Installation And Connections; System Installation; Audio Equipment Connections; Video Equipment Connections - Harman Kardon AVR325 Service Manual

AVR325

System Installation

After unpacking the unit, locating it in a place with ade-
quate ventilation and placing it on a solid surface capable
of supporting its weight, you will need to make the con-
nections to your audio and video equipment.
IMPORTANT NOTE: For your personal safety and to
avoid possible damage to your equipment and speakers,
it is always a good practice to turn off and unplug the
AVR and ALL source equipment from the AC output
before making any audio or video system connections.

Audio Equipment Connections

We recommend that you use high-quality interconnect
cables when making connections to source equipment
and recorders to preserve the integrity of the signals.
1. Connect the analog output of a CD player to the
31
CD Audio Inputs .
NOTE: When the CD player has both fixed and vari-
able audio outputs, it is best to use the fixed output
unless you find that the input to the receiver is so low
that the sound is noisy, or so high that it is distorted.
2. Connect the analog Play/Out jacks of a cassette
deck, MD, CD-R or other audio recorder to the Tape
34
Input Jacks . Connect the analog Record/In jacks
on the recorder to the Tape Output Jacks
the AVR 325.
3. Connect the output of any digital sources such as
a CD or DVD changer or player, advanced video
game, a digital satellite receiver, HDTV tuner or digital
cable set-top box or the output of a compatible
computer sound card to the Optical and Coaxial
&*.
Digital Audio Inputs
33 36
4. Connect the coaxial or optical Digital Audio Outputs
ik on the rear panel of the AVR 325 to the matching
digital input connections on a CD-R or MiniDisc recorder.
5. Assemble the AM Loop Antenna supplied with the
unit. Connect it to the AM and GND Screw
Terminals ¡.
6. Connect the supplied FM antenna to the FM (75-
ohm) Connection ™. The FM antenna may be an
external roof antenna, an inside powered or wire-lead
antenna or a connection from a cable TV system. If
the antenna or connection uses 300-ohm twin-lead
cable, you must use the 300-ohm-to-75-ohm adapter
supplied with the unit to make the connection.

INSTALLATION AND CONNECTIONS

7. Connect the front, center, surround and surround
back speaker outputs §¶ª‚ to the respective
speakers.
To ensure that all the audio signals are carried to your
speakers without loss of clarity or resolution, we sug-
gest that you use high-quality speaker cable. Many
brands of cable are available and the choice of cable
may be influenced by the distance between your
speakers and the receiver, the type of speakers you
use, personal preferences and other factors. Your dealer
or installer is a valuable resource to consult in select-
ing the proper cable.
Regardless of the brand of cable selected, we recom-
mend that you use a cable constructed of multistrand
copper with a gauge of 14 or smaller. Remember that
in specifying cable, the lower the number, the thicker
the cable.
Cable with a gauge of 16 may be used for short runs
of less than 10 feet. We do not recommend that you
use cables with an AWG equivalent of 18 or higher,
due to the power loss and degradation in performance
that will occur.
Cables that are run inside walls should have the appro-
priate markings to indicate listing with UL, CSA or other
appropriate testing agency standards. Questions about
on
35
running cables inside walls should be referred to your
installer or a licensed electrician who is familiar with
the NEC and/or the applicable local building codes in
your area.
When connecting wires to the speakers, be certain to
observe proper polarity. Note that the positive (+) ter-
minal of each speaker connection now carries a spe-
cific color code, as noted on page 8. However, most
speakers still use a red terminal for the positive (+)
connection. Connect the "negative" or "black" wire
to the same terminal on both the receiver and the
speaker.
NOTE: While most speaker manufacturers adhere to
an industry convention of using black terminals for
negative and red ones for positive, some may vary
from this configuration. To ensure proper phase and
optimal performance, consult the identification plate on
your speaker or the speaker's manual to verify polarity.
If you do not know the polarity of your speaker, ask
your dealer for advice before proceeding, or consult
the speaker's manufacturer.
We also recommend that the length of cable used
to connect speaker pairs be identical. For example,
use the same length piece of cable to connect the
front-left and front-right or surround-left and sur-
round-right speakers, even if the speakers are a
different distance from the AVR 325.
8. Connections to a subwoofer are normally made via
a line-level audio connection from the Subwoofer
Output ¢ to the line-level input of a subwoofer with
a built-in amplifier. When a passive subwoofer is used,
the connection first goes to a power amplifier, which
will be connected to one or more subwoofer speakers.
If you are using a powered subwoofer that does not
have line-level input connections, follow the instruc-
tions furnished with the speaker for connection infor-
mation.
9. If an external multichannel audio source with 5.1
outputs such as an external digital processor/decoder,
DVD-Audio or SACD player is used, connect the
outputs of that device to the 8-Channel Direct
Inputs

Video Equipment Connections

Video equipment is connected in the same manner as
audio components. Again, the use of high-quality inter-
connect cables is recommended to preserve signal
quality.
1. Connect a VCR's or other video source's audio and
video Play/Out jacks to the Video 1/Video 2 Audio
and Video Input Jacks fl°
panel. The Audio and Video Record/In jacks on the
VCR should be connected to the Video 1/Video 2
Audio and Video Output Jacks ‡·
the AVR 325.
2. Connect the analog audio and video outputs of a
satellite receiver, cable TV converter, television set or
any other video source to the Video 3 Audio and
Video Input Jacks a
3. Connect the analog audio and video outputs of a
DVD or laser disc player to the DVD Audio and
Video Inputs fi
4. Connect the digital audio outputs of a DVD player,
satellite receiver, cable box or HDTV converter to the
appropriate Optical or Coaxial Digital Inputs
&*.
36
5. Connect the Video Monitor Output › jacks on
the receiver to the composite or S-Video input of your
television monitor or video projector.
6. If your DVD player and monitor both have compo-
nent video connections, connect the component out-
puts of the DVD player to the DVD Component
Video Inputs c. Even when component video con-
nections are used, the audio connections should still
be made to either the analog DVD Audio Inputs
or any of the Optical or Coaxial Digital Input Jacks
33 36
7. If other devices with component video outputs are
available, connect it to the Video 2 Component
Video Inputs d. The audio connections for this
14
14
harman/kardon
.
40
on the rear
37 39
38 41
42 .
32 .
.
on
33
32