Sony STR-DA5400ES Service Manual page 23

SPECIAL MENU MODE
Procedure:
1. Press the [POWER] button to turn on the main power, then while pressing the [TONE MODE] button, press the [A.F.D.], [2CH/A.
DIRECT], [MUSIC], [MOVIE] button in order, the message "MENU SPECIALIZED!" appears.
2. Press the [ ]/[ ] buttons of the remote commander, the message "<<< SPECIAL >>>" appears.
M m
3. Press the [ ] button of the remote commander, the item is appears.
,
4. Each time the [ ]/[ ] buttons of the remote commander is pressed, the item is switched in order as follows.
M m
Some items can change the content. Display the cursor by pressing the [
by pressing the [ ]/[ ] buttons of the remote commander, and fi x the content by pressing the [
M m
when you want to change the content of the item.
5. To release from this mode, while pressing the [TONE MODE] button, press the [A.F.D.], [2CH/A. DIRECT], [MUSIC], [MOVIE] but-
ton in order again, the message "MENU SPECIALIZED OFF" appears.
Items
SYSTEM version display
MAIN Ucom version display
Video Ucom version display
FAROUDJA version display
FAROUDJA (2nd) version display
GUI CG-ROM version display
DSP Ucom version display
DSP serial fl ash version display
DSP parallel fl ash version display
DSP debug menu
FAROUDJA update
HDCP key read
Model/destination change
Video factory menu
Video calibration
(Video factory menu)
DDR access check
Auto cal mic test
FL display fonts test
FL display test
Super reset
RAM watch menu
Display
SYSTEM VERSION X.XXX
MAIN ##### ∗∗∗ vX. XX
Video Ucom Ver X. XX
FAROUDJA Ver X. XX
FAROUDJA2ND Ver X. XX
GUI CGROM Ver X. XX
DSP Ucom Ver X. XX
DSP SFLASH Ver X. XX
DSP PFLASH Ver X. XX
<DSP DEBUG MENU>
FAROUDJA UPDATE [XXX]
HDCP KEY READ [XXX]
MODEL [##### ∗∗∗∗ XX]
<VIDEO FACTORY MENU>
V.CALIBRATION START?
DDR CHECK [XX] sec
SPEAKER OUT [XXXXX]
FL FONT [0x ∗∗ = X]
ALL ON
SUPER RESET [XXX]
XXX
] button of the remote commander, and changing the content
,
] button of the remote commander
<
Remark
X.XXX: System software version
#####: Model
∗∗∗: Destination
X.XX: Main controller software version
X.XX: Video system controller software version
X.XX: Video processor software version (main zone)
X.XX: Video processor software version (2nd zone)
X.XX: CG-ROM software version
X.XX: DSP controller version
X.XX: Serial fl ash software version
X.XX: DSP parallel fl ash version
Not used for the servicing
XXX: ON or OFF
Not used for the servicing
Not used for the servicing
Menu mode to enter video calibration menu and DDR access
check menu If the [ENTER] button of the remote commander
is pressed, entering the menu, and operating two the following
menu become possible
Procedure:
1. "DVD" is selected by using [INPUT SELECTOR] dial.
2. Connect a color pattern generator to the COMPONENT
VIDEO ASSIGNABLE (INPUT ONLY) IN2 jack (J6007) on
the A-VIDEO board and DVD VIDEO IN jack (J6003) on the
A-VIDEO board.
3. Input 100% color bars signal from the color pattern generator.
4. Menu that measures individual difference of hardness by
automatic operation in pressing the [ENTER] button of the
remote commander, and corrects reference value. In a mea-
surement once, only one of NTSC/PAL/HD can be measured,
repeat NTSC/PAL/HD calibration from procedure 4.
"Check XXXX V-IN" at display:
Video signal necessary for the measurement while measuring
it last time was not detected and it became an error
Confi rm the input of the video of the terminal connection etc.,
and measure the [ENTER] button of the remote commander
again pressing
XX: Time to do access check on DDR (for design evaluation)
(Video factory menu)
XXXXX: Selection of speaker output audio [SOURCE]: nomally
mode, [MIC]: mode that output audio from mic from speaker
∗∗: 20 to FE, X: character
Each time [DISPLAY] button to change as follows all on t
test pattern 1 t test pattern 2 t all off t all on
Not used for the servicing
If super reset is performed, "up convert signal level adjustment"
will also be initialized
When EEPROM initialization is required, perform the "memory
clearing mode"
Not used for the servicing
STR-DA5400ES
23