Advertisement
HOW TO SELECT KILOMETRES AND MILES
The console can
Console
display distance
and speed in ei-
ther kilometres or
miles. To change
the unit of mea-
surement, first
UNPLUG THE
POWER CORD.
Next, remove the
Screws
screws attaching
Console Base
the console to
the console
base. Lift the con-
sole a few inches,
being careful not
to pull on the
wires, and turn the
console over.
Switch
Locate the small
switch on the back
of the console.
Move the switch
upward or down-
ward to select kilo-
metres or miles. Re-attach the console to the console
base. After changing the unit of measurement, re-
move one of the batteries from the console for
about five seconds and then reinsert it. This will
reset the console.
HOW TO CHANGE THE INCLINE OF THE TREADMILL
To vary the intensity of your exercise, the incline of the
treadmill can be changed. There are three different in-
HOW TO FOLD AND MOVE THE TREADMILL
HOW TO FOLD THE TREADMILL FOR STORAGE
Before folding the treadmill, unplug the power cord.
CAUTION: You must be able to safely lift 20 kg (45 lbs.)
in order to raise, lower, or move the treadmill.
1. Hold the treadmill with your hands in the locations shown
at the right. To decrease the possibility of injury, bend
your legs and keep your back straight. As you raise
the treadmill, make sure to lift with your legs rather
than your back. Raise the treadmill about halfway to the
vertical position.
10
cline levels. Before changing the incline, first re-
move the key and unplug the power cord. Next, fold
the treadmill to the storage position (see HOW TO
Screws
FOLD THE TREADMILL FOR STORAGE below).
Incline
Pin
Incline
Pin
Incline Pin
Right
Incline
Leg
To change the incline, remove the incline pins from the
incline legs as shown above. Adjust the incline legs to
the desired height and fully reinsert the incline pins.
Make sure that the incline pins are in the "locked" posi-
tion shown in the inset drawing. Make sure that both
incline pins are inserted from the direction shown.
CAUTION: Before using the treadmill, make sure
that both incline pins are fully inserted at the same
height. Do not use the treadmill with the incline
pins removed.
After you have adjusted the incline legs, lower the
treadmill (see HOW TO LOWER THE TREADMILL
FOR USE on page 11).
OPERATION AND ADJUSTMENT
THE PERFORMANT LUBE
TM
WALKING BELT
Your treadmill features a walking belt coated with PERFORMANT LUBE
TANT: Never apply silicone spray or other substances to the walking belt or the walking platform. Such
substances will deteriorate the walking belt and cause excessive wear.
HOW TO PLUG IN THE POWER CORD
This product must be earthed. If it should malfunction or break
down, earthing provides a path of least resistance for electric
current to reduce the risk of electric shock. This product is equipped
with a cord having an equipment-earthing conductor
and an earthing plug.
Two power cords are included. Select the one that will fit your
outlet. Refer to drawing 1. Plug the indicated end of the power
cord into the socket on the treadmill. Refer to drawing 2. Plug
the power cord into an appropriate outlet that is properly in-
stalled and earthed in accordance with all local codes and or-
dinances. Note: In Italy, an adapter (not included) must be
used between the power cord and the outlet. Important: The
treadmill is not compatible with GFCI-equipped outlets.
Use only a power cord type H05VV-F with a conductor of at least
1mm
2
, with a country recognised plug and an appliance coupler.
DANGER:
Improper connection of the
equipment-earthing conductor can result in an in-
creased risk of electric shock. Check with a qualified
electrician or serviceman if you are in doubt as to
whether the product is properly earthed. Do not modify
the plug provided with the product—if it will not fit the
outlet, have a proper outlet installed by a qualified elec-
trician.
TM
, a high-performance lubricant. IMPOR-
1
Socket on treadmill
2
Outlet
7
Advertisement
