Panasonic AG-DVX100A Operating Instructions Manual page 46

Setting menus
RECORDING SETUP screen
Item/
Description of settings
(display mode)
1394 TC REGEN For selecting the time code to be recorded
(VCR) when recording the signals of a component
connected to the DV connector.
OFF:
The signals are recorded using the time
code which was set using the TC MODE
item, TCG item and FIRST REC TC
item.
ON:
The signals are recorded using the time
code of the signals which have been
input to the DV connector.
O When ON has been selected as this
item's setting,
precedence over the TC MODE item,
TCG item and FIRST REC TC item
settings.
O When no signals are supplied to the DV
connector, the TC MODE item, TCG item
and FIRST REC TC item settings are
followed.
TC MODE For selecting the time code correction
(Camera) mode in which the time code of the internal
(VCR) time code generator is to be recorded.
DF : The drop frame mode is used.
NDF : The non-drop frame mode is used.
O When the progressive mode has been
set to 24P or 24P (ADV), the non-drop
frame mode is established regardless of
this item's setting.
TCG For setting the operation mode in which the
(Camera) internal time code generator is to be run.
(VCR) FREE RUN:
The internal time code generator is run
regardless of the operation mode.
REC RUN:
The internal time code generator is run
during recording.
FIRST REC TC For selecting the time code which is to be
(Camera) recorded when recording is started.
(VCR) REGEN:
Recording proceeds in such a way that
the time
regenerated) from the time code on the
tape.
PRESET:
The time code is not regenerated from
the time code on the tape.
The time code is recorded using the
value set in the TC PRESET item
serving as the initial value.
However, the time code is forcibly
regenerated when shooting with frame-
to-frame continuity has been performed.
The underlining indicates the factory setting.
46
this setting takes
code continues on (is
Item/
Description of settings
(display mode)
TC PRESET For setting the initial value of the time code
(Camera) to be recorded.
(VCR) This item's setting is valid when PRESET
has been selected as the setting for the
FIRST REC TC item.
O When the progressive mode has been
set to 24P or 24P (ADV), set the frame
value to 0 or to a multiple of 5. If any
other value is set, the time code
recorded will shift.
1394 UB REGEN For selecting the user's bit to be recorded
(VCR) when recording
component connected to the DV connector.
OFF:
The user's bit selected for the UB MODE
item is used for the recording.
ON:
The user's bit of the signals input to the
DV connector is used for the recording.
O When ON has been selected as this item's
setting, this setting takes precedence over
the UB MODE item setting.
O The user's bit is not recorded if the
signals do not contain the user's bit
information.
O When no signals are supplied to the DV
connector, the UB MODE item setting is
followed.
UB MODE For setting what is to be recorded as the
(Camera) user's bit.
(VCR) USER:
The user's information is recorded.
TIME:
The time of the recording is recorded.
DATE:
The date of the recording is recorded.
TCG:
The time code generator's value is
recorded.
FRM. RATE:
The frame rate information for frame
conversion is recorded.
22 02 22 22
Frame rate information
O Frame rate (60, 30 or 24)
O I/P identification information
O Conversion information
O Frame rate coefficient
Frame sequence number
O A number from 0 to 4 is displayed
in the 24P or 24P (ADV) mode.
O "F" is displayed in the 60 or 30P
mode.
User's bit value verification
information
the signals of the
Recording control
information
O Updated frame information
O REC START/STOP
information