Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Zenoah G6200
Summary of Contents for Zenoah G6200
- Page 1 G6200 115 40 22-38 (010) OWNER’S MANUAL CHAIN SAW G6200 GB-1...
-
Page 2: Table Of Contents
G6200 EXPLANATION OF SYMBOLS AND SAFETY WARNINGS Read operator's instruction Wear head, eye and ear book before operating this protection. machine. Use the chain saw Warning! Danger of with two hands. kickback. Read, understand and Never touch hot surface. follow all warnings. -
Page 3: For Safe Operation
G6200 1. For safe operation WARNING This chainsaw has been especially designed for tree maintenance and should therefore only be used by trained operators when working on trees. 1. Never operate a chain saw when you are fatigued, ill, or upset, or under the influence of medication that may 10. - Page 4 G6200 20. Operate the chain saw only in well handle, and the left hand on the front ventilated areas. Never start or run handle, when the engine is running. the engine inside a closed room or Use a firm grip with thumbs and fin-...
-
Page 5: Explanation Of Symbols On The Machine
G6200 2. Explanation of Symbols on the Machine WARNING • For safe operation and maintenance, symbols are carved in relief on the machine. According to these indications, please be careful not to make any mistake. The port to refuel “MIX GASOLINE”... -
Page 6: Installing Guide Bar And Saw Chain
G6200 3. Installing Guide Bar and Saw Chain A standard saw unit package contains the items as illustrated. Power unit Plug wrench Hexagon socket (S13/S19) + Slotted driver) Screwdriver for carburetor adjustment (Slotted driver) Bar protector Guide bar Saw chain Open the box and install the guide bar and the saw 5. -
Page 7: Fuel And Chain Oil
3. Fasten the fuel cap securely and wipe up any fuel spillage around the unit. WARNING • The Zenoah engines are lubricated by oil specially formulated for air-cooled 2-cycle gasoline engine use. 1. Select flat and bare ground for fueling. -
Page 8: Operating The Engine
G6200 5. Operating the Engine 7. Allow the engine to warm up with the throttle lever WARNING pulled slightly. • It is very dangerous to run a chainsaw that mounts broken parts or lacks any parts. WARNING Before starting engine, make sure that all the parts including bar and chain are installed properly. - Page 9 G6200 1. Stop engine and screw in both H and L needles In case the brake is not effective, ask our dealer for until they stop. Never force. Then set them back the inspection and repairs. standard number of turns as shown below.
-
Page 10: Sawing
G6200 6. Sawing I -2 seconds and pushing the front WARNING hand guard forward. The chain should stop immediately with the • Before proceeding to your job, engine at full speed. If the chain is read the section “For Safe slow to stop or does not stop, re- Operation”. - Page 11 G6200 A log lying on the ground First check to which side the limb is bent. Then make the initial cut from the bent side and finish by sawing from the opposite side. WARNING • Be alert to the springing back of a cut limb.
-
Page 12: Maintenance
G6200 7. Maintenance ■ PERIODICAL SERVICE POINTS WARNING 1. Cylinder fins Dust clogging between the cylinder fins will cause • Before cleaning, the inspecting or repairing the overheating of the engine. Periodically check and clean unit, make sure that engine has stopped and is cool. -
Page 13: Maintenance Of Saw Chain And Guide Bar
G6200 8. Maintenance of Saw Chain and Guide Bar ■ Saw Chain WARNING WARNING • Be sure to round off the front edge to reduce the chance of kickback or tie-strap breakage. • It is very important for smooth and safe operation to always keep the cutters sharp. -
Page 14: Troubleshooting Guide
G6200 9. Troubleshooting Guide Case 1. Starting failure Case 3. Oil does not come out Check oil for sub- WARNING Replace. standard quality. • Make sure the icing prevention system is not working. Check fuel for water Check oil passage... -
Page 15: Specifications
G6200 11. Specifications Power unit: Displacement (cm ): ............................62.0 Fuel: ........................Mixture (Gasoline 50 : Two-cycle oil 1) (when using ZENOAH genuine oil) Fuel tank capacity (cm ): ............................670 Chain oil: ...........................Motor oil SAE# 10W-30 Oil tank capacity (cm ): ............................350 Carburetor: ............................Diaphragm type ignition system: ............................... Pointless Spark plug: ........................... -
Page 16: Limited Warranty
WHICH HAVE BEEN DAMAGED BY NEGLIGENCE OF THE PURCHASER SHALL BEAR COSTS OF TRANS- INSTRUCTION LISTED IN THE OWNER/OPERATOR PORTING THE UNIT TO AND FROM THE ZENOAH MANUAL FOR PROPER USE AND MAINTENANCE OF DEALER. THE UNITS ACCIDENT MISHANDLING, ALTERATION,...