu163.com IC BLOCK DIAGRAM 3 7 6 3 1 5 1 5 0 1 3 9 4 2 2 9 6 5 1 3 w w w u 1 6 3 – 22 – http://www.xiaoyu163.com...
Page 23
http://www.xiaoyu163.com LCD DISPLAY LCD, AIW4276 - 30PIN SEGMENT WIRING 3 7 6 3 1 5 1 5 0 COMMON WIRING 1 3 9 4 2 2 9 6 5 1 3 w w w u 1 6 3 23 http://www.xiaoyu163.com...
Page 24
http://www.xiaoyu163.com IC DESCRIPTION IC, LC877264V-5Y59 3 7 63 1515 0 Pin No. Pin Name Description O-CD CLK CD IC control clock output. O-LEDSTB STB signal make clock and data effective. O-DATA Data output. O-CLK Clock output. O-CDDATA CD IC control data output. O-INI-SCAN Initial scan output.
Page 25
http://www.xiaoyu163.com 3 7 63 1515 0 Pin No. Pin Name Description 56 ~ 79 O-S25 ~ O-S48 LCD segment S25 ~ S48 output. I-CST2 DECK cassette detection switch data input. "L" : ON. I-REB DECK side B recordable switch. "L" : REC. I-CAM2 DECK CAM switch data input.
Page 26
http://www.xiaoyu163.com ADJUSTMENT <TUNER / DECK / FRONT > < TUNER SECTION > 3 7 63 1515 0 1. Clock Frequency Check 6. SW Tracking Adjustment Settings : • Test point : TP2 (CLK) Settings : • Test point : TP8 (Lch), TP9 (Rch) •...
http://www.xiaoyu163.com CD TEST MODE 3 7 63 1515 0 1. How to Start the CD Test Mode While pressing the FUNCTION button, insert the AC plug to the power outlet. When the test mode is started, the message [TEST] is displayed. 2.
Page 29
http://www.xiaoyu163.com 3 7 63 1515 0 4. Displaying the Adjustment Result of the Automatic Adjustment Items The automatic adjustment values of the focus and tracking adjustment can be displayed on the screen. 4-1. Displaying the automatic adjustment result for the focus offset cancel and gain 1.
http://www.xiaoyu163.com GENERAL SPEAKER DISASSEMBLY INSTRUCTIONS (FOR REFERENCE) 3 7 63 1515 0 Type.1 Type.4 Insert a flat-bladed screwdriver into the position indicated by the TOOLS arrows and remove the panel. Remove the screws of each speaker 1 Plastic head hammer unit and then remove the speaker units.