Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Zenoah G3700
Summary of Contents for Zenoah G3700
- Page 1 CHAIN SAW G3700 848C6493A1 (704) OWNER’S MANUAL G3700 GB-1...
- Page 2 G3700 EXPLANATION OF SYMBOLS AND SAFETY WARNINGS Read operator's instruction book before operating this machine. Read, understand and follow all warnings. MODEL SOUND LEVEL EN 608 - ISO 7182 G3700 100.3 dB(A) APPROVAL NUMBER OF CE EXHAUST EMISSION REGULATION (2002/88/EC)
-
Page 3: Table Of Contents
: G3700 Serial no. : 600101 and up Make : ZENOAH CO., LTD. CONFORMS TO THE REQUIRMENTS OF THE MODIFIED MACHINES DIRECTIVE (Directive 98/37/EC) AND TO THE NATIONAL REGULATIONS GOVERNING ITS TRANSPOSITION ABROAD : AND THAT IT HAS BEEN ISSUED WITH A “CE”CERTIFICATE, NO. U3 2692468 01 BY TÜV Rheinland Group - TÜV Rheinland InterCert kft. -
Page 4: For Safe Operation
G3700 1. For safe operation 1. Never operate a chain saw when you are fatigued, ill, or upset, or under the influence of medication that may make you drowsy, or if you are under the influence of alcohol or drugs. - Page 5 • giving up or cutting down on smoking because smoking reduces blood flow; and massaging and exercising your fingers DISPOSAL When disposing your machine, fuel or oil for the ma- chine, be sure to allow your local regulations. G3700 GB-5...
-
Page 6: Explanation Of Symbols On The Machine
G3700 2. Explanation of Symbols on the Machine WARNING For safe operation and maintenance, symbols are carved in relief on the machine. According to these indications, please be careful not to make any mistake. The port to refuel “MIX GASOLINE”... -
Page 7: Installing Guide Bar And Saw Chain
A new chain will expand its length in the beginning of use. Check and readjust the tension frequently as a loose chain can easily derail or cause rapid wear of itself and the guide bar. Screwdriver for carburetor adjustment Lift up Loosen Tighten Tensioner screw G3700 GB-7... -
Page 8: Fuel And Chain Oil
3 m (10 ft) away from the fueling point before starting the engine. • The Zenoah engines are lubricated by oil specially for- mulated for air-cooled 2-cycle gasoline engine use. If Zenoah oil is not available, use an anti-oxidant added quality oil expressly labeled for air-cooled 2-cycle en- gine use (JASO FC GRADE OIL or ISO EGC GRADE). -
Page 9: Operating The Engine
Before adjusting the carburetor, make sure that provided are clean air/fuel filters and fresh, properly mixed fuel. When adjusting, take the following steps: NOTE Be sure to adjust the carburetor with the bar chain attached. G3700 Adjuster H needle Idle adjusting screw... - Page 10 NOTE When using the unit at times when it is snowing, Zenoah recommends that you also use a snow protector effec- tive in preventing the air filter from freezing (e.g., the separately-sold Z2850-98210 snow protector).
-
Page 11: Sawing
Before starting work, check the direction of bending force inside the log to be cut. Always finish cutting from the opposite side of the bending direction to prevent the guide bar from being caught in the cut. G3700 Felling cut GB-11... -
Page 12: Maintenance
G3700 A log lying on the ground Saw down halfway, then roll the log over and cut from the opposite side. A log hanging off the ground In area A, saw up from the bottom one-third and finish by sawing down from the top. In area B, saw down from the top one-third and finish by sawing up from the bot- tom. -
Page 13: Maintenance Of Saw Chain And Guide Bar
Keep the file position as illustrated. After each cutter has been filed, check the depth gauge and file it to the proper level as illustrated. Appropriate gauge checker .025 (0.65 mm) Depth gauge standard G3700 Champion RCJ-7Y Make the shoulder round GB-13... -
Page 14: Troubleshooting Guide
Such a bar needs to be corrected or replaced. Ruler No gap Chain tilts WARNING This saw is equipped with one of the following low kick- back bar/chain combinations: Zenoah Part Number Saw Model Bar Size Guide Bar G3700 848CB44C10 848CC95V60 (95VP) 848CB14020 3311-52210 (25AP) Case 3. -
Page 15: Specifications
30 days if used for rental purpose) from the date of initial purchase. THE PURCHASER SHALL BEAR COSTS OF TRANS- PORTING THE UNIT TO AND FROM THE ZENOAH DEALER. THE PURCHASER SHALL NOT BE CHARGED FOR DI- AGNOSTIC LABOR WHICH LEADS TO THE DETERMI-...