LG LMV1683ST Installation Instructions Manual
Hide thumbs
Also See for LMV1683ST:
- Service manual (49 pages) ,
- Owner's manual (30 pages) ,
- Specifications (2 pages)
Advertisement
Table of Contents
- 1 Microwave Oven
- 2 Installation Instructions
- 3 Your Safety First
- 4 Before You Start
- 5 Parts, Tools, Materials
- 6 STEP 1: Prepare the Electrical Connection
- 7 STEP 2: Prepare the Venting System
- 8 STEP 3: Prepare the Venting Blower
- 9 Wall-Vented Installation
- 10 Roof-Vented Installation
- 11 STEP 4: Prepare the Wall & Upper Cabinet
- 12 STEP 5: Install the Mounting Plate
- 13 STEP 6: Attach the Oven to the Wall
- Download this manual
Advertisement
Table of Contents
Related Manuals for LG LMV1683ST
Summary of Contents for LG LMV1683ST
-
Page 1: Microwave Oven
Website: http://www.lg.com MICROWAVE OVEN INSTALLATION INSTRUCTIONS PLEASE READ AND SAVE THESE INSTALLATION INSTRUCTIONS. P/NO.: MFL06206504... -
Page 2: Your Safety First
Your Safety First BEFORE YOU START • Proper installation is the installer's responsibility! – Read the entire manual before you begin. The model number label is located on the oven front. See Figure 1. The mounting plate is located on the upper packing. See Figure 2. NOTE: Vent grille appearance varies by model. - Page 3 Your Safety First • THIS APPLIANCE MUST BE GROUNDED! – If there is an electrical short circuit, grounding reduces the risk of electrical shock by providing an escape wire for the electric current. This appliance is equipped with a cord having a grounding wire with a grounding plug.
- Page 4 Your Safety First • MAKE SURE YOU HAVE ENOUGH SPACE AND SUPPORT. – Mount the oven against a flat, vertical wall, so it is supported by the wall. The wall should be constructed of minimum 2" x 4" wood studding and 3/8" thick drywall or plaster/lath. –...
-
Page 5: Parts, Tools, Materials
Parts, Tools, Materials THE FOLLOWING PARTS ARE SUPPLIED WITH THE OVEN: NOTE: Depending on your ventilation requirements, you may not use all of these parts. Damper/duct connector One power cord clamp and (for roof venting or wall venting installation) One dark-colored mounting screw Not Actual Size (2 pieces must be assembled as (to hold the power cord) shown) Not used if venting into kitchen. - Page 6 Parts, Tools, Materials You will need the following tools and materials for the installation: Carton or other heavy material such as a blanket for covering the counter top. Clear Tape Stud Finder or Thin Nail (for taping the templates to the wall) Keyhole Saw (for the power cord hole) Saber Saw (for cutting vent holes for roof...
-
Page 7: Step 1: Prepare The Electrical Connection
STEP 1: Prepare The Electrical Connection W A R N I N G AVOID ELECTRICAL SHOCK! THIS APPLIANCE MUST BE GROUNDED! 1. Locate the grounded electric outlet for this oven in the cabinet above the oven, as shown in Figure 5. Upper Cabinet NOTE: The outlet should be on a circuit dedicated to the... -
Page 8: Step 2: Prepare The Venting System
STEP 2: Prepare The Venting System NOTE: The ductwork you need for outside ventilation is not included with your oven. The standard ductwork fittings and length are shown in Figure 10, page 9. W A R N I N G THIS OVEN MUST BE PROPERLY VENTED! You may vent your oven in one of three ways. - Page 9 STEP 2: Prepare The Venting System Standard Fittings NOTE: If the existing duct is round, you must use a rectangular-to-round adapter, with a rectangular 3" extension duct installed between the damper assembly and the adapter to prevent the exhaust damper’s sticking. Duct Length The total length of the duct system, including straight duct, elbows, transitions, and wall or roof caps must not exceed 140 feet.
-
Page 10: Step 3: Prepare The Venting Blower
STEP 3: Prepare The Venting Blower Your microwave oven is shipped with the blower assembled for room-vented. You need to adjust the blower if you want wall-vented or roof-vented installation. W A R N I N G ELECTRICAL SHOCK HAZARD! UNPLUG UNIT BEFORE WORKING ON IT. •... -
Page 11: Wall-Vented Installation
STEP 3: Prepare The Venting Blower Blower Plate Mounting Screw WALL-VENTED INSTALLATION: Blower Plate 1. Remove one blower unit mounting screw and one or Back Plate several blower plate mounting screw(s). Remove the Blower Unit blower plate from cabinet. See Figure 12. 2. -
Page 12: Roof-Vented Installation
STEP 3: Prepare The Venting Blower blower plate mounting screws ROOF-VENTED INSTALLATION: 1. Remove one blower unit mounting screw and one or several blower plate mounting screw(s). blower plate Remove the blower plate from cabinet. See blower unit Figure 19. mounting screw Figure 19 2. -
Page 13: Step 4: Prepare The Wall & Upper Cabinet
STEP 4: Prepare The Wall & Upper Cabinet W A R N I N G To avoid personal injury or property damage, do not attempt to install this microwave oven if you cannot find a wall stud. Consult a carpenter or contractor. Measure And Track/Tape Up The Templates 1. - Page 14 STEP 4: Prepare The Wall & Upper Cabinet W A R N I N G To avoid risk of personal injury, electrical shock or death: Note where electrical outlets and electrical wires are before you drill into the wall. Locate and disconnect power to any electrical circuits that could be affected by installing this oven.
-
Page 15: Step 5: Install The Mounting Plate
STEP 5: Install The Mounting Plate 3/16 Hole on Studs The Oven Must Be Connected To At Least One 5/8 Hole on Drywall Only " Minimum 66 Wall Stud. From the Floor For Wall- 1. Center rear wall template in operating by lining up the Vented Only plumb line on wall with centerline on template.Then securely tape or tack the rear wall template in place.Make sure the... -
Page 16: Step 6: Attach The Oven To The Wall
STEP 6: Attach The Oven To The Wall W A R N I N G To avoid risk of personal injury or property damage, you will need two people to install this microwave oven. 1. Carefully lift microwave oven and hang it on support tabs (See Figure 28) at the bottom of the mounting plate.Reaching through upper cabinet, thread Power Cord... - Page 17 STEP 6: Attach The Oven To The Wall 5. Roof venting installation: See Figure 32. Install ductwork through the vent opening in the upper cabinet. Complete the venting system through the Damper roof according to the method needed. See Prepare The Venting System STEP 2.
- Page 18 Printed in China...