Page 1 When it comes to service, remember that your Toyota dealer knows your vehicle best and is interested in your complete satisfaction. He will provide quality maintenance and any other assistance you may require. If there is not a Toyota dealer near you, or you need emergency assistance for any reason, please call the following number: U.S. OWNERS: Toyota Customer Assistance Center Toll–free:1–800–331–4331...
Page 2: Important Information About This Manual
03 07.07 Important information about this manual Safety and vehicle damage warnings Safety symbol Throughout this manual, you will see safety and vehicle damage warnings. You must follow these warnings carefully to avoid possible injury or damage. The types of warnings, what they look like, and how they are used in this manual are explained as follows: CAUTION This is a warning against anything which may cause...
Page 3: Occupant Restraint Systems
None of these systems, either indi- Toyota encourages you and your family to take the time vidually or together, can ensure that there is no injury to read Section 1–3 of this Owner’s Manual carefully.
Page 4 New vehicle warranty with tremendous speed. The rapid deployment of the SRS airbags makes the SRS airbags themselves poten- Your new vehicle is covered by the following Toyota tial sources of serious injury if an occupant is too close limited warranties:...
Page 5 SRS airbag system and seat belt pretensioner may cause to, or adverse effect they may have on, system, be sure to check with your Toyota dealer for your Toyota vehicle. precautionary measures or special instructions regarding installation.
Page 6 SRS airbag and seat belt pretensioner removed and disposed of by a qualified service shop or by your Toyota dealer before you dis- pose of your vehicle. 2003 MR2 from Aug. ’03 Prod. (OM17511U)
Page 7 03 07.07 U−6 Quick index D If a service reminder indicator or warning buzzer comes on ..D If your vehicle will not start ........D If your engine stalls while driving .
Page 8 03 07.07 SECTION – OPERATION OF INSTRUMENTS AND CONTROLS Overview of instruments and controls Instrument panel overview ........Instrument cluster overview .
Page 9 03 07.07 Instrument panel overview 1. Side vents 2. Instrument cluster 3. Center vents 4. Interior light 5. Glove box 6. Manual transmission gear shift lever or sequential manual transmission selector lever 7. Parking brake lever 8. Power window switches 9.
Page 10 03 07.07 1. Headlight and turn signal switches 2. Transmission shift switches (with sequential manual transmission) 3. Wiper and washer switches 4. Clock 5. Rear window defogger switch 6. Emergency flasher switch 7. Auxiliary box 8. Engine immobilizer system indicator light 9.
Page 11 03 07.07 Instrument cluster overview SB11023a 1. Speedometer 4. Engine coolant temperature gauge 7. Tachometer 2. Service reminder indicators and indica- 5. Low fuel level warning light 8. Trip meter reset knob tor lights 6. Fuel gauge 9. Odometer and two trip meters 3.
Page 12 03 07.07 Indicator symbols on the instrument panel ∗ 1 ∗ 1 Brake system warning light SRS warning light ∗ 1 ∗ 1 Driver’s seat belt reminder light Power steering system warning light ∗ 1 ∗ 1 Sequential manual transmission warning light Passenger’s seat belt reminder light ∗...
Page 13 03 07.07 2003 MR2 from Aug. ’03 Prod. (OM17511U)
Page 14: Table Of Contents
03 07.07 SECTION OPERATION OF INSTRUMENTS AND CONTROLS Keys and Doors Keys ............Engine immobilizer system .
Page 15: Keys
When using a key containing a trans- 1. Master keys (black)—These keys work ponder chip, observe the following in every lock. Your Toyota dealer will need one of them to make a new key precautions: with a built- in transponder chip.
Page 16 03 07.07 z Do not cover the key grip with any material that cuts off electromagnet- ic waves. z Do not knock the key hard against other objects. SY12002a SY12003 z Do not leave the key exposed to high temperatures for a long period, such as on the dashboard and hood under the direct sunlight.
Page 17: Engine Immobilizer System
Toyota dealer. need additional keys, duplicates can be the electronic code in the chip corre- made by a Toyota dealer using the key The indicator light stays on. sponds to the registered ID code for number.
Page 18: Side Doors
03 07.07 Side doors For your Toyota dealer to make you a For vehicles sold in U.S.A. new key with built- in transponder chip, your dealer will need your key number FCC ID: MOZ RI- 8FTY and master key. However, there is a limit MADE IN.
Page 19 03 07.07 CAUTION Before driving, be sure that the doors closed locked, especially when small children are in the ve- SB12035 SB12080a hicle. Along with the proper use of seat belts, locking the doors helps prevent the driver and passengers from being thrown out from the ve- hicle during an accident.
Page 20: Power Windows
03 07.07 Power windows SB12049 SB12050 SB12090 The windows can be operated with the Automatic operation open only): OPERATING PASSENGER’S switch on the center console. Push the switch completely down and then WINDOW release it. The window will fully open. To The power windows work when the ignition Use the switch on the passenger’s side stop the window partway, lightly pull the...
Page 21 03 07.07 CAUTION Be sure to remove the ignition key or turn the ignition switch to the To avoid serious personal injury, you “LOCK” position when you leave must do the following. your vehicle. Before you close the power win- Never leave anyone (particularly a SB12081a dows, always make sure there is...
Page 22: Trunk Lid
03 07.07 Trunk lid— SB12043 SB12037a SB12068a Front box cover To open the trunk lid: 2. In front of the vehicle, pull up the 3. Hold the trunk lid open by inserting auxiliary catch lever and lift the support rod into the slot. 1.
Page 23: Engine Hood
03 07.07 —Luggage security system Engine hood CAUTION After inserting the support rod into the slot, make sure the rod sup- ports the trunk lid securely from SB12091 SB12086a falling down on to your head or body. Before closing the trunk lid, lock the front box cover securely.
Page 24 03 07.07 CAUTION After inserting the support rod into the slot, make sure the rod supports the engine hood securely from falling SB12044a SB12038a down on to your head or body. NOTICE Be sure to return the support rod to its clip before closing the engine hood.
Page 25: Fuel Tank Cap
03 07.07 Fuel tank cap SB12087 SD12013a SB12088a LOCKING UNLOCKING WITH This indicates that the fuel filler door 1. To open the fuel filler door, pull the ENGINE HOOD is on the left side of your vehicle. lever up. When refueling, turn off the engine. To lock: Turn the key clockwise.
Page 26 Make sure the cap is tightened securely. The indicator lamp goes off after driving several times. If the indicator lamp does not go off, contact your Toyota dealer as soon as possible. 2003 MR2 from Aug. ’03 Prod. (OM17511U)
Page 27: Soft Top
03 07.07 Soft top— —Soft top precautions Sequential manual transmission: Before NOTICE raising or lowering the soft top, lower both side windows, apply the parking brake, put z Make sure there are no items or the selector lever in the “S(1)” position packages in the folding board when and stop the engine.
Page 28 03 07.07 —Lowering the soft top z When the soft top is completely lowered, keep the rear window de- fogger turned off to avoid damage to the top. z It may be hard to fix the soft top SB12077 SB12071a when raising it after having kept it open for a long time.
Page 29 03 07.07 SB12072 SB12082a SB12079a 3. Lower the soft top backward press- 4. Fold the soft top slowly and house CAUTION ing the rear window glass down soft- it completely. Press down the soft top toward the front To prevent personal injury, do not from the rear and lock it.
Page 30 03 07.07 —Air deflector —Raising the soft top Folding board SB12059a SB12060a SB12061 Flare The air deflector will reduce the wind 1. Lower both side windows and sun NOTICE from the rear of the vehicle when the visors. Then pull down the lock re- vehicle is running with the soft top lease lever towards the front of the z Do not lower the soft top while...
Page 31 03 07.07 SB12074a SB12082a SB12083 2. Stand outside of the vehicle and pull 3. Be seated in the seat and hold the CAUTION the soft top out slowly holding the handle on the center of the front part shown in dark color in the il- soft top frame.
Page 32 03 07.07 Hook on body side Hook on body side SB12078 SB12089 Lock 4. Keep pressing the soft top against If the lock is not hung easily, give your the frame of the front window glass hand to the lock for helping to hang it and fix the soft top by pushing up on the hook on the body side.
Page 33 03 07.07 2003 MR2 from Aug. ’03 Prod. (OM17511U)
Page 34 03 07.07 SECTION – OPERATION OF INSTRUMENTS AND CONTROLS Keys and Doors Keys ............Engine immobilizer system .
Page 35: Keys
When using a key containing a trans- 1. Master keys (black)—These keys work in every lock. Your Toyota dealer will ponder chip, observe the following precautions: need one of them to make a new key with a built–in transponder chip.
Page 36 03 07.07 z Do not cover the key grip with any material that cuts off electromagnet- ic waves. z Do not knock the key hard against other objects. SY12002a SY12003 z Do not leave the key exposed to high temperatures for a long period, such as on the dashboard and hood under the direct sunlight.
Page 37: Engine Immobilizer System
Toyota dealer. need additional keys, duplicates can be the electronic code in the chip corre- made by a Toyota dealer using the key The indicator light stays on. sponds to the registered ID code for number.
Page 38: Side Doors
03 07.07 Side doors For your Toyota dealer to make you a For vehicles sold in U.S.A. new key with built–in transponder chip, your dealer will need your key number FCC ID: MOZ RI–8FTY and master key. However, there is a limit MADE IN.
Page 39 03 07.07 CAUTION Before driving, be sure that the doors closed locked, especially when small children are in the ve- SB12035 SB12080a hicle. Along with the proper use of seat belts, locking the doors helps prevent the driver and passengers from being thrown out from the ve- hicle during an accident.
Page 40: Power Windows
03 07.07 Power windows SB12049 SB12050 SB12090 The windows can be operated with the Automatic operation open only): OPERATING PASSENGER’S switch on the center console. Push the switch completely down and then WINDOW release it. The window will fully open. To The power windows work when the ignition Use the switch on the passenger’s side stop the window partway, lightly pull the...
Page 41 03 07.07 CAUTION Be sure to remove the ignition key or turn the ignition switch to the To avoid serious personal injury, you “LOCK” position when you leave must do the following. your vehicle. Before you close the power win- Never leave anyone (particularly a SB12081a dows, always make sure there is...
Page 42: Trunk Lid
03 07.07 Trunk lid— SB12043 SB12037a SB12068a Front box cover To open the trunk lid: 2. In front of the vehicle, pull up the 3. Hold the trunk lid open by inserting auxiliary catch lever and lift the support rod into the slot. 1.
Page 43: Engine Hood
03 07.07 —Luggage security system Engine hood CAUTION After inserting the support rod into the slot, make sure the rod sup- ports the trunk lid securely from SB12091 SB12086a falling down on to your head or body. Before closing the trunk lid, lock the front box cover securely.
Page 44 03 07.07 CAUTION After inserting the support rod into the slot, make sure the rod supports the engine hood securely from falling SB12044a SB12038a down on to your head or body. NOTICE Be sure to return the support rod to its clip before closing the engine hood.
Page 45: Fuel Tank Cap
03 07.07 Fuel tank cap SB12087 SD12013a SB12088a LOCKING UNLOCKING WITH This indicates that the fuel filler door 1. To open the fuel filler door, pull the lever up. ENGINE HOOD is on the left side of your vehicle. When refueling, turn off the engine. To lock: Turn the key clockwise.
Page 46 Make sure the cap is tightened securely. The indicator lamp goes off after driving several times. If the indicator lamp does not go off, contact your Toyota dealer as soon as possible. 2003 MR2 from Aug. ’03 Prod. (OM17511U)
Page 47: Soft Top
03 07.07 Soft top— —Soft top precautions Sequential manual transmission: Before NOTICE raising or lowering the soft top, lower both side windows, apply the parking brake, put z Make sure there are no items or the selector lever in the “S(1)” position packages in the folding board when and stop the engine.
Page 48 03 07.07 —Lowering the soft top z When the soft top is completely lowered, keep the rear window de- fogger turned off to avoid damage to the top. z It may be hard to fix the soft top SB12077 SB12071a when raising it after having kept it open for a long time.
Page 49 03 07.07 SB12072 SB12082a SB12079a 3. Lower the soft top backward press- 4. Fold the soft top slowly and house CAUTION ing the rear window glass down soft- it completely. Press down the soft top toward the front To prevent personal injury, do not from the rear and lock it.
Page 50 03 07.07 —Air deflector —Raising the soft top Folding board SB12059a SB12060a SB12061 Flare The air deflector will reduce the wind 1. Lower both side windows and sun NOTICE from the rear of the vehicle when the visors. Then pull down the lock re- vehicle is running with the soft top lease lever towards the front of the z Do not lower the soft top while...
Page 51 03 07.07 SB12074a SB12082a SB12083 2. Stand outside of the vehicle and pull 3. Be seated in the seat and hold the CAUTION the soft top out slowly holding the handle on the center of the front part shown in dark color in the il- soft top frame.
Page 52 03 07.07 Hook on body side Hook on body side SB12078 SB12089 Lock 4. Keep pressing the soft top against If the lock is not hung easily, give your the frame of the front window glass hand to the lock for helping to hang it and fix the soft top by pushing up on the hook on the body side.
Page 53 03 07.07 2003 MR2 from Aug. ’03 Prod. (OM17511U)
Page 54 03 07.07 SECTION – OPERATION OF INSTRUMENTS AND CONTROLS Occupant restraint systems Seats ............Seat belts .
Page 55 03 07.07 —Seat precautions Seats— While the vehicle is being driven, all ve- Driver seat Slightly recline the back of hicle occupants should have the seatback seat. Although vehicle designs vary, upright, sit well back in the seat and prop- CAUTION many drivers can achieve the 250 erly wear the seat belts provided.
Page 56 03 07.07 —Seat adjustment precautions Passenger seat CAUTION While adjusting the seat, do not put your hands under the seat or near CAUTION Do not adjust the seat while the the moving parts. Otherwise, you vehicle is moving as the seat may may jam your hands or fingers may The SRS passenger airbag also de- unexpectedly move and cause the...
Page 57 03 07.07 —Adjusting seats 1. SEAT POSITION ADJUSTING LEVER 3. SEAT CUSHION ANGLE ADJUSTING KNOB (driver’s seat only) Hold the center of the lever and pull it up. Then slide the seat to the desired Turn the knob either way. position with slight body pressure and release the lever.
Page 58 03 07.07 Seat belts— —Seat belt precautions Toyota strongly urges that the driver and Pregnant woman. Toyota recommends the To reduce the risk of sliding under passenger in the vehicle be properly re- use of a seat belt. Ask your doctor for...
Page 59 It also may normally, immediately contact your lock if you lean forward too quickly. A Toyota dealer. Do not use the seat slow, easy motion will allow the belt to until the seat belt is fixed, because extend, and you can move around freely.
Page 60 03 07.07 CAUTION Both high–positioned lap belts and Take up Take up slack loose–fitting belts could cause seri- slack ous injuries due to sliding under Too high Too high SB13069 SB13070 the lap belt during a collision or other unintended event. Keep the lap belt positioned as low on hips as possible.
Page 61 Toyota dealer free of extender. charge. Do not use the seat belt extender Please contact your local Toyota dealer to SB13071 when installing child restraint order the proper required length for the system on the passenger seat.
Page 62 The driver and passenger seat belt pre- The seat belt pretensioner system con- Toyota dealer. Do not use the seat tensioners are designed to be activated sists mainly of the following components until the seat belt is fixed, because in response to a severe frontal impact.
Page 63 Attachment of a grille guard (bull result in death or serious injury. Con- bar, kangaroo bar, etc.), snowplow, airbag sensor assembly, front airbag sen- sult your Toyota dealer about any re- winches or any other equipment to sors, seat belt pretensioner assemblies, pair and modification.
Page 64 The seat belt pretensioner assembly or surrounding area has been damaged. In the following cases, contact your Toyota The SRS (Supplemental Restraint Sys- tem) airbags are designed to provide dealer as soon as possible:...
Page 65 03 07.07 Your vehicle is equipped with a crash CAUTION Improperly seated and/or restrained sensing and diagnostic module, which will infants and children can be killed record the use of the seat belt restraint The SRS airbag system is designed or seriously injured by the deploy- system by the driver when the SRS air- only as a supplement to the prima-...
Page 66 03 07.07 CAUTION Indicator light Make sure that the indicator light is off. Do not turn off the passenger air- SB13106a bag manual on–off switch except when a member of a passenger risk group identified in TABLE 1 is oc- cupying the passenger seating posi- tion.
Page 67 03 07.07 The SRS airbags are designed to deploy TABLE 1: A PASSENGER RISK GROUP in severe (usually frontal) collisions where the magnitude and duration of Infant. An infant (less than 1 year old) who must ride in the front seat because: the forward deceleration of the vehicle Vehicle has no rear seat;...
Page 68 03 07.07 Hitting a curb, edge Falling into or of pavement or hard jumping over Collision from the rear SC13014a SB13077 SB13094a surface a deep hole Collision from the side Landing hard or vehicle falling Vehicle rollover The SRS airbags are generally not de- The SRS airbags may also deploy if a The SRS airbag system consists mainly of signed to inflate if the vehicle is in-...
Page 69 Toyota very quickly fills the airbags with non–tox- to the face, chest, arms and hands. These...
Page 70 03 07.07 SB13053 SB13054 SB13055 Do not sit on the edge of the seat Do not allow a child to stand up or Do not put anything or any part of or lean against the dashboard when kneel on the passenger seat, since your body on or in front of the the vehicle is in use, since the pas- the passenger airbag could inflate...
Page 71 Do not perform any of the following or open any components such as changes without consulting your the steering wheel pad, steering Toyota dealer. Such changes can in- wheel, column cover, dashboard terfere with proper operation of the SB13102a near the passenger airbag, passen- SRS airbag system in some cases.
Page 72 The light comes on or starts flashing while driving. SB13067a SB13106a In the following cases, contact your Toyota This on–off switch is designed to dis- dealer as soon as possible: able the passenger airbag in order to allow usage, if necessary, of a member The SRS airbags have been inflated.
Page 73 03 07.07 Child restraint— —Child restraint precautions The indicator comes on when the passen- Toyota strongly urges the use of ap- CAUTION ger airbag system is off. propriate child restraint systems for children. To check the airbag cut–off system status, Make sure that the indicator light is turn the ignition switch to the “ON”...
Page 74 03 07.07 —Child restraint system A child restraint system for a small Never install infant or child age 1 Do not use the seat belt extender child or baby must be properly re- to 12 in a passenger risk group on when installing child...
Page 75 03 07.07 —Types of child restraint system Child restraint systems are divided into the following 3 types according to the child’s age and size. (A) Infant seat (B) Convertible seat SB13056 SB13048a (C) Booster seat Install the child restraint system following the instructions provided by its manufac- turer.
Page 76 03 07.07 —Installation with seat belt SB13081 SB13101 SB13107a (A) INFANT SEAT INSTALLATION When you put a rear–facing child re- CAUTION straint system which belongs to a pas- An infant seat must be used in rear– senger risk group on the passenger facing position only.
Page 77 1. Run the lap and shoulder belt through Contact your Toyota dealer immedi- or around the infant seat following the ately. install child instructions provided by its manufactur- restraint system on the seat until er and insert the tab into the buckle the seat belt is fixed.
Page 78 03 07.07 SB13058 SB13059 SB13060 2. Fully extend the shoulder belt to put it 3. While pressing the infant seat firmly CAUTION in the lock mode. When the belt is against the seat cushion and seatback, then retracted even slightly, it cannot let the shoulder belt retract as far as Push and pull the child restraint sys- be extended.
Page 79 03 07.07 SB13095 SB13062 SB13101 4. To remove the infant seat, press the (B) CONVERTIBLE SEAT INSTALLATION CAUTION buckle release button and allow the A convertible seat must be used in for- belt to retract completely. The belt will ward–facing or rear–facing position de- Rear–facing child restraint...
Page 80 03 07.07 CAUTION If you must install a rear–facing child restraint system on the pas- senger seat, make sure the passen- SB13107a SB13083a ger airbag manual on–off switch is in the “OFF” position and that the indicator light is on. Forward–facing child restraint sys- tem: forward–facing...
Page 81 2. Fully extend the shoulder belt to put it 3. While pressing convertible seat Contact your Toyota dealer immedi- in the lock mode. When the belt is firmly against the seat cushion and ately. install...
Page 82 03 07.07 SB13086a SB13096 SB13108 4. To remove the convertible seat, press (C) BOOSTER SEAT INSTALLATION CAUTION the buckle release button and allow the A booster seat must be used in for- belt to retract completely. The belt will ward–facing position only. Push and pull the child restraint sys- move freely again and be ready to tem in different directions to be sure...
Page 83 03 07.07 CAUTION forward–facing child restraint system which belongs to a passenger risk group should never be installed SB13107a SB13064 passenger seat with passenger airbag manual on–off switch in the “ON” position, because the passenger airbag could inflate with considerable speed and force. Otherwise the child may be killed or seriously injured in forward seating position.
Page 84 Always make sure the shoulder belt child from death or serious injury. is positioned across the center of Contact your Toyota dealer immedi- child’s shoulder. The belt should be ately. install child SB13097 kept away from child’s neck, but restraint system on the seat until the seat belt is fixed.
Page 85 03 07.07 —Using a top strap SB13110 SB13111 SB13112a Follow the procedure below for a child Use the anchor bracket on the luggage TO USE THE ANCHOR BRACKET restraint system that requires the use trim to attach the top strap. 1.
Page 86 03 07.07 —Installation with child restraint lower anchorages Store a removed cover in a safe place such as the glove box. Be sure to replace a cover when the an- chor bracket is not in use. SB13113 SB13116 2. Fix the child restraint system with The lower anchorages for the child re- the seat belt.
Page 87 03 07.07 CHILD RESTRAINT SYSTEM INSTALLATION Type A— 1. Widen the clearance between seat cushion and seatback a little and confirm the position of the low- er anchorages below the tag in the seatback. 2. Latch the hooks of lower straps onto the anchorages and tighten the lower straps.
Page 88 03 07.07 CAUTION When using the lower anchorages for the child restraint system, be sure that there are no irregular ob- jects around the anchorages or that the seat belt is not caught. Push and pull the child restraint system in different directions to be sure it is secure.
Page 89 03 07.07 2003 MR2 from Aug. ’03 Prod. (OM17511U)
Page 90 03 07.07 SECTION OPERATION OF INSTRUMENTS AND CONTROLS Steering wheel and Mirrors Tilt steering wheel ......... . . Outside rear view mirrors .
Page 91 03 07.07 Tilt steering wheel Outside rear view mirrors— CAUTION Do not adjust the steering wheel while the vehicle is moving. Doing so may cause the driver to mishan- SB13049 SB13050 dle the vehicle and an accident may occur resulting in death or serious injuries.
Page 92 03 07.07 —Power rear view mirror control NOTICE CAUTION If ice should jam the mirror, do not Do not adjust the mirror while the operate the control or scrape the mir- vehicle is moving. Doing so may ror face. Use a spray de- icer to free cause the driver to mishandle the ve- the mirror.
Page 93 03 07.07 Anti- glare inside rear view mirror —Folding rear view mirrors CAUTION Do not adjust the mirror while the vehicle is moving. Doing so may cause the driver to mishandle the ve- SB13051 SB13088 hicle and an accident may occur re- sulting in personal death or injuries.
Page 94 03 07.07 SECTION – OPERATION OF INSTRUMENTS AND CONTROLS Steering wheel and Mirrors Tilt steering wheel ......... . . Outside rear view mirrors .
Page 95 03 07.07 Tilt steering wheel Outside rear view mirrors— CAUTION Do not adjust the steering wheel while the vehicle is moving. Doing so may cause the driver to mishan- SB13049 SB13050 dle the vehicle and an accident may occur resulting in death or serious injuries.
Page 96 03 07.07 —Power rear view mirror control NOTICE CAUTION If ice should jam the mirror, do not Do not adjust the mirror while the operate the control or scrape the mir- vehicle is moving. Doing so may ror face. Use a spray de–icer to free cause the driver to mishandle the ve- the mirror.
Page 97 03 07.07 Anti–glare inside rear view mirror —Folding rear view mirrors CAUTION Do not adjust the mirror while the vehicle is moving. Doing so may cause the driver to mishandle the ve- SB13051 SB13088 hicle and an accident may occur re- sulting in personal death or injuries.
Page 98 03 07.07 SECTION – OPERATION OF INSTRUMENTS AND CONTROLS Lights, Wipers and Defogger Headlights and turn signals ........Emergency flashers .
Page 99: Headlights And Turn Signals
03 07.07 Headlights and turn signals NOTICE To prevent the battery from being dis- charged, do not leave the lights on for a long period when the engine is not running. SB14009a SB14019 Daytime running light system The headlights turn on at reduced intensi- ty when the parking brake is released with the engine started, even with the light switch in the “OFF”...
Page 100: Emergency Flashers
03 07.07 Emergency flashers NOTICE To prevent the battery from being dis- charged, do not leave the switch on longer than necessary when the en- gine is not running. SB14011 SB14012 TURN SIGNALS To turn on the emergency flashers, push the switch. To signal a turn, push the headlight/ turn signal lever up or down to position All the turn signal lights will flash.
Page 101: Front Fog Lights
03 07.07 Front fog lights Instrument panel light control Interior light SB12093 SB14015a SB14022 To turn on the front fog lights, push To adjust the brightness of the instru- To turn on the interior light, slide the the switch. they will come on when the ment panel lights, turn the switch.
Page 102: Windshield Wipers And Washer
03 07.07 Windshield wipers and washer Rear window defogger The “INT TIME” band lets you adjust the wiping time interval when the wiper lever is in the intermittent position (position 1). Twist the band upward to increase the time between sweeps, and downward to decrease it.
Page 103 03 07.07 Make sure you turn the defogger off when the window is clear. Leaving the defogger on for a long time could cause the battery to discharge, especially during stop–and– go driving. The defogger is not designed for drying rain water or for melting snow. NOTICE z To prevent the battery from being discharged,...
Page 104 03 07.07 SECTION – OPERATION OF INSTRUMENTS AND CONTROLS Gauges, Meters and Service reminder indicators Fuel gauge ..........Engine coolant temperature gauge .
Page 105 The indicator lamp goes off after driving several times. If the indicator lamp does Low fuel level not go off, contact your Toyota dealer as warning light soon as possible. The gauge indicates the approximate The gauge indicates the engine coolant...
Page 106 Tachometer Odometer and two trip meters If the engine coolant temperature gauge needle is not displayed, there may be a problem in the system. In this case, con- tact your Toyota dealer as soon as pos- sible. SB15008 SB15005 NOTICE...
Page 107 03 07.07 3. Trip meter reset knob—Resets the two trip meters to zero, and also change the meter display. To change the meter display, quickly push and release the knob. The meter display changes in the order from the odometer to trip meter A to trip meter B, then back to the odometer each time you push.
Page 108 Fill up tank. (See “Fuel gauge” on page 74 in this Section.) Low fuel level warning light Take vehicle to Toyota dealer immediately. If the vehicle cannot be driven, contact your Toyota dealer. 2003 MR2 from Aug. ’03 Prod. (OM17511U)
Page 109 03 07.07 If the indicator or buzzer comes on... Do this. Take vehicle to Toyota dealer. Close both the doors. Take vehicle to Toyota dealer immediately. Take vehicle to Toyota dealer. Key reminder buzzer Remove key. Light reminder buzzer Turn off lights.
Page 110 The engine ignition will continue to oper- ate, however, until the battery is dis- charged. Turn off the air conditioning, blower, radio, etc., and drive directly to the nearest Toyota dealer or repair shop. 2003 MR2 from Aug. ’03 Prod. (OM17511U)
Page 111 03 07.07 (f) Malfunction Indicator Lamp Contact your Toyota dealer as soon as NOTICE possible to service the vehicle. This lamp comes on when the ignition Do not continue driving if the engine key is turned to the “ON” position and If the engine speed does not increase with drive belt is broken or loose.
Page 112 Toyota dealer. Although you may be somewhere in the parts monitored by system. Contact your Toyota dealer as able to drive your vehicle, the vehicle may the warning light system. Contact your soon as possible to service the vehicle.
Page 113 Transmission (sequential ing buzzer does not function as described manual transmission only) above, have it checked by your Toyota dealer as soon as possible. When driving, if any incorrect operation that may cause damage to this system is performed or if the gear is not shifted as...
Page 114 03 07.07 SECTION – OPERATION OF INSTRUMENTS AND CONTROLS Ignition switch, Transmission and Parking brake Ignition switch with steering lock ....... Sequential manual transmission .
Page 115 03 07.07 Ignition switch with steering lock “LOCK”—Engine is off and the steering NOTICE wheel is locked. The key can be re- moved only at this position. Do not leave the key in the “ON” position if the engine is not running. You must push in the key to turn it from “ACC”...
Page 116 03 07.07 Sequential manual transmission The sequential manual transmission is a (a) Selector lever 6–speed forward/reverse transmission. “R”: Reverse With the basics of the traditional manual “N”: Neutral and engine starting transmission, clutch operation and shifting are controlled electronically. The “S”: Sequential driving system has the following features: (normal driving)
Page 117 03 07.07 UP: Upshift switches (Back of the steering wheel) Push the upshift switch on the back of the steering wheel. Every time the switch is operated, the transmission is shifted up 1 step in the order of 1st ³ 2nd ³ 3rd ³ SD16018a 4th ³...
Page 118 03 07.07 (d) Upshift and downshift In case of operating the selector lever and switch operation on the steering wheel at The sequential manual transmission is not the same time, the selector lever opera- an automatic transmission (A/T), therefore, tion has priority. In case of operating the the gears are not shifted automatically.
Page 119 03 07.07 When the outside temperature is ex- Recommended shifting speeds NOTICE tremely low, the gear may not down- For the best compromise between fuel shift from 2nd to 1st until the vehicle If driving at the speed lower than that economy and vehicle performance, you stops.
Page 120 03 07.07 2. With your foot holding down the brake NOTICE CAUTION pedal, shift the selector lever to the “S” position properly. When the selector le- z The system will not allow shifting Be careful when accelerating, up- ver is shifted to “S” position, the gear up or down to a gear that would shifting, downshifting or braking on will be shifted to 1st.
Page 121 03 07.07 3. Release the parking brake and brake 2. Shift the selector lever to the “S” posi- NOTICE pedal. Depress the accelerator pedal tion while holding down the brake pe- slowly for smooth starting. dal. Make sure that the gear position Do not hold the vehicle on an uphill indicator in the instrumental cluster dis- with the accelerator pedal applied.
Page 122 03 07.07 The system will re–try shifting automat- z If the gear cannot be engaged to ically. This will take some time, noise reverse when the selector lever is may be heard from the gears, and shift shifted from the “N” to “R” posi- shock may occur.
Page 123 03 07.07 If you stop for more than 90 seconds with Push downshift switch on the steering When you stop the vehicle, hold the the selector lever in the “S” position with- wheel.: Resume to 1st gear. brake pedal down or shift the selec- out holding down the brake pedal while “S”³“N”³“S”: Resume to 1st gear.
Page 124 03 07.07 NOTICE When leaving the vehicle, stop the engine and park the vehicle with z Do not hold or stop the vehicle on the gear engaged. In case you need a hill with the accelerator pedal ap- to leave the vehicle with the engine plied.
Page 125 03 07.07 Warning buzzer (long pulse sound) CAUTION It may sound when the selector lever is shifted to the “S” or “R” position In case the gear shift is not com- while racing the engine. pleted before the ignition switch is The clutch is heated with excessive turned off, the gear may not be en- SD16021...
Page 126 03 07.07 The selector lever is shifted from the In this case, turn the ignition “ON” before “N” position to the “S” or “R” position operate the shift lever. Shift the selector soon after starting the engine. lever to the “N” position once, then shift the selector lever again to the “S”...
Page 127 03 07.07 Manual transmission gear km/h (mph) 1 to 2 or 2 to 1 (15) 2 to 3 or 3 to 2 (25) 3 to 4 or 4 to 3 (40) 4 to 5 or 5 to 4 (45) Downshift to the appropriate gear if accel- SD16023 SB16017c eration is needed when you are cruising...
Page 128 03 07.07 Parking brake NOTICE CAUTION Do not downshift if you are going Before driving, be sure the parking faster than the maximum allowable brake is fully released and the park- speed for the next lower gear. ing brake reminder light is off. SB16008 Good driving practice If it is difficult to shift into reverse, put...
Page 129 03 07.07 Cruise control The cruise control allows you to cruise the vehicle at a desired speed over 40 km/h (25 mph) even with your foot off the accelerator pedal. Your cruising speed can be maintained up or down grades within the limits of engine SB16010 SB16011 performance,...
Page 130 If the vehicle speed drops 16 km/h (10 If this is the case, contact your Toyota mph) below the preset speed, the preset dealer and have your vehicle inspected. speed will also automatically cancel out.
Page 131 03 07.07 2003 MR2 from Aug. ’03 Prod. (OM17511U)
Page 132 03 07.07 SECTION – OPERATION OF INSTRUMENTS AND CONTROLS Car audio system Reference ..........Using your audio system .
Page 133 —Some basics Reference This section describes some of the basic TONE AND BALANCE features on Toyota audio systems. Some For details about your system’s tone and information may not pertain to your sys- balance controls, see the description of tem.
Page 134 03 07.07 YOUR RADIO ANTENNA YOUR COMPACT DISC PLAYER To lower the power antenna, turn off the When you insert a disc, gently push it in audio system by pushing “PWR·VOL”, or with the label side up. (The player will turn the ignition key to “LOCK”.
Page 135 03 07.07 —Controls and features Details of specific buttons, controls and features are described in the alphabetical list that follows. Z17047 2003 MR2 from Aug. ’03 Prod. (OM17511U)
Page 136 03 07.07 1 2 3 4 5 6 (Preset buttons) Compact Disc Player (Program) These buttons are used to preset and Push and hold “ ” (preset button 6) or Push “ ” to select the other side of a tune in radio stations.
Page 137 If the malfunction still exists, take your will appear on the display. This system When the audio system is set into com- vehicle to your Toyota dealer. allows you to set twelve FM stations, two pact disc operation, the display shows the for each of the preset button.
Page 138 03 07.07 With compact disc changer only— Compact disc player SCAN To play all the tracks in the magazine in There are two repeat features—You can Radio random order: either replay a disc track or a whole com- You can either scan all the frequencies on Push and hold “RAND”...
Page 139 03 07.07 Compact disc player SEEK/TRACK (Seeking/Track up/down) Compact disc player There are two scan features—you can ei- Radio Use this button to skip up or down to a ther scan the tracks on a specific disc or different track. In the seek mode, the radio finds and scan the first tracks of all the discs in the plays the next station up or down the...
Page 140 03 07.07 Car audio system operating hints TEXT Here are some common reception prob- NOTICE lems that probably do not indicate a prob- This button is used to change the display lem with your radio: To ensure correct audio system op- for the compact disc that contains text erations: data.
Page 141 03 07.07 Use high–quality cassettes. CARING FOR YOUR COMPACT DISC PLAYER AND DISCS Fading—AM broadcasts are reflected by Low–quality cassette tapes can cause the upper atmosphere—especially at night. many problems, including poor sound, The player is intended for use with 12 These reflected signals can interfere with inconsistent playing...
Page 142 03 07.07 Z17038 Z17037 G17032 Special shaped discs Labeled discs Use only compact discs marked as shown above. The following products may not be playable on your compact NOTICE disc player. To prevent damage to the player or Copy–protected CD changer, do not use special shaped, CD–R (CD–Recordable) low quality or labeled discs such as...
Page 143 03 07.07 Z17052 Z17053 Correct Wrong Handle compact discs carefully, espe- To clean a compact disc: Wipe it with a cially when you are inserting them. soft, lint–free cloth that has been damp- Hold them on the edge and do not ened with water.
Page 144 03 07.07 SECTION – OPERATION OF INSTRUMENTS AND CONTROLS Air conditioning system Controls ........... Air flow selector settings .
Page 145: Controls
03 07.07 Controls 1. Air intake selector 2. Air flow selector 3. “A/C” button 4. Fan speed selector 5. Temperature selector SB18008b 2003 MR2 from Aug. ’03 Prod. (OM17511U)
Page 146 03 07.07 Fan speed selector 4. Floor/Windshield—Air flows mainly from the floor vents and windshield Turn the knob to adjust the fan speed—to vents. the right to increase, to the left to de- crease. Use with the air intake selector posi- tioned in Fresh.
Page 147 If this happens, take your ve- hicle to a Toyota dealer for service. Air intake selector Move the lever to select the air source. 1. Recirculate—Recirculates the air inside the vehicle.
Page 148: Air Flow Selector Settings
03 07.07 Air flow selector settings Operating tips To cool off your Toyota after it has been parked in the hot sun, drive with the windows open for a few minutes. This vents the hot air, allowing the air conditioning to cool the interior more quickly.
Page 149 03 07.07 If following another vehicle on a dusty Heating Air conditioning road, or driving in windy and dusty For best results, set controls to: For best results, set controls to: conditions, it is recommended that the air intake selector be temporarily set to Fan speed—Any setting except “OFF”...
Page 150: Side Vents
03 07.07 Side vents Defogging Defrosting The inside of the windshield The outside of the windshield Open For best results, set controls to: For best results, set controls to: Fan speed—Any setting except “OFF” Fan speed—Any setting except “OFF” Temperature—Towards WARM Temperature—Towards WARM SB18005a (red zone) to heat;...
Page 151 03 07.07 2003 MR2 from Aug. ’03 Prod. (OM17511U)
Page 152 03 07.07 SECTION – OPERATION OF INSTRUMENTS AND CONTROLS Other equipment Clock ............Cigarette lighter and ashtray .
Page 153: Clock
1:01—1:29, the time will change to 1:00. Use a Toyota genuine cigarette lighter or If the time is between 1:30—1:59, the equivalent for replacement. time will change to 2:00. 2003 MR2 from Aug. ’03 Prod. (OM17511U)
Page 154: Glove Box
03 07.07 Glove box Front box ASHTRAY To use the ashtray, pull out the lid. When finished with your cigarette, thor- oughly extinguish it in the ashtray to pre- vent other cigarette butts from catching SB19026 SB41047 fire. After using the ashtray, close the lid completely.
Page 155: Auxiliary Box
03 07.07 Auxiliary box SB19031a SB19018 SB19019 Front of vehicle Instrument panel 2. Fix the cover by hitching the inside clip DRAINAGE OF THE FRONT BOX on the hood. In case that the water is pooled inside the To use the box, open it as shown in front box, remove the grommet on the NOTICE the illustration.
Page 156: Luggage Space
03 07.07 Luggage space NOTICE Folding board During hot weather, the interior of the vehicle becomes very hot. Do not leave anything flammable or deform- able such as a lighter, glasses, etc. SB19027a SB12059a inside. Flare Lean the seatback forward to use the CAUTION luggage space.
Page 157 03 07.07 NOTICE z Do not place valuables in the lug- gage space to prevent robbery. z Do not lower the soft top while placing a luggage which is higher SB19030 SB19029 than the bottom edge of the flare inside the luggage space. The luggage may be damaged by hitting the folding board or the im- properly folded soft top may flap in...
Page 158: Cup Holders
03 07.07 Cup holders The cup holders are designed for hold- NOTICE ing cups or drink–cans securely in its holes. z Do not place tapered things or a long luggage into luggage Front: To use the cup holders, pull them space.
Page 159: Floor Mat
03 07.07 Floor mat SB19023a SB19022 Use a floor mat of the correct size. CAUTION If the floor carpet and floor mat have two holes, then it is designed for use with two Make sure the floor mat is properly locking clips.
Page 160 INFORMATION BEFORE DRIVING YOUR TOYOTA Information before driving your Toyota Break–in period ..........
Page 161: Break-In Period
To help prevent gas station mix–ups, your to the future economy and long life of steady speed on level roads, consult your Toyota has a smaller fuel tank opening. your vehicle: Toyota dealer. The special nozzle on pumps with un-...
Page 162 If you use gasohol in your problems. is expected to be applied world wide. Toyota, be sure that it has an octane The WWFC consists of three categories rating no lower than 87. z If driveability problems occur (poor that depend on required emission lev-...
Page 163: Fuel Pump Shut Off System
03 07.07 Fuel pump shut off system Operation in foreign countries Three–way catalytic converter If you plan to drive your Toyota in The fuel pump shut off system stops sup- plying fuel to the engine to minimize the another country...
Page 164: Engine Exhaust Cautions
A large amount of unburned gases vehicle in for a check–up as soon Avoid inhaling the engine exhaust. flowing into the three–way catalytic as possible. Remember, your Toyota It contains carbon monoxide, which converter may cause it to overheat dealer knows your vehicle and its is a colorless and odorless gas.
Page 165: Facts About Engine Oil Consumption
03 07.07 Facts about engine oil consumption FUNCTIONS OF ENGINE OIL The amount of engine oil consumed de- To allow proper operation of your pends on the viscosity of the oil, the Engine oil has the primary functions of vehicle’s ventilation system, keep quality of the oil and the conditions the lubricating and cooling the inside of the the inlet grilles in front of the wind-...
Page 166: Iridium-Tipped Spark Plugs
Therefore, it SB21011 brake system warning light may come on. is essential that the oil level be checked regularly. Toyota recommends that the oil level be checked every time you refuel CAUTION the vehicle. Do not drive your vehicle with only a...
Page 167 03 07.07 When the anti–lock brake system is ac- Effective way to press the ABS brake CAUTION tivated, the following conditions may pedal: occur. They do not indicate a malfunc- When anti–lock brake system Do not pump the brake pedal if the tion of the system: function is in action, you may feel the engine stalls.
Page 168 03 07.07 If tire grip performance exceeds its Install all 4 tires of specified size at capability, or if hydroplaning occurs appropriate pressure: The anti–lock during high speed driving in the rain, brake system detects vehicle speeds the anti–lock brake system does not using the speed sensors for respec- provide vehicle control.
Page 169: Brake Pad Wear Limit Indicators
CAUTION tored warning light system. Contact your Toyota dealer as soon as Do not start or run the engine while possible to service the vehicle. your vehicle is supported by a jack. The light does not come on when the The vehicle could be driven off the ignition key is turned to the “ON”...
Page 170: Your Toyota's Identification
This number is on the left top of the instrument panel, and can be seen through the windshield from outside. This is the primary identification number for your Toyota. It is used in registering the ownership of your vehicle. 2003 MR2 from Aug. ’03 Prod. (OM17511U)
Page 171: Theft Prevention Labels
03 07.07 Theft prevention labels Suspension and chassis Your new vehicle carries theft preven- CAUTION tion labels which are approximately 56 mm (2.20 in.) by 16 mm (0.63 in.). Do not modify the suspension/chassis The purpose of these labels is to reduce with lift kits, spacers, springs, etc.
Page 172: Tire Information
03 07.07 Tire information— —Tire symbols This illustration indicates typical tire symbols. 1. Tire size—For details, see “Tire size” on page 143. 2. DOT and Tire Identification Number (TIN)—For details, see “DOT and Tire Identification Num- ber (TIN)” on page 142. 3.
Page 173 03 07.07 —DOT and Tire Identification Number (TIN) 7. Uniform tire quality grading— The “DOT” symbol certifies that the For details, see “Uniform tire quali- tire conforms to applicable Federal ty grading” that follows. Motor Vehicle Safety Standards. 8. Tire ply composition and mate- rials—Plies mean a layer of rub- SB21022a ber–coated parallel cords.
Page 174 03 07.07 —Tire size —Name of each section of tire SB21021 SU21026a SU21027 This illustration indicates typical tire 1. Section width 1. Bead size. 2. Tire height 2. Sidewall 1. Section width (in millimeters) 3. Wheel diameter 3. Shoulder 2. Aspect ratio (tire height to section 4.
Page 175 150 would wear the purchasers and/or prospective Temperature A, B, C—The tempera- purchasers of Toyota vehicles with in- one and a half (1–1/2) times as well ture grades are A (the highest), B, formation on uniform tire quality grad- on the government course as a tire and C, representing the tire’s resist-...
Page 176 03 07.07 Warning: The temperature grades for this tire are established for a tire that is properly inflated and not over- loaded. Excessive speed, underinfla- tion, or excessive loading, either sep- arately or in combination, can cause heat buildup and possible tire failure. 2003 MR2 from Aug.
Page 177 03 07.07 —Tire related terms Tire inflation pressure when the vehicle has been parked at least 3 hours or Cold tire inflation pressure more, or it has not been driven more than 1.5 km or 1 mile under that condition The maximum cold inflation pressure to which a tire may be inflated and shown Maximum inflation pressure on the sidewall of the tire...
Page 178 03 07.07 Vehicle capacity weight The rated cargo and luggage load plus 68 kg (150 lb.) times the vehicle’s (Total load capacity) designated seating capacity (A) The sidewall that contains a whitewall, bears white lettering or bears manufacturer, brand, and/or model name molding that is higher or deeper than the same molding on the other sidewall of the tire or than the same molding on the other sidewall of the tire, or Intended outboard sidewall...
Page 179 03 07.07 Table 1–Occupant loading and distribution for vehicle normal load for various designated seating capacities Designated seating capacity, number Vehicle normal load, number of occu- Occupant distribution in a normally of occupants pants loaded vehicle 2 through 4 2 in front 5 through 10 2 in front, 1 in second seat 2003 MR2 from Aug.
Page 180: Vehicle Load Limits
When stowing luggage or cargo in the capacity, seating capacity, towing ca- vehicle, observe the following: Toyota does not recommend towing pacity and cargo capacity. Follow the a trailer with your vehicle. Your ve- D Put luggage or cargo in the front load limits shown below.
Page 181 Toyota does not recommend towing a trailer with your vehicle. Your ve- hicle is not designed for trailer towing. 2003 MR2 from Aug. ’03 Prod. (OM17511U)
Page 182 03 07.07 113 kg – 70 kg = 43 kg. CAUTION (249 lb. – 154 lb. = 95 lb.) As shown in the above example, if the Even if the total load of occu- number of occupants increases, the pant’s weight and the cargo load cargo and luggage load equaling the is less than the total load capac- SB21023...
Page 183: Types Of Tires
03 07.07 Types of tires Determine what kind of tires your CAUTION vehicle is originally equipped with. 1. Summer tires D Do not mix summer and all sea- Summer tires are high–speed capabil- son tires on your vehicle as ity tires best suited to highway driving this can cause dangerous han- under dry conditions.
Page 184 03 07.07 SECTION STARTING AND DRIVING Starting and driving Before starting the engine ........How to start the engine .
Page 185: Before Starting The Engine
03 07.07 How to start the engine— (a) Before cranking Before starting the engine (b) Starting the engine 1. Check the area around the vehicle be- Before starting the engine, be sure to 1. Apply the parking brake firmly. fore entering it. follow instructions “(a)
Page 186: Tips For Driving In Various Conditions
If they still do not work safely, pull to the side of the road and call a Toyota dealer for assistance. 2003 MR2 from Aug. ’03 Prod. (OM17511U)
Page 187: Winter Driving Tips
Even if the legal speed limit See page 206 in Section 7–2 for recom- Only use “Toyota Super Long Life Coolant” permits it, do not drive over 140 mended viscosity. Leaving a heavy sum-...
Page 188: Dinghy Towing
03 07.07 Dinghy towing Do not use your parking brake when NOTICE there is a possibility it could freeze. Dinghy towing does not eliminate the When parking, put the transmission into possibility of damage to your vehicle. “S(1)” or “R” (sequential manual transmis- sion) or into first or reverse (manual transmission) and block the front wheels.
Page 189: Trailer Towing
Excess weight puts a heavier load on the engine, causing greater fuel consumption. Avoid lengthy warm–up idling. Once Toyota does not recommend towing a trail- NOTICE the engine is running smoothly, begin er with your MR2. It is not designed for driving—but gently.
Page 190 03 07.07 Avoid continuous speeding up and Keep the bottom of your vehicle free slowing down. Stop–and–go driving from mud, etc. This not only lessens wastes fuel. weight but also helps prevent corro- sion. Avoid unnecessary stopping braking. Maintain a steady pace. Try Keep your vehicle tuned–up and in to time the traffic signals so you only top shape.
Page 191 03 07.07 2003 MR2 from Aug. ’03 Prod. (OM17511U)
Page 192 03 07.07 SECTION IN CASE OF AN EMERGENCY In case of an emergency If your vehicle will not start ........If your engine stalls while driving .
Page 193: If Your Vehicle Will Not Start
Have the key checked at your al and brake pedal in these positions for cause a collision when the engine Toyota dealer. If none of your keys work, 15 seconds and release them. Then re- starts. Also the three- way catalytic...
Page 194 03 07.07 (c) Jump starting To avoid serious personal injury and NOTICE The gas normally produced by a damage to your vehicle which might re- battery will explode if a flame or sult from battery explosion, acid burns, Do not crank for more than 30 sec- spark is brought near.
Page 195 03 07.07 JUMP STARTING PROCEDURE Discharged battery 1. If the booster battery is installed in another vehicle, make sure the vehicles are not touching. Turn off all unneces- Booster Jumper cable sary lights and accessories. battery SB41055 SB41056 2. If required, remove all the vent plugs from the booster and discharged batter- ies.
Page 196: If Your Engine Stalls While Driving
(for example, lights left on), the battery or accidentally let the you should have it checked at your Toyota jumper cables or clamps touch any- dealer. thing except the correct battery termi- nals or the ground.
Page 197: If You Cannot Increase The Engine Speed
When the engine is running, keep your vehicle checked by your Toyota deal- flashers. Put the transmission in “N” hands and clothing away from the er as soon as possible. (sequential manual transmission) or in moving fan and engine drive belts.
Page 198: If You Have A Flat Tire
You should have it checked as bility of personal injury: a highway. Park on a level spot soon as possible at your Toyota dealer. with firm ground. D Follow jacking instructions. 2. Stop the engine and turn on your D Do not put any part of your emergency flashers.
Page 199 03 07.07 —Spare tire with turning direction indicators NOTICE D Make sure to set the jack prop- erly in the jack point. Raising Do not continue driving with a the vehicle with jack improper- deflated tire. Driving even a ly positioned will damage the short distance can damage a vehicle or may allow the ve- tire and wheel beyond repair.
Page 200 You will find a jack in the tool bag. To prepare yourself for an emergency, D The spare tire was designed you should familiarize yourself with especially for your Toyota. Do the use of the jack, each of the tools not use it on any other vehicle. SB41053a and their storage locations.
Page 201 03 07.07 SB41047 SB41061a SB41063b To remove the spare tire: 2. Remove the spare wheel cover. 3. Loosen the bolt and remove it. 1. Open the front box cover in the Then take the spare tire out of the trunk. vehicle.
Page 202 03 07.07 —Blocking the wheel —Loosening wheel nuts CAUTION Never use oil or grease on the bolts or nuts. The nuts may loos- en and the wheels may fall off, SB41035 SB41027a which could cause a serious ac- cident. 2. Block the wheel diagonally op- 3.
Page 203 03 07.07 —Positioning the jack —Raising your vehicle CAUTION Never get under the vehicle when the vehicle is supported by the jack alone. SB41036 SB41029 4. Position the jack at the correct 5. After making sure that no one jack point as shown. is in the vehicle, raise it high enough so that the compact Make sure the jack is positioned on...
Page 204 03 07.07 —Changing wheels —Reinstalling wheel nuts SB41028a SB41044b SD04004b Before putting wheels on, remove any 6. Remove the wheel nuts and 7. Reinstall all the wheel nuts with change tires. corrosion on the mounting surfaces finger tight. with a wire brush or such. Installation Lift the flat tire straight off and put it Reinstall the wheel nuts (tapered end of wheels without good metal- to- met-...
Page 205 03 07.07 —Lowering your vehicle CAUTION CAUTION Never use oil or grease on the D When lowering the vehicle, bolts or nuts. Doing so may lead make sure all portions of your to overtightening the nuts and body and all other persons SB41031b damaging the bolts.
Page 206 03 07.07 —After changing wheels 9. Check the air pressure of the re- CAUTION placed tire. Adjust the air pressure to the specifi- Before driving, make sure all the cation designated on page 288 in tools, jack and flat tire are se- Section 8.
Page 207: If Your Vehicle Becomes Stuck
03 07.07 If your vehicle becomes stuck If your vehicle becomes stuck in snow, NOTICE mud, sand, etc., then you may attempt to rock the vehicle free by moving it If you rock your vehicle, observe the forward and backward. following precautions to prevent dam- age to the transmission and other CAUTION...
Page 208: If Your Vehicle Needs To Be Towed
If towing is necessary, we recommend (a) Towing with wheel lift type truck (a) Towing with wheel lift type truck— you to have it done by your Toyota From front—We recommend using a tow- dealer or a commercial tow truck ser- ing dolly under the rear wheels.
Page 209 03 07.07 —Emergency towing CAUTION (c) Towing with sling type truck Do not tow without a towing dolly when the ignition switch is in the “ON” position and/or when the trans- SB41057 SB41033c mission is not in the neutral gear position.
Page 210 If towing is necessary, we recommend Before towing, release the parking brake CAUTION you to have it done by your Toyota and put the transmission in “N” (sequential dealer or a commercial tow truck ser- manual transmission) or in neutral (manual Use extreme caution when towing a vice.
Page 211 03 07.07 —Installing towing eyelet CAUTION If the engine is not running, the power assist for the brakes and steering will not work so steering SB41065 SB41066 and braking will be much harder than usual. Do not tow with a cable or chain when the ignition switch is in the “ON”...
Page 212: If You Cannot Shift The Sequential Manual Transmission Selector Lever
2. Pry up the cover with a flat- bladed sult in death or serious injury. Be sure to have the system checked by screwdriver or equivalent. your Toyota dealer as soon as possible. 2003 MR2 from Aug. ’03 Prod. (OM17511U)
Page 213: If You Lose Your Keys
Toyota dealer if you can give them the key number and master key. Even if you lose only one key, contact your Toyota dealer to make a new key. If you lose all your master keys, you cannot make new keys; the whole engine immobi- lizer system must be replaced.
Page 214 03 07.07 SECTION IN CASE OF AN EMERGENCY In case of an emergency If your vehicle will not start ........If your engine stalls while driving .
Page 215: If Your Vehicle Will Not Start
Have the key checked at your al and brake pedal in these positions for cause a collision when the engine Toyota dealer. If none of your keys work, 15 seconds and release them. Then re- starts. Also the three–way catalytic...
Page 216 03 07.07 (c) Jump starting To avoid serious personal injury and NOTICE The gas normally produced by a damage to your vehicle which might re- battery will explode if a flame or sult from battery explosion, acid burns, Do not crank for more than 30 sec- spark is brought near.
Page 217 03 07.07 JUMP STARTING PROCEDURE Discharged battery 1. If the booster battery is installed in another vehicle, make sure the vehicles are not touching. Turn off all unneces- Booster Jumper cable sary lights and accessories. battery SB41055 SB41056 2. If required, remove all the vent plugs from the booster and discharged batter- ies.
Page 218: If Your Engine Stalls While Driving
(for example, lights left on), the battery or accidentally let the you should have it checked at your Toyota jumper cables or clamps touch any- dealer. thing except the correct battery termi- nals or the ground.
Page 219: If You Cannot Increase The Engine Speed
When the engine is running, keep your vehicle checked by your Toyota deal- flashers. Put the transmission in “N” hands and clothing away from the er as soon as possible. (sequential manual transmission) or in moving fan and engine drive belts.
Page 220: If You Have A Flat Tire
You should have it checked as bility of personal injury: a highway. Park on a level spot soon as possible at your Toyota dealer. with firm ground. D Follow jacking instructions. 2. Stop the engine and turn on your D Do not put any part of your emergency flashers.
Page 221 03 07.07 —Spare tire with turning direction indicators NOTICE D Make sure to set the jack prop- erly in the jack point. Raising Do not continue driving with a the vehicle with jack improper- deflated tire. Driving even a ly positioned will damage the short distance can damage a vehicle or may allow the ve- tire and wheel beyond repair.
Page 222 You will find a jack in the tool bag. To prepare yourself for an emergency, D The spare tire was designed you should familiarize yourself with especially for your Toyota. Do the use of the jack, each of the tools not use it on any other vehicle. SB41053a and their storage locations.
Page 223 03 07.07 SB41047 SB41061a SB41063b To remove the spare tire: 2. Remove the spare wheel cover. 3. Loosen the bolt and remove it. 1. Open the front box cover in the Then take the spare tire out of the trunk. vehicle.
Page 224 03 07.07 —Blocking the wheel —Loosening wheel nuts CAUTION Never use oil or grease on the bolts or nuts. The nuts may loos- en and the wheels may fall off, SB41035 SB41027a which could cause a serious ac- cident. 2. Block the wheel diagonally op- 3.
Page 225 03 07.07 —Positioning the jack —Raising your vehicle CAUTION Never get under the vehicle when the vehicle is supported by the jack alone. SB41036 SB41029 4. Position the jack at the correct 5. After making sure that no one jack point as shown. is in the vehicle, raise it high enough so that the compact Make sure the jack is positioned on...
Page 226 03 07.07 —Changing wheels —Reinstalling wheel nuts SB41028a SB41044b SD04004b Before putting wheels on, remove any 6. Remove the wheel nuts and 7. Reinstall all the wheel nuts with change tires. corrosion on the mounting surfaces finger tight. with a wire brush or such. Installation Lift the flat tire straight off and put it Reinstall the wheel nuts (tapered end of wheels without good metal–to–met-...
Page 227 03 07.07 —Lowering your vehicle CAUTION CAUTION Never use oil or grease on the D When lowering the vehicle, bolts or nuts. Doing so may lead make sure all portions of your to overtightening the nuts and body and all other persons SB41031b damaging the bolts.
Page 228 03 07.07 —After changing wheels 9. Check the air pressure of the re- CAUTION placed tire. Adjust the air pressure to the specifi- Before driving, make sure all the cation designated on page 242 in tools, jack and flat tire are se- Section 8.
Page 229: If Your Vehicle Becomes Stuck
03 07.07 If your vehicle becomes stuck If your vehicle becomes stuck in snow, NOTICE mud, sand, etc., then you may attempt to rock the vehicle free by moving it If you rock your vehicle, observe the forward and backward. following precautions to prevent dam- age to the transmission and other CAUTION...
Page 230: If Your Vehicle Needs To Be Towed
If towing is necessary, we recommend (a) Towing with wheel lift type truck you to have it done by your Toyota (a) Towing with wheel lift type truck— From front—We recommend using a tow- dealer or a commercial tow truck ser- ing dolly under the rear wheels.
Page 231 03 07.07 —Emergency towing CAUTION (c) Towing with sling type truck Do not tow without a towing dolly when the ignition switch is in the “ON” position and/or when the trans- SB41057 SB41033c mission is not in the neutral gear position.
Page 232 If towing is necessary, we recommend Before towing, release the parking brake CAUTION you to have it done by your Toyota and put the transmission in “N” (sequential dealer or a commercial tow truck ser- manual transmission) or in neutral (manual Use extreme caution when towing a vice.
Page 233 03 07.07 —Installing towing eyelet CAUTION If the engine is not running, the power assist for the brakes and steering will not work so steering SB41065 SB41066 and braking will be much harder than usual. Do not tow with a cable or chain when the ignition switch is in the “ON”...
Page 234: If You Cannot Shift The Sequential Manual Transmission Selector Lever
2. Pry up the cover with a flat–bladed sult in death or serious injury. Be sure to have the system checked by screwdriver or equivalent. your Toyota dealer as soon as possible. 2003 MR2 from Aug. ’03 Prod. (OM17511U)
Page 235: If You Lose Your Keys
Toyota dealer if you can give them the key number and master key. Even if you lose only one key, contact your Toyota dealer to make a new key. If you lose all your master keys, you cannot make new keys; the whole engine immobi- lizer system must be replaced.
Page 236: Corrosion Prevention And Appearance Care
APPEARANCE CARE Corrosion prevention and appearance care Protecting your Toyota from corrosion ......Washing and waxing your Toyota .
Page 237 Now, it is up to be dry. more harm than good to simply wet the you. Proper care of your Toyota can help High ambient temperatures can cause mud and debris without removing. The ensure long–term corrosion prevention.
Page 238 Washing and waxing your Toyota For washing instructions for soft top, see Check the interior of your vehicle. Wa- Washing your Toyota ter and dirt can accumulate under the “Soft top” on page 187. Keep your vehicle clean by regular floor mats and could cause corrosion.
Page 239 NOTICE or neutral detergent. cause water to enter the vehicle. Do not run your Toyota through auto- Plastic bumpers: Wash carefully. Do not matic car washes or possible damage scrub with abrasive cleaners. The bumper to the soft top may result.
Page 240 03 07.07 Waxing your Toyota Touch–up paint NOTICE Polishing and waxing is recommended Touch–up paint may be used to cover z Do not use harsh or abrasive clean- to maintain the original beauty of your small chips or scratches. ers as they may damage the top Toyota’s finish.
Page 241 03 07.07 Cleaning the interior 2. Scrub with a small, soft bristle hand- NOTICE CAUTION brush. Add water as needed until the cleaner becomes soapy. Allow solution Do not use solvent, thinner, gasoline Do not wash the vehicle floor with to settle for two to five minutes.
Page 242 03 07.07 Leather Interior NOTICE NOTICE The leather upholstery may be cleaned z Do not use dye or bleach on the z Do not use organic substances (sol- with neutral detergent for wool. belts—it may weaken them. vents, kerosene, alcohol, gasoline, Remove dirt using a soft cloth dampened etc.) or alkaline or acidic solutions.
Page 243 Improper cleaning of the leather up- holstery could result in discolor- ation or staining. If you have any questions about the cleaning of your Toyota, your local Toyota dealer will be pleased to answer them. 2003 MR2 from Aug. ’03 Prod. (OM17511U)
Page 244 03 07.07 SECTION VEHICLE MAINTENANCE AND CARE Vehicle maintenance and care Maintenance requirements ........General maintenance .
Page 245 See form them are presented in Section 7. or if you prefer, your Toyota dealer will be “Owner’s Warranty Information Booklet” pleased to do them at a nominal cost.
Page 246 Supplement” for the details. vehicle to your Toyota dealer or a quali- Radiator, condenser and hoses fied service shop immediately. It is recom- Check that the front of the radiator and...
Page 247 03 07.07 Power steering fluid level Seats OUTSIDE THE VEHICLE Check the level through the reservoir. The Check that all seat controls such as seat Items listed below should be performed level should be in the “HOT” or “COLD” adjusters, seatback recliner, etc. operate from time to time, unless otherwise range depending on the fluid temperature.
Page 248 Be on the alert for changes in perfor- If you notice any of these clues, take your Some states have vehicle emission in- mance, sounds, and visual tip–offs that vehicle to your Toyota dealer as soon as spection programs which include OBD indicate service is needed.
Page 249 40 trips or more are taken. If your vehicle does not pass the I/M test even the malfunction indicator lamp does not come on, contact your Toyota dealer to prepare the vehicle for re–testing. 2003 MR2 from Aug. ’03 Prod. (OM17511U)
Page 250 03 07.07 SECTION – DO–IT–YOURSELF MAINTENANCE Introduction Engine compartment overview ....... Trunk room overview .
Page 251 03 07.07 Engine compartment overview 1. Fuse block 2. Battery 3. Engine oil filler cap 4. Engine oil level dipstick 5. Engine coolant reservoir SC71012b 2003 MR2 from Aug. ’03 Prod. (OM17511U)
Page 252 03 07.07 Trunk room overview 1. Brake fluid reservoir 2. Fuse block 3. Power steering fluid reservoir 4. Radiator 5. Electric cooling fans 6. Condenser 7. Windshield washer fluid tank SB71020b 2003 MR2 from Aug. ’03 Prod. (OM17511U)
Page 253 03 07.07 Fuse locations SB71011a SB71013a SB71010a SB71017a SB71019a 2003 MR2 from Aug. ’03 Prod. (OM17511U)
Page 254 Toyota Warranty statement for details and engine, radiator, exhaust manifold, where you may be exposed to flying suggestions. power steering fluid reservoir and or falling material, fluid spray, etc. This section gives instructions only for spark plug boots, etc.—will be hot.
Page 255 03 07.07 z Add only “Toyota Super Long Life z When closing the engine hood or Do not leave used oil within the Coolant” or similar high quality eth- trunk, check to see that you have reach of children. ylene...
Page 256 CHECKING BRAKE FLUID ADDING WASHER FLUID need to perform do–it–yourself mainte- Parts (if level is low): Parts: nance. Remember all Toyota parts are de- SAE J1703 or FMVSS No.116 DOT 3 Water signed in metric sizes, so your tools must brake fluid be metric.
Page 257 03 07.07 Positioning the jack CAUTION Do not raise the vehicle with some- one in the vehicle. When jacking, be sure to observe the When raising the vehicle, do not following to reduce the possibility of place any objects on top of or un- personal injury: derneath the jack.
Page 258 03 07.07 SECTION – DO–IT–YOURSELF MAINTENANCE Engine and Chassis Checking the engine oil level ....... . . Checking the engine coolant level .
Page 259: Checking The Engine Oil Level
O.K. Too full If the oil level is below or only slightly “Toyota Genuine Motor Oil” is filled in above the low level, add engine oil of your Toyota vehicle. Use Toyota approved the same type as already in the engine.
Page 260 03 07.07 Recommended viscosity: Oil identification marks SAE 5W–30 Either or both API registered marks are added to some oil containers to help you select the oil you should use. The API Service Symbol is located any- where on the outside of the container. SOIL13 The top portion of the label shows the oil quality...
Page 261: Checking The Engine Coolant Level
Toyota engines. Do not use plain water alone. If you can find no leak, have your Toyota Please contact your Toyota dealer for dealer test the cap pressure and check further details about “Toyota...
Page 262: Checking The Radiator And Condenser
Checking the radiator and condenser Checking brake fluid If any of the above parts are extremely dirty or you are not sure of their condi- tion, take your vehicle to a Toyota dealer. CAUTION Z72109 SB72015 To prevent burning yourself, be care- ful not to touch the radiator or con- denser when the engine is hot.
Page 263: Checking Power Steering Fluid
This brings the fluid to the correct SB72002 Toyota P.S fluid EH or equivalent to bring level when you put the cap back on. the level within the range. Use only newly opened brake fluid. Once...
Page 264: Checking Tire Inflation Pressure
03 07.07 Checking tire inflation pressure Keep your tire inflation pressures at the proper level. The recommended cold tire inflation pressures, tire sizes and the com- bined weight of occupants and cargo (vehicle capacity weight) are de- scribed on page 238 and 242. They are also described on the tire and loading information label.
Page 265 In case of applying If a tire frequently needs refilling, too much air, press the center of have it checked by your Toyota deal- the valve and release the air to ad- just. 2003 MR2 from Aug. ’03 Prod. (OM17511U)
Page 266: Checking And Replacing Tires
03 07.07 Checking and replacing tires CAUTION High tire pressure (overinfla- Tread wear indicator tion)— Keep your tires properly inflated. D Poor handling Otherwise, the following condi- D Excessive wear tions may occur and cause an ac- D Uneven wear cident resulting in death or seri- ous injuries.
Page 267 03 07.07 The tires on your Toyota have built–in The effectiveness of snow tires is NOTICE tread wear indicators to help you lost if the tread wears down below know when the tires need replace- 4 mm (0.16 in.). Low profile tire like 185/55R15 ment.
Page 268 03 07.07 This also applies to the spare tire and Check that the maximum load of the CAUTION tires stored for future use. replaced tire is greater than 1/2 of the Gross Axle Weight Ratings (GAWR) REPLACING YOUR TIRES Observe the following instruc- of either the front axle or the rear When replacing a tire, use a tire of tions.
Page 269: Rotating Tires
03 07.07 Rotating tires Toyota recommends all four tires, Do not rotate the tires as the tire or at least both front or rear tires sizes are different such as with be replaced as a set. front to rear, left to right or using the spare tire.
Page 270: Installing Snow Tires And Chains
Installing snow tires on the rear wheels For 215/45R16 tires, use genuine Toyota On wet or dry roads, conventional tires only can lead to an excessive difference tire chains or equivalent for use on the provide better traction than snow tires.
Page 271: Replacing Wheels
Do not exceed 50 km/h (30 mph) or Correct replacement wheels are available chain manufacturer’s recom- at your Toyota dealer. mended speed limit, whichever is A wheel of a different size or type may lower. adversely affect handling, wheel and bear-...
Page 272: Aluminum Wheel Precautions
When using tire chains, be careful not characteristics resulting in loss of to damage the aluminum wheels. control. Use only the Toyota wheel nuts and wrench designed for your aluminum wheels. When balancing your wheels, use only Toyota balance weights or equivalent and a plastic or rubber hammer.
Page 273 03 07.07 2003 MR2 from Aug. ’03 Prod. (OM17511U)
Page 274 03 07.07 SECTION – DO–IT–YOURSELF MAINTENANCE Electrical components Checking battery condition ........Battery recharging precautions .
Page 275: Checking Battery Condition
03 07.07 Checking battery condition— —Precautions —Checking battery exterior CAUTION If electrolyte gets on your skin, Hold–down clamp thoroughly wash the contact area. If BATTERY PRECAUTIONS you feel pain or burning, get medi- cal attention immediately. The battery produces flammable and explosive hydrogen gas.
Page 276: Battery Recharging Precautions
Good dangerous. The battery may explode Charging causing personal injuries. necessary. Have Dark White battery checked by your Toyota NOTICE dealer. Never recharge the battery while the Clear or Have battery engine is running. Also, be sure all light checked by your accessories are turned off.
Page 277: Checking And Replacing Fuses
03 07.07 Checking and replacing fuses SB73035 SB73037 SB73066 Good Blown Good Blown Type A Type C the headlights or other electrical components do not work, check the fuses. If any of the fuses are blown, they must be replaced. See “Fuse locations”...
Page 278: Adding Washer Fluid
If the new fuse immediately blows out, manufacturer’s directions for how much to there is a problem with the electrical sys- mix with water. tem. Have your Toyota dealer correct it as soon as possible. 2003 MR2 from Aug. ’03 Prod. (OM17511U)
Page 279: Replacing Light Bulbs
To prevent burning yourself, do not of the lens, or if there is water pooled replace the light bulbs while they inside the light, contact your Toyota deal- are hot. Halogen bulbs have pressurized gas inside and require special handling.
Page 280 03 07.07 A: HB4 halogen bulbs Bulb Light bulbs Type B: HB3 halogen bulbs C: H7 halogen bulbs Headlights D: Wedge base bulbs (amber) — (Low beam) E: Wedge base bulbs (clear) F: Double end bulbs Headlights — (Hi beam) BEFORE REPLACING LIGHT BULBS —...
Page 281 03 07.07 —Headlights (low beam) SC73006b SC18005 SB73043a Removing clips 2. Remove the cover in the trunk. 1. Unplug the connector. Remove the rubber cover. Remove and install the cover clips as shown in the following illustrations. If the connector is tight, wiggle it. SC18006 Installing clips 2003 MR2 from Aug.
Page 282 Aiming is not necessary after replacing the bulb. When aiming adjustment is nec- essary, contact your Toyota dealer. 2003 MR2 from Aug. ’03 Prod. (OM17511U)
Page 283 03 07.07 —Front fog lights If either the left or right front fog lights burns out, contact your Toyota dealer. NOTICE Do not try to replace the front fog light bulbs by yourself. You may dam- SB73078 SB73079 age the vehicle.
Page 284 03 07.07 —Parking lights —Front turn signal lights —Front side marker lights SD73005a SD73007a SB73071a Phillips–head screw: Use a phillips–head screwdriver. SD73006a SD73008a 2003 MR2 from Aug. ’03 Prod. (OM17511U)
Page 285 03 07.07 —Rear turn signal, stop/tail, stop and back–up lights SB73072a SB73074a SD73009 SB73073a 2003 MR2 from Aug. ’03 Prod. (OM17511U)
Page 286 03 07.07 —License plate lights SD73010a SB73021 SB73023 a: Back–up light b: Rear turn signal light c: Stop/tail light d: Stop light CAUTION Be careful when you work in the area SB73022 around the engine after driving in or- der to prevent burning yourself. The engine hood, the support rod, or sur- rounding area could be hot after driv- ing.
Page 287 03 07.07 —High mounted stop light SB73062 SB73060 SB73058 SB73052 SB73057 SB73059 2003 MR2 from Aug. ’03 Prod. (OM17511U)
Page 288 03 07.07 CAUTION Be careful when you work in the area around the engine after driving in or- der to prevent burning yourself. The engine hood, the support rod, or sur- rounding area could be hot after driv- ing. 2003 MR2 from Aug. ’03 Prod. (OM17511U)
Page 289 03 07.07 2003 MR2 from Aug. ’03 Prod. (OM17511U)
Page 290 03 07.07 SECTION SPECIFICATIONS Specifications Dimensions and weight ........Engine .
Page 291: Dimensions And Weight
03 07.07 Dimensions and weight Engine Fuel Model: Fuel type: Overall length mm (in.) 3885 (153.0) 1ZZ–FE Overall width mm (in.) 1695 (66.7) Unleaded gasoline, Octane Rating 87 Type: (Research Octane Number 91) or higher ∗ Overall height mm (in.) 1240 (48.8) 4 cylinder in line, 4 cycle, gasoline...
Page 292: Engine
3.5 (3.7, 3.1) Spark plug type: SAE 5W–30 DENSO SK16R11 “Toyota Genuine Motor Oil” is filled in your Toyota vehicle. Use Toyota approved IFR5A11 “Toyota Genuine Motor Oil” or equivalent Spark plug gap, mm (in.): to satisfy the following grade and viscos- 1.1 (0.043)
Page 293 “Toyota Super Long Life Coolant” is Genuine Sequential Fluid MANUAL TRANSAXLE filled in your Toyota vehicle at factory cause deterioration in shift performance Oil capacity, L (qt., Imp. qt.): fill. In order to avoid technical problems, and durability, and ultimately damage Vehicle with limited–slip differential...
Page 294 490 N (50 kgf, 110 lbf) Less than 30 mm (1.2 in.) with the engine running, mm (in.): Power steering fluid type: 85 (3.4) Toyota P.S fluid EH or equivalent Pedal free play, mm (in.): 1—6 (0.04—0.24) Pad wear limit, mm (in.): 1.0 (0.04)
Page 295: Tires
03 07.07 Tires Tire size and cold tire inflation pressure: Except spare tire Tire inflation pressure Tire inflation ressure Tire size Tire size Wheel size Wheel size kPa (kgf/cm or bar, psi) Front 185/55R15 81V 180 (1.8, 26) Rear 215/45R16 86W 220 (2.2, 32) Spare tire Tire size...
Page 296: Fuses
03 07.07 Fuses SB73067 SB73025a SB73026b Trunk room Trunk room Instrument panel Fuses (type A) 10. HTR 10 A: Air conditioning system 17. DEF 25 A: Rear window defogger sys- 1. 30 A: Spare fuse 11. WIPER 20 A: Windshield wiper and washer 18.
Page 297 03 07.07 33. CIG 15 A: Cigarette lighter 46. HEAD LH LWR 10A: Left–hand head- light (low beam) 34. I/UP 7.5 A: Engine idle up system 47. EFI2 7.5 A: Multiport fuel injection sys- 35. ALT–S 7.5 A: Charging system tem/sequential multiport fuel injection 36.
Page 298 03 07.07 SECTION REPORTING SAFETY DEFECTS FOR U.S. OWNERS Reporting safety defects for U.S. owners Reporting safety defects for U.S. owners ..... . 2003 MR2 from Aug.
Page 299 However, NHTSA cannot become involved in individual problems between you, your dealer, or Toyota Motor Sales, U.S.A., Inc. 2003 MR2 from Aug. ’03 Prod. (OM17511U)
Page 300 The Toyota authorized Repair Manual is packed with literally everything you need to know to perform your own maintenance in virtually every area of your new vehicle.
Page 301 The repair manual outlines exactly what main The repair manual for MR2, written in English, tenance is required and clearly explains how to do the may be purchased as applicable from any Toyota work yourself step−by−step. dealer. Areas covered include such things as spark plug re Pub.

Toyota 2003 MR2 Spyder Owner's Manual

1 2 Section -

1 2 Section -

1 5 Section -

1 9 Section -

1 10 Section -

2 Section

3 Section

Section

Section

7 2 Section -

Quick Links

Chapters

Related Manuals for Toyota 2003 MR2 Spyder

Summary of Contents for Toyota 2003 MR2 Spyder

Table of Contents