Cabinet Disassembly Instructions - Philips 14PV360 Service Manual

CABINET DISASSEMBLY INSTRUCTIONS

1. Disassembly Flowchart
This flowchart indicates the disassembly steps for the
cabinet parts, and the CBA in order to gain access to
item(s) to be serviced. When reassembling, follow the
steps in reverse order. Bend, route and dress the
cables as they were.
Caution !!
When removing the CRT, be sure to discharge the
Anode Lead of the CRT with the CRT Ground Wire
before removing the Anode Cap.
[1] Rear Cabinet
[2] Tray Chassis Unit
[3] Top Shield
[4] Deck Unit
[5] Text CBA
[6] Main CBA
2. Disassembly Method
ID/
LOC. PART
Fig.
No.
No.
Rear
[1] 1, 2
Cabinet
Tray
[2] Chassis 3, 6
Unit
[3] Top Shield 3, 6 5(S-3)
[4] Deck Unit 3, 6
[5] Text CBA 3, 6 *CN751, *CN752
[6] Main CBA 3, 6 6(S-6)
4,5,
[7] Power Unit
6
[7] Power Unit
[8] H.V./Power
Supply CBA
REMOVAL
REMOVE/
*UNHOOK/
UNLOCK/RELEASE/
UNPLUG/DESOL-
DER
4(S-1), 2(S-2),
*CN801
*CN701,* CN702,
*CN503, *CN504,
*CN601, *CN602
7(S-4), 2(S-5),
Desolder *(CN201,
CL401, CL402,
CL403)
Anode Cap, *CN501,
CRT CBA, *CN571,
2(S-7)
ID/
LOC. PART
No.
H.V./Power
[8] Supply
CBA
[9] CRT
↓
(1)
(1): Order of steps in Procedure. When reassembling,
follow the steps in reverse order.These numbers
are also used as the identification (location) No. of
parts in Figures.
(2): Parts to be removed or installed.
(3): Fig. No. showing Procedure of Part Location.
(4): Identification of part to be removed, unhooked,
unlocked, released, unplugged, unclamped, or
desoldered.
S=Screw, P=Spring, L=Locking Tab, CN=Connec-
tor, *=Unhook, Unlock, Release, Unplug, or
Desolder
2(S-2) = two Screw (S-2)
(5): Refer to the following "Reference Notes in the
Table."
Note
Reference Notes in the Table
1. Removal of the Rear Cabinet.
1
Remove four screws (S-1) and two screws (S-2).
Then, disconnect connector CN801.
2. Removal of the Tray Chassis Unit.
2
Disconnect connectors CN701, CN702, CN503,
CN504, CN601 and CN602. Then pull the Tray
Chassis Unit out.
3
3. Removal of the Top Shield.
Remove five screws (S-3).
4
4. Removal of the Deck Unit.
Remove seven screws (S-4) and two screws (S-5).
Then,
5
CL402, CL403) and lift up the Deck Unit.
5. Removal of the Text CBA.
6
Disconnect connectors CN751 and CN752. Then,
lift the Text CBA up.
7
1-5-1
REMOVAL
REMOVE/
*UNHOOK/
Fig.
UNLOCK/RELEASE/
No.
UNPLUG/DESOL-
DER
4, 6 4(S-8)
5 4(S-9)
↓ ↓
(2) (3)
desolder connectors
Note
8
9
↓ ↓
(4) (5)
(CN201, CL401,
T6300DC