Sony STR-DA2ES Service Manual page 2

STR-DA2ES/DB1080
Inputs (Digital)
DVD/LD (Coaxial) Impedance: 75 ohms
S/N: 100 dB
(A, 20 kHz LPF)
DVD/LD, TV/SAT,
S/N: 100 dB
MD/DAT, VIDEO3
(A, 20 kHz LPF)
(Optical)
Outputs
TAPE, MD/DAT Voltage: 150 mV
(REC OUT), VIDEO Impedance: 2.2 kilohms
1, 2 (AUDIO OUT)
FRONT L/R, Voltage: 2 V
Impedance: 1 kilohms
CENTER,
SURROUND L/R,
SURROUND BACK,
SUB WOOFER
EQ
BASS: 99 Hz~1.0 kHz
MID (FRONT L/R, CENTER only):
198 Hz~10 kHz
TREBLE: 1.0 kHz~10 kHz
Gain levels: ±10 dB, 0.5 dB step
FM tuner section
Tuning range
87.5 - 108.0 MHz
Antenna terminals 75 ohms, unbalanced
Sensitivity
Mono: 18.3 dBf, 2.2 µV/75 ohms
38.3 dBf, 22.5 µV/75 ohms
Stereo:
Usable sensitivity 11.2 dBf, 1 µV/75 ohms
S/N
Mono: 76 dB
Stereo: 70 dB
Harmonic distortion at 1 kHz
Mono: 0.3%
Stereo: 0.5%
Separation
45 dB at 1 kHz
Frequency response
30 Hz – 15 kHz,
+0.5/–2 dB
Selectivity 60 dB at 400 kHz
2
AM tuner section
Tuning range
Models of area code U, CA
With 10-kHz tuning scale: 530 – 1,710 kHz
With 9-kHz tuning scale: 531 – 1,710 kHz
Models of area code E
With 10-kHz tuning scale: 530 – 1,610 kHz
With 9-kHz tuning scale: 531 – 1,602 kHz
Models of area code SP, CEL, CEK, KR
With 9-kHz tuning scale: 531 – 1,602 kHz
Antenna
Loop antenna
Usable sensitivity
50 dB/m (at 1,000 kHz or
999 kHz)
S/N 54 dB (at 50 mV/m)
Harmonic distortion 0.5 % (50 mV/m,
400 Hz)
Selectivity
At 9 kHz: 35 dB
At 10 kHz: 40 dB
5) You can change the AM tuning scale to 9 kHz or
10 kHz. After tuning in any AM station, turn off
the receiver. Hold down TUNING + and press
?/1. All preset stations will be erased when you
change the tuning scale. To reset the scale to
10 kHz (or 9 kHz), repeat the procedure.
Video section
Inputs/Outputs
Video: 1 Vp-p, 75 ohms
S-video: Y: 1 Vp-p, 75 ohms
C: 0.286 Vp-p, 75 ohms
COMPONENT VIDEO
(Except for models of area code CEL, CEK):
Y: 1 Vp-p, 75 ohms
B-Y: 0.7 Vp-p, 75 ohms
R-Y: 0.7 Vp-p, 75 ohms
General
Power requirements
Area code Power requirements
U, CA 120 V AC, 60 Hz
CEL, CEK 230 V AC, 50/60 Hz
SP 220 – 230 V AC, 50/60 Hz
E 120/220/240 V AC, 50/60 Hz
KR 220 – 230 V AC, 60 Hz
Power consumption
Area code Power consumption
U 290 W
5)
5) CA 340 VA
CEL, CEK 300 W
5)
5) SP, E, KR 300 W
Power consumption (during standby mode)
0.8 W (when "POWER SAVE " in the CUSTOMIZE
menu is set to "OFF")/0.5 W ("ON")
AC outlets
Area code AC outlets
U, CA 2 switched, 120 W/1A MAX
SP, CEL, CEK 1 switched, 100 W MAX
E 2 switched, 100 W MAX
Dimensions
Mass (Approx.)
Supplied accessories
FM wire antenna (1)
AM loop antenna (1)
Models of area code U, CA;
Audio/video/control S cord (1)
Control S cord (mini jack) (1)
Remote commander RM-PG411 (1)
R6 (size-AA) batteries (2)
Models of other area codes;
Remote commander RM-LP211 (1)
R6 (size-AA) batteries (3)
Design and specifications are subject to change
without notice.
430 × 161 × 400 mm
including projecting parts
and controls
13.3 kg