Making Coffee; Preparing Hot Water; Heating Liquids With Steam; Preparing Milk Froth - Nespresso Romeo Instructions For Use Manual

Making coffee

Tip : To ensure a successful espresso coffee,
prewarm the cups on the warming plate 6
or fill the cups with hot water and rinse out.
The appliance must be switched on, Ready
is indicated on Display 5.
G
Place a NESPRESSO – capsule with
®
the membrane face down on the ledge
20 (Fig. 2).
G
Place a prewarmed cup under the coffee
outlet 18.
G
Press button 2 or button 3 depend-
ing on the cup size. The cup is filled.
The coffee outlet stops automatically
when the programmed amount has
run through.
Ready is indicated again on display 5.
After use the capsule is automatically
.
conveyed into the capsule container 15
Stopping the coffee outlet early
G
Press button 2 or button 3 again.
Permanently changing the
amount of liquid
The preset amount for a small or large cup
can be changed.
G
Hold down button 2 or button 3
until the required amount of coffee has
run through.
The amount can be changed again at
any time.
Additional amount of liquid
G
Press button 2 or button 3 again
within four seconds after the coffee outlet
has stopped.
The same amount of water is conveyed
again by the capsule.
Making coffee or drawing
water immediately after
drawing steam
If coffee is drawn immediately after steam
has been drawn by pressing button 2 or
button 3, the appliance automatically
cools down beforehand. First the appliance
gives off steam at intervals, then the coffee
flows out of the coffee outlet 18.
If hot water is to be drawn immediately
after steam has been drawn, cool down the
appliance beforehand by pressing button
4, the appliance gives off steam into the
drip tray 14.

Preparing hot water

Hot water can be prepared with this func-
tion, e.g. for a cup of tea.
Risk of burns
The nozzle becomes very hot, hold the
nozzle by the plastic part only.
G
Screw the nozzle 13 onto the adapter
11 of the steam pipe 10 (Fig. 3).
G
Hold a glass or a cup under the nozzle 13.
4
G
Put the hot water/steam lever 9 in a hori-
zontal position.
Hot water runs out of the nozzle 13.
G
To stop the hot water, put the hot
water/steam lever 9 back in the upright
position.
Wait is indicated briefly on display 5.
Ready is indicated again on display 5.

Heating liquids with steam

Risk of scalding
Steam is very hot. It may cause the liquid to
splash.
G
Screw on the nozzle 13 (Fig. 3).
G
Press button 4.
Steam and Wait flash alternately on dis-
play 5.
As soon as Steam and Ready flash alter-
nately on display 5, steam can be drawn.
G
Immerse the nozzle 13 deep into the liq-
uid, but do not touch the bottom of the
vessel.
G
Put the hot water/steam lever 9 in a hori-
zontal position (Fig. 4).
G
Slowly rotate the vessel.
The liquid is heated.
G
When the liquid is hot, put the hot
water/steam lever 9 back in the upright
position.
Steam and Ready are indicated alternately
on display 5.
The appliance now automatically cools
down for approx. 1 minute. Ready is indi-
cated again on display 5.
Clean the nozzle 13 as soon as it has
cooled down. Dried residue is difficult to
remove. See the chapter on «Care and
daily cleaning».

Preparing milk froth

Frothing or heating milk
Risk of scalding
The steam is very hot.
Handle the frothing device by the plastic
part only.
G
Firmly fit together the frothing device for
CAPPUCCINO/CAFFELATTE 12 (Fig.
5/a). There must be no gaps.
G
Connect the frothing device 12 firmly to
the adapter 11 on the steam pipe 10
(fig. 5/b).
G
Immerse the hose into a vessel contain-
ing milk.
G
Move the selector on the frothing device
12 either to CAPPUCCINO (milk froth) or
CAFFELATTE (hot milk).
G
Place a cup or a glass under the nozzle
of the frothing device 12.
G
4.
Press button
G
When Steam and Ready flash alternately
on display 5, put the hot water/steam
lever 9 in a horizontal position.The milk
is drawn in, heated and frothed.
5