EnGenius EOC2611P Quick Start Manual page 2

EOC2611P
Wireless Access Point & Client Bridge
2. Name: Specify a user name into the first
field.
3. Password: Specify a password into this field
and then re-type the password into the
Confirm Password field. Then click on the
Apply button.
4. Click on the Apply button to save the
changes.
System Properties
1. Click on the System Properties link on the
System section. This feature allows you to
configure the device as an Access Point or
Repeater.
2. Device Name: Specify a name for the
device – this is not the SSID.
3. Country/Region: Select the region from the
drop-down list.
4. Operation Mode: Select Client Bridge,
Access Point, Client Router or WDS radio
button.
5. Click on the Apply button to save the
changes.
IP Settings
1. Click on the IP Settings link on the
System section. This feature allows you
to configure the LAN interface using a
static IP address or as a DHCP client.
This IP address is also used to access the
web-based interface.
2. IP Network Setting: Select Obtain an IP
address automatically (DHCP) radio
button if the Access Point is connected
to a DHCP server. This will allow the
Access Point to pass IP addresses to the
clients associated with it.
WARNING:
If device failed to obtain valid IP from a
DHCP
inaccessible. To access the device you
will have press reset button for 5
seconds to restore IP settings back to
192.168.1.1.
You may select Specify an IP Address
radio button if you would like the device
to use a static IP address. In this case,
you would be required to specify an IP
address, subnet mask, and default
gateway IP address.
3. IP Address: Specify an IP address
IP Subnet Mask: Specify the subnet
4.
mask for the IP address
Quick Start Guide v.1.0
Refer to User's Manual for complete instructions
4Gon www.4Gon.co.uk info@4gon.co.uk Tel: +44 (0)1245 808295 Fax: +44 (0)1245 808299
server, the device will be
Quick Start Guide
5. Default Gateway: Specify the IP address
of the default gateway.
6. Click on the Apply button to save the
changes.
Note: If you change the IP address here, you
may need to adjust your PC's network settings
to access the network again.
Wireless Network & Security
1. Click on the Wireless Network link on
the Wireless section. This feature allows
you to configure the wireless mode,
channel, SSID, and security settings.
2. Wireless Mode: Depending on the type
of wireless clients that are connected to
the network, you may select B, G, or
B/G-mixed.
3. Channel: Select a channel from the
drop-down list. The channels available
are based on the country's regulation.
4. You may configure up to four different
wireless profiles. Click on the Edit
button to modify the profile and place a
check in the Enable box to activate the
profile.
5. SSID: The SSID is a unique named shared
amongst all the points of the wireless
network. The SSID must be identical on
all points of the wireless network and
cannot exceed 32 characters.
6. VLAN ID: If you have enabled VLAN
tagging on your network, specify the
VLAN tag ID.
7. Suppressed SSID: Place a check in this
box if you would like to hide the SSID. By
enabling this feature, wireless clients
will not be able to scan this access point
in a site survey.
8. Station Separator: This is also known as
layer 2 isolation. Clients connected to
this Access Point will not be able to
directly communicate with each other.
9. Security Mode: By default, the security
is disabled. Refer to the user's Manual
to configure the security features such
as WEP, WPA,
WPA2-PSK and WPA-Mixed.
10. Click on the Apply button to save the
changes
WPA-PSK, WPA2,
2