Advertisement
Audio Source Selection
INITIAL OPERATION OF THE SYSTEM REQUIRES:
• All STATION STATUS switches set to RADIO/ IP mode.
• SYSTEM VOLUME set to approximately 1/3 level.
• MASTER VOLUME set to approximately 2/3 level.
• REMOTE STATION VOLUME set to approximately 2/3 level.
RADIO OPERATION
1. Press the PROGRAM ON/OFF key.
2. Select AM or FM by pressing the PROGRAM SELECT key until the desired mode is
displayed in the LCD display.
3. Tune the radio to the desired frequency using one of the following methods:
• RAPID TUNE: Depress and hold either the
frequency you desire. Release the tuning key.
• STEP TUNE: Momentarily touch either the L or M tuning keys, and the radio will tune
to the next radio frequency.
• SCAN: Momentarily touch SCAN key. The radio tunes up in frequency to the next
strong signal. It remains on this signal for five (5) seconds, then moves to the next
strong signal. When the desired station is found, press the SCAN key to stop the scan
operation.
RADIO MEMORY
4 AM and 4 FM radio frequencies may be stored in the system's memory for recall by
using the following procedure.
STORING FREQUENCIES INTO MEMORY
NOTE: It is recommended that the lowest frequency be programmed into memory 1 and
the next higher frequency into memory 2, etc.
1. Select the radio to FM and tune to the desired frequency using the LM or SCAN
keys.
2. Press the MEMORY SET key (behind panel door). Within 5 seconds, press the
MEMORY RECALL key until the desired memory channel to store the current radio
frequency into is shown in the LCD display. Within 5 seconds, again press the
MEMORY SET key and the frequency will be stored.
3. Repeat this procedure for all four FM memory channels.
4. Select the radio to AM and repeat the programming procedure for the AM MEMORY
CHANNELS.
NOTE: During a power outage, the radio memory channels will be lost.
6
L or M tuning keys until you reach the
RECALLING FREQUENCIES
1. Select AM or FM mode.
2. Press the MEMORY RECALL key until desired memory channel is shown in the
LCD display.
CONTROLLING THE RADIO FROM REMOTE SPEAKERS
The remote stations can be used to turn the radio ON/OFF and advance the radio
memory channels.
NOTE: Remote control of the Radio will not function during intercom communication.
Remote control of the Radio will not function if the master has been selected to
CD/TAPE program position.
TURNING THE RADIO ON AND OFF
1. The radio may be turned on or off from a remote station by pressing and holding the
END CALL key for two (2) seconds. After the radio turns on/off, release the END
CALL key.
2. During the time the END CALL key is pressed an "IU" (in use) will be displayed in
the master LCD display. This indicates a remote control function is being performed
at a remote station.
ADVANCING THE RADIO MEMORY CHANNELS
NOTE: Radio memories must be stored before controlling radio memory channels from
remote stations.
The radio memory channels may be advanced from a remote station by momentarily
pressing the END CALL key.
1. Select the master station to radio using the PROGRAM SELECT key on the master
station, or END CALL key at a remote station.
2. Pressing the END CALL key momentarily will advance the memory channel to the
next highest stored memory channel.
3. Continue pressing the END CALL key to advance to the next highest stored memory
channel.
4. After reaching the highest stored memory channel in the current program mode (AM
or FM), momentarily pressing the END CALL key will cause program mode (AM or
FM) to switch to the opposite mode and select the lowest programmed memory
channel.
5. Continuing to momentarily press the END CALL key will repeat the operation.
CD/TAPE AUXILIARY SELECTION
An optional audio source may be selected by using the following procedure:
1. Press the PROGRAM ON/OFF key to turn on the program audio.
2. Press the PROGRAM SELECT key until CD/TAPE is shown in the LCD display. If an
optional audio source (tape player/CD player) has been connected to your unit, this
unit will be heard as the audio source. The optional CD/TAPE audio throughout the
system may be turned off by pressing the PROGRAM ON/OFF key.
7
Advertisement
