Download Print this page

Travis Industries 564 HO Installation Instructions Manual

Hide thumbs Also See for 564 HO:

Advertisement

Packing List
Burner Assembly
Grate Assembly
Log Set
Intake Restrictor
Installation Tips
If using propane (LP), convert the appliance before installing the burner.
Make sure to have the firebacks for the appliance on hand. They will be
installed during burner installation.
Installation Warnings
The logs are fragile, especially after being exposed to heat.
Make sure the gas control valve is OFF and the heater is cool before
servicing.
Failure to position the parts in accordance with these diagrams or failure to
use only parts specifically approved with this appliance may result in
property damage or personal injury.
The burner must be correctly positioned before installing the logs. Make sure
the burner is fully seated and the pilot is properly aligned.
Andiron Clips
NOTE: Two andiron clips are included for
those installations using andirons. See the
directions to the right to install.
Page 1 of 9
564 HO Ember-Fyre Burner and Log Set
Installation Instructions
17601655 — 11/14/12
(sku 96900116)
Air Deflectors, NG and LP
(2) Andiron Clips
(2) Rivets for burner
Burner Support Bracket
Bag of embers
11/32" Nutdriver
a
b
5/32 Hex
Wrench
c
© Travis Industries, Inc.

Advertisement

loading

Summary of Contents for Travis Industries 564 HO

  • Page 1 564 HO Ember-Fyre Burner and Log Set Installation Instructions (sku 96900116) Packing List   Burner Assembly Air Deflectors, NG and LP   Grate Assembly (2) Andiron Clips   Log Set (2) Rivets for burner   Intake Restrictor Burner Support Bracket ...
  • Page 2 564 HO Ember-Fyre Burner and Log Set Installation Instructions (sku 96900116) Log Set Installation 1. Remove both accent lights from the brackets and place them on the firebox floor, as shown below. 2. Install the burner support bracket, as shown below.
  • Page 3 564 HO Ember-Fyre Burner and Log Set Installation Instructions (sku 96900116) 4. Install the firebacks as shown below. Remove the clip located on the firebox ceiling near the front (both sides). The side fireback clip has a keyhole slot. It can be removed by loosening the screw and sliding the clip out.
  • Page 4 564 HO Ember-Fyre Burner and Log Set Installation Instructions (sku 96900116) 5. Replace the Accent Lights. The fireplace should now look as shown below. 6. Install the burner inside the firebox. 7. Install the grate on top of the burner. Note how the grate slides into metal clips on the sides of the burner.
  • Page 5 564 HO Ember-Fyre Burner and Log Set Installation Instructions (sku 96900116) 8. Install the correct air deflector as shown below. Note how the dimple inserts into a slot on the burner (“a”). Figure 1: Deflector Replacement 9. Install the rivets on the burner as shown below.
  • Page 6 564 HO Ember-Fyre Burner and Log Set Installation Instructions (sku 96900116) 10. Install the Rear Log onto the 2 pins at the rear of the firebox, as shown below. The log rests against the back wall or fireback. NOTE: NG and LP configurations require different log placement settings. For NG pull the rear log forward for maximum glow.
  • Page 7 564 HO Ember-Fyre Burner and Log Set Installation Instructions (sku 96900116) 12. Install the Right Log onto the 2 pins at the right of the firebox, as shown below. Note how the two pins on the burner insert into the holes on the log.
  • Page 8 564 HO Ember-Fyre Burner and Log Set Installation Instructions (sku 96900116) 14. Install the Right Log Chunk as shown below. Note how it rests on the grate and fireback. Figure 19: Right Log Chunk Location Figure 20: Right Log Chunk Installed Figure 21: Right Log Chunk –...
  • Page 9 564 HO Ember-Fyre Burner and Log Set Installation Instructions (sku 96900116) 16. Install the Right Twig as shown below. Note how the flat side of the twig fits on the right log and the pin on the rear log. Figure 27: Right Twig Pin Figure 28: Right Twig Installed Figure 29: Right Twig –...