Table of Contents
Advertisement
5-3 Basic Operations with DTR+Panel and DTR+DTR
Modes
In DTR+Panel mode, the R1 and P1 ports are controlled
through the DTR-3000, while the other ports are
controlled through the control panel or an external device.
In DTR+DTR mode, R1/P1 and R2/P2 are each controlled
separately through two DTR-3000s.
5-3-1 Initial Setup for DTR+Panel
and DTR+DTR Modes
Before using the DTR+Panel and DTR+DTR modes,
confirm and set up the following:
(1) The DTR-3000 version connected to this unit must
be CP:V01.30, VS:V01.20 or later.
(2) The DTR-3000 must be set to the
DISK:INDIVIDUAL mode.
(3) The DTR-3000 recording time should be set on this
unit.
(4) Whether or not loop recording is used, it should be
set on this unit.
(5) Whether or not partial save is performed should be
set on this unit.
Please contact your supplier or Sony representative if you
require more details about (1) and (2) above.
For more details on (3) and (4) above, please refer to the
following operating information.
Setting the Recording Time from the DTR-
3000
1
Set DTR-1 (and DTR-2) in LIVE DURATION (menu
034) on the basic menu to the desired time.
2
Assuming it is okay to delete all material on this unit,
execute ALL ERASE (menu 099) on the basic menu,
and reboot the unit.
* If you don't want to delete all material, change this unit
to the Panel mode, delete the "LIVE1" (and "LIVE2")
material, the change back to the DTR+Panel (or
DTR+DTR) mode.
For basic menu operations, please see Section 3-4-2, "Basic Menu
Operation" (page 3-17).
Note
After changing the recording time (LIVE DURATION),
the materials must be deleted per Step 2 above. It is not
possible to extend the recording time and continue
recording from previously recorded material, or to
otherwise change the recording time in the midst of
recording.
For precautions and setup related to LIVE DURATION, please see
Section 3-4-1, "Basic Menu Settings" (page 3-12).
Loop Recording
During loop recording, when the recording time exceeds
the time set for LIVE DURATION, the oldest recorded
material is overwritten, so that even when the length of the
recording exceeds preset recording time, the most recent
recorded images are always stored up to the time set for
LIVE DURATION.
Loop recording is performed by the following procedure:
1
Set the LIVE DURATION (menu 034) on the basic
menu for DTR-1 (and DTR-2) to the desired time.
2
Set DTR-1 LOOP REC (or DTR-2 LOOP REC) on.
3
Assuming it is okay to delete all material on this unit,
execute ALL ERASE (menu 099) on the basic menu,
and reboot the unit.
* If you don't want to delete all material, change this unit
to the Panel mode, delete the "LIVE1" (and "LIVE2")
material, the change back to the DTR+Panel (or
DTR+DTR) mode.
For basic menu operations, please see Section 3-4-2, "Basic Menu
Operation" (page 3-17).
Note
Once material has been recorded, loop recording cannot be
turned on or off until the recorded material is erased.
5-3-2 Basic Operations in
DTR+Panel and DTR+DTR
Modes
After the initial settings described in the previous section,
the following operations can be performed.
Recording from the DTR-3000
1
While holding the SHIFT key, press the REC key on
the DTR-3000.
Recording starts at the recording port of this unit that
is connected to the operating DTR-3000.
2
To stop recording, hold the SHIFT key and press the
STOP key on the DTR-3000.
To resume recording, hold the SHIFT key while
pressing the REC key again.
5-3 Basic Operations with DTR+Panel and DTR+DTR Modes
5-3 (E)
Advertisement
Table of Contents
