Sony CDX-M800 Service Manual
  1. Manuals
  2. Brands
  3. Sony Manuals
  4. CD Player
  5. CDX-M800
  6. Service manual
Sony CDX-M800 Service Manual

Sony CDX-M800 Service Manual

Hide thumbs Also See for CDX-M800:
Table of Contents

Advertisement

Quick Links

Download this manual
SERVICE MANUAL
Ver 1.1 2003. 05
• The tuner and CD sections have no adjustments.
SPECIFICATIONS
AUDIO POWER SPECIFICATIONS (US MODEL)
POWER OUTPUT AND TOTAL HARMONIC DISTORTION
23.2 watts per channel minimum continuous average power into
4 ohms, 4 channels driven from 20 Hz to 20 kHz with no more
than 5% total harmonic distortion.
CD player section
Signal-to-noise ratio
90 dB
Frequency response
10 – 20,000 Hz
Wow and flutter
Below measurable limit
Tuner section
FM
Tuning range
87.5 – 107.9 MHz (US, Canadian model)
87.5 – 108.0 MHz (AEP, UK, E model)
Antenna terminal
External antenna connector
Intermediate frequency 10.7 MHz/450 kHz
Usable sensitivity
9 dBf
Selectivity
75 dB at 400 kHz
Signal-to-noise ratio
67 dB (stereo),
69 dB (mono)
Harmonic distortion at 1 kHz
0.5% (stereo),
0.3% (mono)
Separation
35 dB at 1 kHz
Frequency response
30 – 15,000 Hz
AM (US, Canadian model)
Tuning range
530 – 1,710 kHz
Antenna terminal
External antenna connector
Intermediate frequency 10.7 MHz/450 kHz
Sensitivity
30 µV
Sony Corporation
9-874-299-02
2003E04-1
e Vehicle Company
© 2003. 05
Published by Sony Engineering Corporation
CDX-M800
Model Name Using Similar Mechanism
CD Drive Mechanism Type
Optical Pick-up Name
MW/LW (AEP, UK, E model)
Tuning range
MW: 531 – 1,602 kHz
LW: 153 – 279 kHz
Aerial terminal
External aerial connector
Intermediate frequency 10.7 MHz/450 kHz
Sensitivity
MW: 30 µV
LW: 40 µV
Power amplifier section
Outputs
Speaker outputs (sure seal connectors)
Speaker impedance
4 – 8 ohms
Maximum power output 52 W × 4 (at 4 ohms)
General
Outputs
Audio outputs (front/rear)
Subwoofer output (mono)
Power antenna relay
control terminal (US, Canadian model)
Power aerial relay
control terminal (AEP, UK, E model)
Power amplifier control
terminal
FM/AM COMPACT DISC PLAYER
FM/MW/LW COMPACT DISC PLAYER
US Model
Canadian Model
AEP Model
UK Model
E Model
CDX-L410X/L490X
MG-393XC-121//K
KSS-721A
– Continued on next page –
US, Canadian Model
AEP, UK, E Model
1

Advertisement

Table of Contents
loading

Related Manuals for Sony CDX-M800

Summary of Contents for Sony CDX-M800

  • Page 1 External antenna connector Intermediate frequency 10.7 MHz/450 kHz FM/AM COMPACT DISC PLAYER Sensitivity 30 µV US, Canadian Model FM/MW/LW COMPACT DISC PLAYER AEP, UK, E Model Sony Corporation 9-874-299-02 2003E04-1 e Vehicle Company © 2003. 05 Published by Sony Engineering Corporation...

  • Page 2: Service Notes

    LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.
  • Page 3 CDX-M800 AEP, UK, E model: Notes on CD-R/CD-RW discs • You can play CD-Rs (recordable CDs)/CD-RWs (rewritable CDs) designed for audio use on this unit. Look for these marks to distinguish CD-Rs/CD-RWs for audio use. This label is located on the bottom of the chassis.
  • Page 4 CDX-M800 EXTENSION CABLE AND SERVICE POSITION When repairing or servicing this set, connect the jig (extension cable) as shown below. • Connect the MAIN board (CNP301) and the SERVO board (CN1) with the extension cable (Part No. J-2502-062-1). MAIN BOARD CNP301...

  • Page 5: Table Of Contents

    CDX-M800 TABLE OF CONTENTS 1. GENERAL 4. DIAGRAMS Location of Controls ..............6 4-1. IC Pin Descriptions ............18 Connection example (US, Canadian Model) ......6 4-2. Block Diagram –CD Section– ........... 21 Connections (US, Canadian Model) ........7 4-3. Block Diagram –Tuner Section– ........22 4-4.

  • Page 6: General

    *1 When an optional MD unit is connected. t EQ7 button b Main display window g SEEK (</,) buttons *2 Available only when an optional Sony portable u SOUND button c IMAGE button 20 device is connected to BUS AUDIO IN of the unit.

  • Page 7: Connections (Us, Canadian Model)

    CDX-M800 Connections (US, Canadian Model) Source selector (not supplied) Sélecteur de source Supplied with the CD/MD changer (non fourni) Fourni avec le changeur de CD/MD Selector de fuente Suministrado con el cambiador de CD/MD (no suministrado) XA-C30 BUS AUDIO IN...

  • Page 8: Disassembly

    CDX-M800 SECTION 2 DISASSEMBLY Note : This set can be disassemble according to the following sequence. 2-7. CHASSIS (T) SUB ASSY 2-1. FRONT PANEL ASSY (Page 11) (Page 8) 2-8. LEVER SECTION, 2-2. CD MECHANISM BLOCK, IN SELF SW BOARD...

  • Page 9: Cd Mechanism Block, Front Panel Assy

    CDX-M800 2-2. CD MECHANISM BLOCK, FRONT PANEL ASSY 7 bracket (CD) 5 CD mechanism block 6 PTT 2.6x6 8 tension spring (flexible) 0 cover (flexible) 9 slider (flexible) 3 PTT 2.6x4 qa CNP909 slider (flexible) flexible board Note: When installing the flexible board, 2 PTT 2.6x4...

  • Page 10: Motor Block Assy, Cam (R) Assy

    CDX-M800 2-4. MOTOR BLOCK ASSY, CAM (R) ASSY Note : Install the motor block assy and cam (R) assy in this roder. For phase alignment between cams (L) and (R), see page 15 and 17. 1 PTT 2.6x6 Note: Install the cam (R) assy with 4 PTT 2.6x6...

  • Page 11: Heat Sink

    CDX-M800 2-6. HEAT SINK 5 heat sink 4 PTT 2.6x6 3 PTT 2.6x12 1 PTT 2.6x6 2 PTT 2.6x6 2-7. CHASSIS (T) SUB ASSY 2 P 2x3 3 P 2x3 1 Unsolder the 4 chassis (T) sub assy lead wires.

  • Page 12: Lever Section, In Self Sw Board

    CDX-M800 2-8. LEVER SECTION, IN SELF SW BOARD 5 guide (disc) 6 lever (R) 3 tension spring (LR) 7 lever (L) 1 special screw 2 IN SELF SW board 4 claws 2-9. SERVO BOARD 8 SERVO board 7 special screw 6 special screws 2 Removal the solders.

  • Page 13: Shaft Roller Assy, Load Sw Board

    CDX-M800 2-10. SHAFT ROLLER ASSY, LOAD SW BOARD 3 retaining ring (RA) shaft retainer (roller) washer retaining 4 shaft retainer (roller) washer shaft retainer ring (RA) (roller) Fig. 1 6 special screw 5 shaft roller assy 2 arm (roller) 7 LOAD SW board 1 tension spring (RA) 2-11.

  • Page 14: Optical Pick-Up Block

    CDX-M800 2-12. OPTICAL PICK-UP BLOCK 4 screw 1 P 2x3 5 plate spring (feed) 2 sled motor assy 3 optical pick-up block 6 shaft (feed) assy...

  • Page 15: Phase Alignment

    CDX-M800 SECTION 3 PHASE ALIGNMENT 3-1. ARM (A-L) ASSY, ARM (B-L) ASSY 3 arm (A-L) assy 4 type-E stop ring 1.5 2 type-E stop ring 1.5 1 arm (B-L) assy bracket (L) assy 3-2. CAM (L) 1 Move the arm (B-L) assy in the direction of the arrow A and the arm (A-L) assy in the direction of 3 type-E stop ring 1.5...

  • Page 16: Motor Block

    CDX-M800 3-3. MOTOR BLOCK 1 Turn the cam (L) and position the cam so that part A does not touch the SW board SW900. 3 PTT 2.6x6 4 PTT 2.6x6 2 motor block SWITCH board 5 PTT 2.6x6 SW900 cam (L) 3-4.

  • Page 17: Arm (A-R) Assy, Arm (B-R) Assy

    CDX-M800 3-5. ARM (A-R) ASSY, ARM (B-R) ASSY 4 type-E stop ring 1.5 3 arm (A-R) assy 2 type-E stop ring 1.5 1 arm (B-R) assy bracket (R) assy 3-6. CAM (R) 3 type-E stop ring 1.5 1 Move the arm (B-R) assy in the direction of the arrow A and the arm (A-R) assy in the direction of the arrow B fully (full open state).

  • Page 18: Diagrams

    Electronic volume mute signal output I2C CKO Tuner/E-volume BUS clock output I2C SIO Tuner/E-volume BUS data output UNI SO SONY BUS data output UNI SI SONY BUS data input UNI CKO SONY BUS clock output TUNER ATT Tuner attenuate signal output...
  • Page 19 CDX-M800 Pin No. Pin Name Pin Description DST SEL2 Destination select signal input CD LM LO CD loading motor control signal output CD LM EJ CD eject motor control signal output CD RST CD servo reset signal output CD AO CD servo command/parameter discri.
  • Page 20 CDX-M800 • IC2 M30823MH-066GP (US, Canadian model) (DISPLAY SYSTEM CONTROL) (DISPLAY Board) • IC2 M30823MH-073GP (AEP, UK, E model) (DISPLAY SYSTEM CONTROL) (DISPLAY Board) Pin No. Pin Name Pin Description SYS RST Main chip enable input Not used. (Open) FL DATA3 FL serial data output Not used.

  • Page 21: Block Diagram -Cd Section

    CDX-M800 4-2. BLOCK DIAGRAM — CD SECTION — RF AMP,DIGITAL SERVO DIGITAL SIGNAL PROCESSOR OPTICAL PICK-UP KSS-721A (Page 22) TUNER SECTION LOUT SYSTEM CONTROL ROUT IC303 (1/3) CONV R-CH DEMOD PACK TSTB DSUB CODE TSCK PROCESS CONV. CD TSO FORCUS...

  • Page 22: Block Diagram -Tuner Section

    CDX-M800 Ver 1.1 4-3. BLOCK DIAGRAM — TUNER SECTION — PJ401 –1 BUS AUDIO ELECTRONIC VOLUME –2 IC401 Q408 R-CH SECTION –5 4 PDL (Page 21) 42 MDL AUDIO OUT –6 32 AC OUT L FRONT Q171 R-CH TUNER UNIT...

  • Page 23: Block Diagram -Display Section

    CDX-M800 4-4. BLOCK DIAGRAM — DISPLAY SECTION — BUS INTERFACE SYSTEM CONTROL IC301 IC303 (3/3) CNP102 (BUS CONTROL IN) UNI SI DATA SIRCS 1 RECEIVE IC62 UNI SO D513 UNI CKO RECEIVE IC503 64 BUS ON KEY IN0 85 KEY IN...

  • Page 24: Circuit Boards Location

    CDX-M800 4-5. CIRCUIT BOARDS LOCATION THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. (In addition to this, the necessary note is printed in each block.) IN SELF SW board SL SW board for schematic diagram: • All capacitors are in µF unless otherwise noted. pF: µµF...

  • Page 25: Schematic Diagram -Cd Mechanism Section

    CDX-M800 • Refer to page 24 for Waveforms. 4-6. SCHEMATIC DIAGRAM — CD MECHANISM SECTION — • Refer to page 36 for IC Block Diagram. TP77 TP78 TP89 TP79 TP80 TP81 TP82 TP45 TP10 TP83 TP44 TP43 TP84 TP42 TP41...

  • Page 26: Printed Wiring Boards -Cd Mechanism Section

    CDX-M800 4-7. PRINTED WIRING BOARDS — CD MECHANISM SECTION — • Refer to page 24 for Circuit Boards Location.
  • Page 27 CDX-M800 TP77 TP78 TP62 TP63 TP82 TP84 TP48 TP80 TP66 TP83 TP81 TP60 TP11 TP50 TP12 TP47 TP64 TP10 TP51 TP59 TP89 TP52 TP70 TP71 TP56 (Page 29) TP72 TP58 TP22 TP23 TP24 TP61 TP25 TP76 TP88 TP74 TP69 TP68...

  • Page 28: Printed Wiring Boards -Main Section

    CDX-M800 Ver 1.1 4-8. PRINTED WIRING BOARDS — MAIN SECTION — • Refer to page 24 for Circuit Boards Location. • Semiconductor Location Ref. No. Location Ref. No. Location (D101) E-10 D831 (D832) (D102) E-10 (D103) E-10 (D843) (D104) D-10...
  • Page 29 CDX-M800 Ver 1.1 PJ401 CNJ101 CNP102 CNP101 C205 FB101 F901 IC201 FB102 R446 R445 R408 R442 C101 TUX501 CN904 R441 R440 R443 R410 CN903 R103 D106 C103 C442 R502 C505 C503 D116 C506 C226 BATT AEP,UK model L101 C508 L503...

  • Page 30: Schematic Diagram -Main Section (1/2)

    CDX-M800 Ver 1.1 • Refer to page 24 for Waveform. 4-9. SCHEMATIC DIAGRAM — MAIN SECTION (1/2) — • Refer to page 36 for IC Block Diagrams. R440 R444 C278 R203 C206 R204 C207 C178 R439 R443 C288 PJ401 R442...

  • Page 31: Schematic Diagram -Main Section (2/2)

    CDX-M800 Ver 1.1 • Refer to page 24 for Waveform. 4-10. SCHEMATIC DIAGRAM — MAIN SECTION (2/2) — • Refer to page 36 for IC Block Diagrams. (Page 30) IC B/D Q101 D104 CNP102 IC301 TH100 C303 L301 R102 R101...

  • Page 32: Printed Wiring Board -Sub Section

    CDX-M800 Ver 1.1 4-11. PRINTED WIRING BOARD — SUB SECTION — • Refer to page 24 for Circuit Boards Location. C535 C536 C537 R509 R538 D506 C540 C539 D511 Q504 D507 C538 R536 IC503 SW501 R533 FB503 D512 Q503 R531...

  • Page 33: Schematic Diagram -Sub Section

    CDX-M800 Ver 1.1 4-12. SCHEMATIC DIAGRAM — SUB SECTION — • Refer to page 37 for IC Block Diagrams. CN502 Q503 R532 R535 R534 R531 R533 Q504 D512 SW501 D513 D514 C536 (Page 31) R536 R537 R538 CN501 C537 C541...

  • Page 34: Printed Wiring Board -Display Section

    CDX-M800 Ver 1.1 4-13. PRINTED WIRING BOARD — DISPLAY SECTION — • Refer to page 24 for Circuit Boards Location. FL900 R971 C905 LED931 LED909 R999 R988 FMA12 C962 R994 R989 FMA10 FB914 R981 C912 S931 S909 D901 FB913 C908...

  • Page 35: Schematic Diagram -Display Section

    CDX-M800 Ver 1.1 • Refer to page 24 for Waveform. 4-14. SCHEMATIC DIAGRAM — DISPLAY SECTION — • Refer to page 37 for IC Block Diagrams. R936 R950 R946 R952 R945 R954 R951 R956 R953 R958 R955 R960 R957 R961...

  • Page 36: Ic Block Diagrams

    CDX-M800 4-15. IC BLOCK DIAGRAMS IC1 µPD63711GC-8EU (SERVO Board) IC2 BA5810FP-E2 (SERVO Board) 71 70 BIAS LOADING PRE MICROCOMPUTER INTERFACE OPIN4+ FWD REV AGCI 50 C2D3 – OPIN4– COMPARATOR 49 C2D2 LDCONT CD-TEXT DECODER 48 C2D1 POWER OPOUT4 SUB-CODE PROCESSOR...
  • Page 37 CDX-M800 IC201 TDA8588J/N1 (MAIN Board (1/2)) I2C BUS PGND3 IN_RL IN_FL SGND PROTECTION DIAGNOSTIC IN_FR IN_RR ACGND PGND2 STANDBY MUTE CHIP DETECT DIAGNOSTIC PGND1 BATTERY TEMPERATURE DIAG DETECTION PROTECTION ENABLE LOGIC SWITCH CRES SWITCH AU8V SERVO MECHA DISP+B REFERENCE VOLTAGE...
  • Page 38 CDX-M800 IC401 TDA7416 (MAIN Board (1/2)) 30 29 24 23 HIGH PASS MIXER FILTER2 SOFT STEP FADER ACOUTR SOFT STEP ACINSW FADER ACOUTSW HIGH PASS MIXER 22 OUTRF FILTER WOOFER SOFT STEP OUTRR FILTER FADER 7 BAND EQUALIXER 20 AC2INR...

  • Page 39: Exploded Views

    CDX-M800 Ver 1.1 SECTION 5 EXPLODED VIEWS NOTE: • The mechanical parts with no reference The components identified by • Color Indication of Appearance Parts mark 0 or dotted line with mark number in the exploded views are not supplied.

  • Page 40: Cam Section

    CDX-M800 5-2. CAM SECTION M601 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 3-230-495-01 CAM (L) 3-230-494-01 GEAR (C) X-3380-549-1 ARM (B-R) ASSY 3-230-496-01 CAM (R) X-3380-544-2 BRACKET (L) ASSY X-3380-545-2 BRACKET (R) ASSY X-3380-548-1 ARM (B-L) ASSY...

  • Page 41: Main Board Section

    CDX-M800 Ver 1.1 5-3. MAIN BOARD SECTION supplied not supplied TUX501 F901 not supplied not supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 3-230-493-01 GEAR (DRIVE SHAFT) 1-777-246-41 CORD (WITH CONNECTOR) (ANTENNA) 3-230-444-01 GUIDE (DRIVE SHAFT)

  • Page 42: Front Panel Section

    CDX-M800 Ver 1.1 5-4. FRONT PANEL SECTION not supplied FL900 LCD2 not supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark X-3383-765-1 PANEL (KEY) ASSY (S), FRONT (US,CND) 3-248-791-01 BUTTON (OPEN) X-3383-767-1 PANEL (KEY) ASSY (S), FRONT (AEP,UK,E)

  • Page 43: Cd Mechanism Section (1)

    CDX-M800 5-5. CD MECHANISM SECTION (1) (MG-393XC-121//K) M903 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 1-683-283-11 IN SELF SW BOARD 3-221-779-02 BRACKET (MOTOR) 3-040-039-03 CHASSIS (T) 3-040-034-01 SPRING (RA), TENSION 3-040-038-01 SPRING (LR), TENSION 3-040-042-01 WASHER...

  • Page 44: Cd Mechanism Section (2)

    CDX-M800 5-6. CD MECHANISM SECTION (2) (MG-393XC-121//K) not supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 3-040-025-02 ARM, CHUCKING 3-040-033-01 SPRING (KF1), TENSION 3-040-031-01 DAMPER (T) A-3307-422-A CHASSIS (M) COMPLETE ASSY 3-040-056-01 LEVER (D) 3-040-059-01 SPRING (TR), TENSION...

  • Page 45: Cd Mechanism Section (3)

    CDX-M800 5-7. CD MECHANISM SECTION (3) (MG-393XC-121//K) M901 M902 The components identified by Les composants identifiés par une mark 0 or dotted line with mark marque 0 sont critiques pour 0 are critical for safety. la sécurité. Replace only with part number Ne les remplacer que par une piéce...

  • Page 46: Electrical Parts List

    CDX-M800 Ver 1.1 SECTION 6 DISPLAY ELECTRICAL PARTS LIST NOTE: • Due to standardization, replacements in • Items marked “*” are not stocked since The components identified by mark 0 or dotted line with mark the parts list may be different from the they are seldom required for routine service.
  • Page 47 CDX-M800 Ver 1.1 DISPLAY Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < JUMPER RESISTOR > R916 1-218-859-11 RES-CHIP 3.3K 1/16W R917 1-218-855-11 RES-CHIP 2.2K 1/16W FL924 1-216-864-11 METAL CHIP 1/10W R918 1-218-851-11 RES-CHIP 1.5K 1/16W...
  • Page 48 CDX-M800 Ver 1.1 DISPLAY IN SELF SW LOAD SW MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R991 1-218-855-11 RES-CHIP 2.2K 1/16W C183 1-128-428-11 ELECT 10uF R992 1-218-855-11 RES-CHIP 2.2K 1/16W C188 1-162-927-11 CERAMIC CHIP...
  • Page 49 CDX-M800 Ver 1.1 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C341 1-124-589-11 ELECT 47uF C810 1-128-416-11 ELECT CHIP 100uF C342 1-164-156-11 CERAMIC CHIP 0.1uF C901 1-124-234-00 ELECT 22uF C401 1-124-589-11 ELECT 47uF C903 1-164-156-11 CERAMIC CHIP 0.1uF...
  • Page 50 CDX-M800 Ver 1.1 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark D825 8-719-978-33 DIODE DTZ-TT11-6.8B Q103 8-729-901-81 TRANSISTOR 2SC2412K-T-146-R D826 8-719-978-33 DIODE DTZ-TT11-6.8B Q171 8-729-920-21 TRANSISTOR DTC314TK-T-146 D827 8-719-978-33 DIODE DTZ-TT11-6.8B Q181 8-729-920-21 TRANSISTOR DTC314TK-T-146 D828 8-719-978-33 DIODE DTZ-TT11-6.8B...
  • Page 51 CDX-M800 Ver 1.1 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R303 1-216-864-11 METAL CHIP 1/10W R377 1-216-845-11 METAL CHIP 100K 1/10W R304 1-216-809-11 METAL CHIP 1/10W R380 1-216-809-11 METAL CHIP 1/10W R305 1-216-809-11 METAL CHIP...
  • Page 52 CDX-M800 Ver 1.1 MAIN SERVO Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R807 1-218-703-11 METAL CHIP 0.5% 1/10W 1-162-966-11 CERAMIC CHIP 0.0022uF 10% R808 1-216-833-11 METAL CHIP 1/10W 1-107-826-11 CERAMIC CHIP 0.1uF R809 1-216-864-11 METAL CHIP...
  • Page 53 CDX-M800 Ver 1.1 SERVO SL SW SWITCH Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < VIBRATOR > MISCELLANEOUS *************** 1-795-520-11 VIBRATOR, CERAMIC (16.9344MHz) 1-776-207-72 CORD (WITH CONNECTOR) (POWER) ************************************************************* (US,CND,E) 1-683-282-11 SL SW BOARD 1-776-527-71 CORD (WITH CONNECTOR) (ISO) (POWER)
  • Page 54 CDX-M800 Ver 1.1 Ref. No. Part No. Description Remark PARTS FOR INSTALLATION AND CONNECTIONS *************************************** X-3382-647-1 FRAME ASSY, FITTING X-3366-405-1 SCREW ASSY (EXP), FITTING (AEP,UK,E) X-3382-821-1 COLLAR ASSY 3-934-325-01 SCREW (+K 5X8 TP) (US,CND,E) 1-465-459-21 ADAPTOR, ANTENNA (AEP,UK) 1-776-207-72 CORD (WITH CONNECTOR) (POWER)
  • Page 55 CDX-M800 MEMO...
  • Page 56 CDX-M800 REVISION HISTORY Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper on the revised page allows you to jump to the next revised page. Ver. Date Description of Revision 2003. 01 2003.

Table of Contents