Table of Contents
Advertisement
40725 rev4
28/8/07
A
B B
C C
15:32
Page 5
FILLING
A
A
1 1
Make sure that the iron is not
plugged in, then set the steam
to dry iron selector switch ⁄
the position before filling the iron
with water.
2 2
Lift up the filler cap and fill the
tank ‡
‡ with water through the
filling hole ‰
‰ , using the beaker
provided (300ml). A
A Â
filling replace the filler cap. In
hard water areas the use of
distilled or demineralised water
is recommended.
W W A A R R N N I I N N G G : : N N e e v v e e r r u u s s e e b b a a t t t t e e r r y y
t t o o p p p p i i n n g g u u p p f f l l u u i i d d o o r r w w a a t t e e r r
c c o o n n t t a a i i n n i i n n g g a a n n y y s s u u b b s s t t a a n n c c e e s s
l l i i k k e e s s t t a a r r c c h h , , o o r r s s u u g g a a r r , , o o r r
d d e e f f r r o o s s t t e e d d w w a a t t e e r r f f r r o o m m a a
r r e e f f r r i i g g e e r r a a t t o o r r . .
3 3
Always pour out the remaining
water after use.
W W A A R R N N I I N N G G : : W W h h e e n n f f i i l l l l i i n n g g y y o o u u r r
i i r r o o n n w w i i t t h h t t a a p p w w a a t t e e r r a a l l w w a a y y s s
u u s s e e t t h h e e b b e e a a k k e e r r p p r r o o v v i i d d e e d d . .
N N e e v v e e r r f f i i l l l l d d i i r r e e c c t t l l y y u u n n d d e e r r t t h h e e
t t a a p p . .
TEMPERATURE
CONTROL
B B
Plug in the iron and switch on.
Set the temperature control dial
¤ to the temperature required,
¤
but don't start ironing
immediately.
If you wait a few minutes, the
iron will stabilise at the required
setting. Your Morphy Richards
iron is fitted with an indicator
light fl
fl which will go on and off
while you are ironing.
This is perfectly normal as it
shows that the iron is
maintaining the heat setting you
have chosen.
It is always a good idea to begin
with cool fabrics and work up to
higher settings.
An iron heats up quicker than it
cools down so you'll save time
and electricity.
w w w w w w . . m m o o r r p p h h y y r r i i c c h h a a r r d d s s . . c c o o m m
FEATURES OF YOUR
IRON
Temperature indicator
⁄ to
light
The indicator light fl
the iron is warming up. When
the required temperature is
reached the light will go out and
 After
will cycle on-off during
operation.
Dry ironing
You can use your iron as a dry
iron only. Make sure the steam
to dry iron selector switch ⁄
set to the
Any temperature setting may be
used depending on the
garment. The spray feature may
be used provided there is water
in the tank (see filling section).
You do not need to put any
water in the tank when dry
ironing only.
Spray
Press the spray button ›
aim the spray of water at
stubborn creases. You can do
this whilst dry ironing providing
there is water in the tank. When
using the water spray it may be
necessary to push the button a
few times to get the spray pump
primed.
Automatic variable
steam
Fill the iron with water as
described in the filling section,
and insert the plug into the
electrical socket.
1 1
Set the 'steam to dry iron'
selector switch to steam ⁄
2 2
Select the temperature required
by turning the temperature
control dial ¤
setting. The amount of steam
required is automatically
selected and is displayed in
window ‹
fl shows that
⁄ is
symbol.
C C
› and
B B
⁄ .
¤ to the desired
‹ .
5 5
Advertisement
Table of Contents
