Page 1 Before driving Introduction Instrumentation Controls and features Seating and safety restraints Starting and driving Starting Driving Roadside emergencies Servicing Maintenance and care Capacities and specifications Customer assistance Reporting safety defects Index All rights reserved. Reproduction by any means, electronic or mechanical including photocopying, recording or by any information storage and retrieval system or translation in whole or part is not permitted without written authorization from Ford Motor Company.
Page 2: Introduction
Introduction The following warning may be required by California law: CALIFORNIA Proposition 65 Warning Engine exhaust, some if its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer, or birth defects or other reproductive harm. ICONS Indicates a safety alert.
Page 3 Introduction WARNINGS Warnings provide information which may reduce the risk of personal injury and prevent possible damage to others, your vehicle and its equipment. BREAKING-IN YOUR VEHICLE There are no particular breaking-in rules for your vehicle. During the first 1 600 km (1 000 miles) of driving, vary speeds frequently. This is necessary to give the moving parts a chance to break in.
Page 4 Introduction These are some of the symbols you may see on your vehicle. Safety Alert Fasten Safety Belt Air Bag-Side Child Seat Installation Warning Brake System Brake Fluid - Non-Petroleum Based Master Lighting Switch Fog Lamps-Front Fuel Pump Reset Windshield Defrost/Demist Power Windows Front/Rear...
Page 5 Child Safety Door Lock/Unlock Panic Alarm Engine Coolant Do Not Open When Hot Avoid Smoking, Flames, or Sparks Explosive Gas Power Steering Fluid Emission System Passenger Compartment Air Filter Vehicle Symbol Glossary Interior Luggage Compartment Release Symbol Engine Oil Engine Coolant Temperature Battery Battery Acid...
Page 6: Instrumentation
Instrumentation Instrument panel Headlamp control (pg. 24) PANEL AUTO LAMP PUSH INTERIOR R.DEF. Rear window defroster control (pg. 25) Turn signal and wiper/washer control (pg. 60) * if equipped dimmer switch (pg. 24) Driver air bag (pg. 101) CHECK ENGINE VOLTS FUEL <...
Page 7 Gearshift with O/D control (pg. 125) COAST Climate control systems (pg. 26) VOL - PUSH ON BASS TREB FADE SEEK SIDE SCAN TUNE Clock (pg. 34) Instrumentation Electronic sound system (pg. 35) TAPE 1 - 2 Traction control switch* (pg. 120)
Page 8: Warning Lights And Chimes
Instrumentation WARNING LIGHTS AND CHIMES Standard instrument cluster TRAC CHECK FUEL ENGINE CNTL VOLTS FUEL < FUEL FILL DOOR Optional instrument cluster Low fuel (if equipped) Illuminates as an early reminder of a low fuel condition indicated on the fuel gauge (refer to Fuel gauge in this chapter for more information).
Page 9 Instrumentation Check engine Your vehicle is equipped with a computer that monitors the engine’s CHECK emission control system. This ENGINE system is commonly known as the On Board Diagnostics System (OBD II). This OBD II system protects the environment by ensuring that your vehicle continues to meet government emission standards.
Page 10 Instrumentation Light is blinking: Engine misfire is occurring which could damage your catalytic converter. You should drive in a moderate fashion (avoid heavy acceleration and deceleration) and have your vehicle serviced at the first available opportunity. Under engine misfire conditions, excessive exhaust temperatures could damage the catalytic converter, the fuel system, interior floor coverings or other vehicle components, possibly causing a fire.
Page 11 Brake system warning Standard instrument cluster Optional instrument cluster Momentarily illuminates when the ignition is turned to the ON position. Also illuminates if the parking brake is engaged. If brake warning lamp does not illuminate at these times, seek service immediately.
Page 12 Instrumentation Charging system Illuminates when the ignition is turned to the ON position and the engine is off. The light also illuminates when the battery is not charging properly, requiring electrical system service. Engine oil pressure (if equipped) Illuminates when the oil pressure falls below the normal range.
Page 13 O/D off Standard instrument cluster Optional instrument cluster Illuminates when the Transmission Control Switch (TCS), refer to Overdrive control in the Controls and Features chapter, has been pushed turning the transmission overdrive function OFF. When the light is on, the transmission does not operate in the overdrive mode, refer to the Driving chapter for transmission function and operation.
Page 14 Instrumentation Door ajar Illuminates when one of the doors is not completely shut and the ignition is turned to ON. With the ignition ON, this light will flash five times and sound a tone for one second, then remain on (if a door is open). Low washer fluid Momentarily illuminates when the ignition is turned to ON and will...
Page 15: Fuel Gauge
Headlamps on warning chime Sounds when the headlamps or parking lamps are on, the ignition is off (and the key is not in the ignition) and the driver’s door is opened. GAUGES Standard instrument cluster gauges TRAC CHECK CNTL FUEL ENGINE VOLTS FUEL...
Page 16 Instrumentation Standard instrument cluster Optional instrument cluster A minimum of four gallons must be added or removed from the fuel tank in order for the gauge to instantaneously update. If less than four gallons is added, the gauge will take between five to ten minutes to update.
Page 17 Optional instrument cluster Odometer Registers the total kilometers (miles) of the vehicle. Standard instrument cluster Optional instrument cluster Refer to Electronic Message Center for information on how to switch the display from metric to English measurements. Instrumentation 60 70 0 0 0 0 0 0 0 km/h km/h km/h...
Page 18 Instrumentation Trip odometer Registers the kilometers (miles) of individual journeys. To reset, depress the control. Refer to Electronic Message Center for Trip A and Trip B features on the optional instrument cluster. Engine coolant temperature gauge Indicates the temperature of the engine coolant. At normal operating temperature, the needle remains within the normal area (the area between the “H”...
Page 19 Optional instrument cluster This gauge indicates the temperature of the engine coolant, not the coolant level. If the coolant is not at its proper level the gauge indication will not be accurate. If the gauge enters the red section, the engine coolant and Check Engine/Service Engine Soon indicators illuminate, refer to What you should know about fail-safe cooling in the Maintenance and care chapter.
Page 20 Instrumentation Add oil if needed (refer to Engine oil in the Maintenance and care chapter). If the oil level is correct, have your vehicle checked at your dealership or by a qualified technician. ELECTRONIC MESSAGE CENTER The electronic message center only works when the ignition is in the ON position.
Page 21 Press this control to switch the electronic instrument cluster display and the message center display from metric to English units. Select Each press of the SELECT control will select a different function. Press the right side of the control to advance the function to the right, and press the left side of the control to advance the function to the left.
Page 22 Instrumentation Remember to turn the ignition OFF when refueling your vehicle. Otherwise, the display will not show the addition of fuel for a few miles. At least four gallons of fuel must be added for the fuel gauge to immediately show the new fuel level. The DTE function will flash for 5 seconds and sound a tone for 1 second when you have approximately: 80 km (50 miles) left before you run out of fuel...
Page 23 Press the RESET control while AVG ECON is displayed to reset the function. The average displayed is the average since the last reset. TRIP A and TRIP B These two functions allow you to see how far you have traveled since you last reset.
Page 24: Controls And Features
Controls and features PANEL DIMMER CONTROL Use to adjust the brightness of the instrument panel during headlight and parklamp operation. Push up to brighten. Push down to dim. HEADLAMP CONTROL Rotate the headlamp control to the first position to turn on the parking lamps.
Page 25 High beams Push forward to activate. Pull toward you to deactivate. Flash to pass Pull toward you to activate and release to deactivate. AUTOLAMP CONTROL (IF EQUIPPED) The autolamp system provides light sensitive automatic on-off control of the exterior lights normally controlled by the headlamp control.
Page 26 Controls and features Press the rear defroster control to clear the rear window of thin ice and fog. A small LED will illuminate when the rear defroster is activated. The ignition must be in the ON position to operate the rear window defroster.
Page 27 Since the air conditioner removes considerable moisture from the air during operation, it is normal if clear water drips on the ground under the air conditioner drain while the system is working and even after you have stopped the vehicle. MAX A/C-Uses recirculated air to cool the vehicle.
Page 28 Controls and features To prevent humidity buildup inside the vehicle, do not drive with the climate control system in the OFF or MAX A/C position. Do not put objects under the front seat that will interfere with the airflow to the back seats. Remove any snow, ice or leaves from the air intake area (at the bottom of the windshield).
Page 29 Turning the EATC on Press AUTOMATIC, any of the override controls or the fan speed control. The EATC will only operate when the vehicle is running. Turning the EATC off Press OFF. The Outside Temperature function will continue to operate until the ignition is turned off.
Page 30 Controls and features To control the temperature, select any temperature between 18°C (65°F) and 29°C (85°F) by pressing the blue (cooler) or red (warmer) buttons. For continuous maximum cooling, push the blue button until 16°C (60°F) is shown in the display window. The EATC will continue maximum cooling (disregarding the displayed temperature) until a warmer temperature is selected by pressing the red button.
Page 31 Fan speed ( When AUTOMATIC is pressed, fan speed is adjusted automatically for existing conditions. You can override fan speed at any time. To control fan speed manually, use the thumbwheel to cancel automatic fan speed operation. Rotate the thumbwheel up for higher fan speed or down for lower fan speed.
Page 32 Controls and features economical and will cool the inside of the vehicle faster. Airflow is from the instrument panel registers. This mode can also be used to prevent undesirable odors from entering the vehicle. NORM A/C-Uses outside air to cool the vehicle. The temperature display will remain the same and air will be cooled based on the selected temperature.
Page 33 Displaying outside temperature Press OUTSIDE TEMP to display the outside air temperature. It will be displayed until OUTSIDE TEMP is pressed again. If the selected temperature is changed while the outside temperature is displayed, the new temperature will be displayed for four seconds after it is changed, then the outside temperature will return to the window.
Page 34 Controls and features Remove any snow, ice or leaves from the air intake area (at the bottom of the windshield). If your vehicle has been parked with the windows closed during hot weather, the air conditioner will do a much faster job of cooling if you drive for two or three minutes with the windows open.
Page 35 USING YOUR AUDIO SYSTEM AM/FM stereo cassette VOL - PUSH ON BASS SEEK TUNE Volume/power control Press the control to turn the audio system on or off. Turn the control to raise or lower volume. If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal”...
Page 36 Controls and features AM/FM select The AM/FM select control works in radio and tape modes. AM/FM select in radio mode This control allows you to select AM or FM frequency bands. Press the AM control to select from AM selections, and press the FM control to select from FM1 or FM2 memory preset stations.
Page 37 Controls and features Scan function The scan function works in radio mode. SCAN Scan function in radio mode Press the SCAN control to hear a brief sampling of all listenable stations on the frequency band. Press the SCAN control again to stop the scan mode.
Page 38 Controls and features Treble adjust The treble adjust control allows you to increase or decrease the audio system’s treble output. Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers. Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers.
Page 39 Automatic Music Search The Automatic Music Search feature allows you to quickly locate the beginning of the tape selection being played or to skip to the next selection. To activate the feature, momentarily depress the TAPE AMS button. Then, press either REW (for the beginning of the current selection) or FF (to advance to the next selection).
Page 40 Controls and features Dolby noise reduction Dolby noise reduction operates only in tape mode. Dolby noise reduction reduces the amount of hiss and static during tape playback. Press the control to activate (and deactivate) Dolby noise reduction. Dolby noise reduction is manufactured under license from Dolby Laboratories Licensing Corporation.
Page 41 Volume/power control Press the control to turn the audio system on or off. Turn the control to raise or lower volume. If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on.
Page 42 Controls and features Tune adjust The tune control works in radio mode. Tune adjust in radio mode Press to move to the next frequency down the band (whether or not a listenable station is located there). Hold the control to move through the frequencies quickly. Press to move to the next frequency up the band (whether or not a listenable station is located there).
Page 43 Controls and features Scan function in radio mode Press the SCAN control to hear a brief sampling of all listenable stations on the frequency band. Press the SCAN control again to stop the scan mode. Scan function in CD or CD changer mode (if equipped) Press the SCAN control to hear a short sampling of all selections on the current CD.
Page 44 Controls and features Treble adjust The treble adjust control allows you to increase or decrease the audio system’s treble output. Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers. Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers.
Page 45 Rewind The rewind control works in CD mode. To rewind in CD mode, press the CD control (preset 1). Press the control again to deactivate rewind mode. Fast forward The fast forward control works in CD mode. To fast forward in CD changer mode, press the CD control (preset Press the control again to deactivate fast forward mode.
Page 46 Controls and features Premium AM/FM Stereo/Cassette (CD Changer Compatible) PUSH ON TAPE MUTE Your audio system is equipped with selective lighting, a unique lighting strategy. This lighting feature is operable when the headlamps are illuminated. During the operation of any selected mode, lighting for the individual function controls will either illuminate or turn off.
Page 47 Turn the control to raise or lower volume. If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on. AM/FM select The AM/FM select control works in radio, tape and CD modes (if...
Page 48 Controls and features disc unless the CD changer is in shuffle mode.) Refer to Shuffle feature for more information. Hold the control to continue reversing through the discs. Press to select the next disc in the CD changer. Hold the control to fast-forward through the remaining discs.
Page 49 Controls and features Scan function in radio mode Press the SCAN control to hear a brief sampling of all listenable stations on the frequency band. Press the SCAN control again to stop the scan mode. Scan function in tape mode Press the SCAN control to hear a short sampling of all selections on the tape.
Page 50 Controls and features Starting autoset memory preset 1. Select a frequency using the AM/FM select controls. 2. Press the AUTO control. 3. When the first six strong stations are filled, the station stored in memory preset control 1 will start playing.
Page 51 Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers. Press the FADE control. Use the SEL control to adjust the sound between the front and rear speakers. Tape/CD select To begin tape play (with a tape loaded into the audio system) while in the radio or CD mode, press the TAPE control.
Page 52 Controls and features In CD mode, pressing the control for less than three seconds results in slow forward action. Pressing the control for more than three seconds results in fast forward action. Tape direction select Press SIDE 1–2 to play the alternate side of a tape.
Page 53 shuffle feature continues to the next disc after all tracks are played. Press the SHUFFLE control to start this feature. Random order play will continue until the SHUFFLE control is pressed again. Mute mode Press the control to mute the playing media.
Page 54 Controls and features Program type Press the RDS control until the FIND program type is displayed. Use the SEL control to select the program type. With the feature on, use the SEEK or SCAN control to find the desired program type from the following selections: Classic Country...
Page 55 Setting the clock Your vehicle is equipped with a separate instrument panel mounted clock. Please refer to Clock in this chapter for instructions on setting the clock. CD changer (if equipped) The CD changer is located in one of the following locations: in the trunk in the center console under the driver’s seat...
Page 56 Controls and features 3. Turn the magazine (A) over. 4. Using the disc holder release knob (C), pull the disc holder (B) out of the magazine. If you pull too hard on the disc holder, the disc holder may come completely out of the magazine.
Page 57 Ensure that the disc holder is evenly inserted and at the same level as the magazine (A). The unit will not operate if the disc holder is not inserted at the same level (B). Radio power must be turned on to play the CDs in the changer. The magazine may be stored in the glove box when not being used.
Page 58 Controls and features Cleaning compact discs Inspect all discs for contamination before playing. If necessary, clean discs only with an approved CD cleaner and wipe from the center out to the edge. Do not use circular motion. CD and CD changer care Handle discs by their edges only.
Page 59 Radio reception factors Three factors can affect radio reception: Distance/strength. The further an FM signal travels, the weaker it is. The listenable range of the average FM station is approximately 40 km (24 miles). This range can be affected by “signal modulation.” Signal modulation is a process radio stations use to increase their strength/volume relative to other stations.
Page 60 Controls and features Cornering lamps When the turn signal is used and the headlamps are on, the cornering lamps will light either the right or left side depending on the direction of the turn. WINDSHIELD WIPER/WASHER CONTROLS Rotate the windshield wiper control to the desired interval, low or high speed position.
Page 61 TILT STEERING Pull the tilt steering control toward you to move the steering wheel up or down. Hold the control while adjusting the wheel to the desired position, then release the control. Never adjust the steering wheel when the vehicle is moving. OVERDRIVE CONTROL Activating overdrive (Overdrive) is the normal drive position for the best fuel economy.
Page 62 Controls and features The TCIL will no longer be illuminated. When you shut off and re-start your vehicle, the transmission will automatically return to normal For additional information about the gearshift lever and the transmission control switch operation refer to the Automatic Transmission Operation section of the Driving chapter.
Page 63 Once speed control is switched off, the previously programmed set speed will be erased. To set a speed Press SET/SET ACC/SET ACCEL. For speed control to operate, the speed control must be ON and the vehicle speed must be greater than 48 km/h (30 mph).
Page 64 Controls and features Accelerate with your accelerator pedal. When the desired vehicle speed is reached, press and release SET/SET ACC/SET ACCEL. You can accelerate with the accelerator pedal at any time during speed control usage. Releasing the accelerator pedal will return your vehicle to the previously programmed set speed.
Page 65 Pressing OFF will erase the previously programmed set speed. To return to a previously set speed Press RES/RSM/RESUME. For RES/RSM/RESUME to operate, the vehicle speed must be faster than 48 km/h (30 mph). Indicator light (if equipped) This light comes on when either the SET ACC/SET ACCEL or RES/RSM/ RESUME controls are pressed.
Page 66 Controls and features Do not use the HomeLink Universal Transceiver with any garage door opener that lacks safety stop and reverse features as required by U.S. federal safety standards (this includes any garage door opener model manufactured before April 1, 1982). A garage door which cannot detect an object, signaling the door to stop and reverse, does not meet current U.S.
Page 67 Canadian Programming During programming, your hand-held transmitter may automatically stop transmitting after two seconds which may not be long enough to program the HomeLink Universal Transceiver. To program your hand-held transmitters: continue to hold the button on the HomeLink Universal Transceiver.
Page 68 Controls and features After completing the “Programming” functions, follow these steps to train a garage door opener with the rolling code feature: 1. Locate the training button on the garage door motor head unit. Refer to the garage door opener manual or call 1–800–355–3515 or on the Internet at HomeLink.jci.com.
Page 69 Controls and features 2. When the indicator light begins to flash slowly (after 20 seconds), position the hand-held transmitter 5–14 cm (2 to 5 inches) away from the HomeLink surface. 3. Press and hold the hand-held transmitter button. 4. The HomeLink indicator light will flash, first slowly and then rapidly. When the indicator light begins to flash rapidly, release both buttons.
Page 70 Controls and features seconds, then display all segments until the magnetized item is removed. If a “C” is displayed, refer to Compass calibration adjustment. Most geographic areas (zones) have a magnetic north compass point that varies slightly from the northerly direction on maps. This variation is four degrees between adjacent zones and will become noticeable as the vehicle crosses multiple zones.
Page 71 Controls and features 5. The display will show all segments, then return to normal compass mode within ten seconds. Compass calibration adjustment Perform this adjustment in an open area free from steel structures and high voltage lines. 1. Start the vehicle. 2.
Page 72 Controls and features POWER WINDOWS Press and hold the rocker switches to open and close windows. Press the top portion of the rocker switch to close. Press the bottom portion of the rocker switch to open. Express down Press AUTO and release quickly. The window will open fully.
Page 73 Controls and features Window lock The window lock feature allows only the driver to operate the power windows. To lock out all the window controls WINDOW LOCK except for the driver’s press the left side of the control. Press the right side to restore the window controls. POWER DOOR LOCKS Press U to unlock all doors and L to lock all doors.
Page 74 Controls and features 2. Move the control in the direction you wish to tilt the mirror. 3. Return to the center position to lock mirrors in place. CHILDPROOF DOOR LOCKS When these locks are set, the rear doors cannot be opened from the inside.
Page 75 Controls and features REMOTE ENTRY SYSTEM (IF EQUIPPED) The remote entry system allows you to lock or unlock all vehicle doors without a key. The remote entry features only operate with the ignition in the OFF position. If there is any potential remote keyless entry problem with your vehicle, ensure ALL key fobs (remote entry transmitters) are brought to the dealership, to aid in troubleshooting.
Page 76 Controls and features You must complete steps 1-7 within 30 seconds or the procedure will have to be repeated. If the procedure needs to be repeated, you must wait 30 seconds. 1. Turn the ignition key to ON. 2. Press the power door unlock control on the door panel three times. 3.
Page 77 Controls and features Automatic door locks can be turned on/off with the keyless entry keypad through the following procedure: You must complete steps 1-5 within 30 seconds or the procedure will have to be repeated. If the procedure needs to be repeated, you must wait 30 seconds.
Page 78 Controls and features Opening the trunk Press the control once to open the trunk. Ensure that the trunk is closed and latched before driving your vehicle. Failure to latch the trunk may cause objects to fall out of the trunk or block the rear view.
Page 79 Illuminated entry The interior lamps illuminate when the remote entry system is used to unlock the door(s) or sound the personal alarm. The system automatically turns off after 25 seconds after the UNLOCK button on the remote transmitter is pressed or when the ignition is turned to the START or ACC position.
Page 80 Controls and features Replacing lost transmitters Take all your vehicle’s transmitters to your dealer if service is required. If you purchase additional transmitters (up to four may be programmed into memory), perform the following procedure: To reprogram the transmitters yourself, place the key in the ignition and turn from OFF to ON four times in rapid succession within 3 seconds.
Page 81 and devices cannot damage the PATS ignition key, but can cause a momentary concern if they are too close to the key during engine start. If a problem occurs, turn ignition OFF and restart the engine with all other objects on the key ring held away from the ignition key. Check to make sure the encoded ignition key is an approved Ford encoded ignition key.
Page 82 Controls and features You will need to have two previously programmed coded keys and the new unprogrammed SecuriLock implementation of each step in the procedure. Please read and understand the entire procedure before you begin. 1. Insert the first previously programmed coded key into the ignition and turn the ignition from OFF to ON (maintain ignition in ON for at least one second).
Page 83 See also Remote entry system in this chapter for more information. Your vehicle has a factory-set 5–digit code that operates the keyless entry system. You can also program your own 5–digit personal entry code. The factory-set code is located: on the owner’s wallet card in the glove compartment taped to the computer module When pressing the controls on the keyless entry keypad, press the middle of the controls to ensure a good activation.
Page 84 Controls and features Erasing personal code To erase all of the personal entry codes programmed to a vehicle: 1. Enter the factory-set code. 2. Press 1/2 within 5 seconds of step 3. Press and hold 1/2 for two seconds. All of the vehicle doors will lock and then unlock to confirm erasure.
Page 85 Controls and features Locking doors with the keyless entry system It is not necessary to enter the factory-set code prior to locking all doors. To lock the doors: Press 7/8 and 9/0 at the same time. 7 8 9 0 INTERIOR LUGGAGE COMPARTMENT RELEASE (IF EQUIPPED) Your vehicle is equipped with a mechanical interior luggage compartment release handle that provides a means of escape for children and adults in...
Page 86 Controls and features Keep vehicle doors and luggage compartment locked and keep keys out of a child’s reach. Unsupervised children could lock themselves in an open trunk and risk injury. Children should be taught not to play in vehicles. On hot days, the temperature in the trunk or vehicle interior can rise very quickly.
Page 87: Seating And Safety Restraints
SEATING Head restraints Your vehicle’s seats may be equipped with head restraints which are vertically adjustable. The purpose of these head restraints is to help limit head motion in the event of a rear collision. To properly adjust your head restraints, lift the head restraint so that it is located directly behind your head or as close to that position as possible.
Page 88 Seating and safety restraints Lift handle to move seat forward or backward. Pull lever up to adjust seatback. Using the manual recline function (if equipped) Never adjust the driver’s seat or seatback when the vehicle is moving. Do not pile cargo higher than the seatbacks to avoid injuring people in a collision or sudden stop.
Page 89 To adjust the front seatback using the manual recliner: Lift and hold the handle located on the side of the seat. Lean against the seatback to adjust it to your desired position. You can recline the seat back or bring it forward. Release the handle when the desired position has been reached.
Page 90 Seating and safety restraints Press to move the seat forward or backward. Press to move the front portion of the seat cushion up or down. Press to move the rear portion of the seat cushion up or down. Adjusting the power seats – seat mounted controls Never adjust the driver’s seat or seatback when the vehicle is moving.
Page 91 Reclining the seatback can reduce the effectiveness of the seat’s safety belt in the event of a collision. The power seat controls are located on the side of the driver’s seat. Press to raise or lower the seat, or to move the seat forward or backward.
Page 92 Seating and safety restraints All occupants of the vehicle, including the driver, should always properly wear their safety belts, even when an air bag SRS is provided. It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed.
Page 93 2. To unfasten, push the release button and remove the tongue from the buckle. The front and rear outboard safety restraints in the vehicle are combination lap and shoulder belts. The front passenger and rear seat outboard safety belts have two types of locking modes described below: Vehicle sensitive mode The vehicle sensitive mode is the normal retractor mode, allowing free shoulder belt length adjustment to your movements and locking in...
Page 94 Seating and safety restraints How to use the automatic locking mode Buckle the combination lap and shoulder belt. Grasp the shoulder portion and pull downward until the entire belt is extracted. Allow the belt to retract. As the belt retracts, you will hear a clicking sound.
Page 95 Front safety belt height adjustment Your vehicle has safety belt height adjustments for the driver and front passenger. Adjust the height of the shoulder belt so the belt rests across the middle of your shoulder. To lower the shoulder belt height, push the button and slide the height adjuster down.
Page 96 Seating and safety restraints Insert the tongue into the correct buckle (the buckle closest to the direction the tongue is coming from). To lengthen the belt, turn the tongue at a right angle to the belt and pull across your lap until it reaches the buckle.
Page 97 Conditions of operation If... The driver’s safety belt is not buckled before the ignition switch is turned to the ON position... The driver’s safety belt is buckled while the indicator light is illuminated and the warning chime is sounding... The driver’s safety belt is buckled before the ignition switch is turned to the ON position...
Page 98 Seating and safety restraints The following are reasons most often given for not wearing safety belts: (All statistics based on U.S. data) Reasons given... Consider... Crashes are rare 36 700 crashes occur every day. The more we events drive, the more we are exposed to rare events, even for good drivers.
Page 99 One time disable Anytime the safety belt is buckled and then unbuckled during an ignition ON cycle, Belt Minder will be disabled for that ignition cycle only. Deactivating/activating the belt minder feature Read steps 1 - 9 thoroughly before proceeding with the deactivation/activation programming procedure.
Page 100 Seating and safety restraints 6. Within seven seconds of the safety belt warning light turning off, buckle then unbuckle the safety belt. This will disable Belt Minder if it is currently enabled, or enable Belt Minder if it is currently disabled. 7.
Page 101 AIR BAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS) SUSP 60 70 CHECK ENGINE PANEL VOLTS FUEL AUTO LAMP km/h P R N D 2 1 < FUEL FILL DOOR PUSH INTERIOR R.DEF. Your vehicle is equipped with a crash sensing and diagnostic module which records information about the air bag and sensor systems.
Page 102 Do not attempt to service, repair, or modify the Air Bag Supplemental Restraint System or its fuses. See your Ford or Lincoln-Mercury dealer. Modifications to the front end of the vehicle, including frame, bumper, front end body structure and tow hooks may effect the performance of the air bag sensors increasing the risk of injury.
Page 103 Children and air bags For additional important safety information, read all information on safety restraints in this guide. Children must always be properly restrained. Accident statistics suggest that children are safer when properly restrained in the rear seating positions than in the front seating position.
Page 104 Seating and safety restraints The air bags inflate and deflate rapidly upon activation. After air bag deployment, it is normal to notice a smoke-like, powdery residue or smell the burnt propellant. This may consist of cornstarch, talcum powder (to lubricate the bag) or sodium compounds (e.g., baking soda) that result from the combustion process that inflates the...
Page 105 and the electrical wiring which connects the components. The diagnostic module monitors its own internal circuits and the supplemental air bag electrical system warning (including the impact sensors), the system wiring, the air bag system readiness light, the air bag back up power and the air bag ignitors. Determining if the system is operational The SRS uses a readiness light in the instrument cluster or a tone to indicate the condition of the system.
Page 106 Seating and safety restraints Important child restraint precautions You are required by law to use safety restraints for children in the U.S. and Canada. If small children ride in your vehicle (generally children who are four years old or younger and who weigh 18 kg [40 lbs] or less), you must put them in safety seats made especially for children.
Page 107 A belt-positioning booster should be used if the shoulder belt rests in front of the child’s face or neck, or if the lap belt does not fit snugly on both thighs, or if the thighs are too short to let the child sit all the way back on the seat cushion when the lower legs hang over the edge of the seat cushion.
Page 108 Seating and safety restraints Keep the buckle release button pointing up and away from the safety seat, with the tongue between the child seat and the release button, to prevent accidental unbuckling. Place seat back in upright position. Put the safety belt in the automatic locking mode. Refer to Automatic locking mode (passenger side front and outboard rear seating positions) (if equipped).
Page 109 Seating and safety restraints 2. Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together. 3. While holding the shoulder and lap belt portions together, route the tongue through the child seat according to the child seat manufacturer’s instructions.
Page 110 Seating and safety restraints 5. To put the retractor in the automatic locking mode, grasp the shoulder portion of the belt and pull downward until all of the belt is extracted and a click is heard. 6. Allow the belt to retract. The belt will click as it retracts to indicate it is in the automatic locking mode.
Page 111 Installing child safety seats in the lap belt seating positions 1. Lengthen the lap belt. To lengthen the belt, hold the tongue so that its bottom is perpendicular to the direction of webbing while sliding the tongue up the webbing. 2.
Page 112 Seating and safety restraints 1. Position the child safety seat on the passenger seat cushion. 2. Route the child safety seat tether strap over the back of the seat. For vehicles with adjustable head restraints, route the tether strap under the head restraint and between the head restraint posts, otherwise route the tether strap over the top of the seatback.
Page 113 PREPARING TO START YOUR VEHICLE Engine starting is controlled by the powertrain control system. This system meets all Canadian Interference-Causing Equipment standard requirements regulating the impulse electrical field strength of radio noise. When starting a fuel-injected engine, avoid pressing the accelerator before or during starting.
Page 114 Starting 2. Make sure the headlamps and vehicle accessories are off. 3. Make sure the parking brake is set. 4. Make sure the gearshift is in P (Park). 5. Turn the key to 4 (ON) without turning the key to 5 (START). If there is difficulty in turning the key, firmly rotate the steering wheel left and right until the key turns...
Page 115 Make sure the corresponding lights illuminate briefly. If a light fails to illuminate, have the vehicle serviced. If the driver’s safety belt is fastened, the STARTING THE ENGINE 1. Turn the key to 5 (START) without pressing the accelerator pedal and release as soon as the engine starts.
Page 116 Starting Using the engine block heater (if equipped) An engine block heater warms the engine coolant, which improves starting, warms up the engine faster and allows the heater-defroster system to respond quickly. Use of an engine block heater is strongly recommended if you live in a region where temperatures reach -23°C (-10°F) or below.
Page 117 Starting Important ventilating information If the engine is idling while the vehicle is stopped in an open area for long periods of time, open the windows at least 2.5 cm (one inch). Adjust the heating or air conditioning (if equipped) to bring in fresh air. Improve vehicle ventilation by keeping all air inlet vents clear of snow, leaves and other debris.
Page 118: Driving
Driving BRAKES Your service brakes are self-adjusting. Refer to the scheduled maintenance guide for scheduled maintenance. Occasional brake noise is normal and often does not indicate a performance concern with the vehicle’s brake system. In normal operation, automotive brake systems may emit occasional or intermittent squeal or groan noises when the brakes are applied.
Page 119 ABS warning lamp warning lamp in the instrument cluster momentarily illuminates when the ignition is turned to the ON position. If the light does not illuminate momentarily at start up, remains on or continues to flash, the ABS needs to be serviced. With the ABS light on, the anti-lock brake system is disabled and normal braking is still effective unless the...
Page 120 Driving The BRAKE warning lamp in the instrument cluster illuminates and remains illuminated (when the ignition is turned ON) until the parking brake is fully released. Always set the parking brake fully and make sure the gearshift is latched in P (Park). Turn off the ignition whenever you leave your vehicle.
Page 121 The system operates by detecting and controlling wheel spin. The system borrows many of the electronic and mechanical elements already present in the anti-lock braking system (ABS). Wheel-speed sensors allow excess rear wheel spin to be detected by the Traction Control portion of the ABS computer.
Page 122 Driving The Traction Control key from OFF to ON until you deactivate the system using the traction control switch in the glove compartment. STEERING Your vehicle is equipped with power steering. Power steering uses energy from the engine to help steer the vehicle. To prevent damage to the power steering pump: Never hold the steering wheel to the extreme right or the extreme left for more than a few seconds when the engine is running.
Page 123 This system keeps the rear of your vehicle at a constant level by automatically adding air or releasing air from the springs. If you exceed the load limit, the rear air suspension may not operate. The air suspension shut-off switch is located on the left side of the trunk.
Page 124 Driving If your vehicle gets stuck in mud or snow it may be rocked out by shifting from forward and reverse gears, stopping between shifts, in a steady pattern. Press lightly on the accelerator in each gear. Do not rock the vehicle if the engine is not at normal operating temperature or damage to the transmission may occur.
Page 125 R (Reverse) With the gearshift lever in R (Reverse), the vehicle will move backward. Always come to a complete stop before shifting into and out of R (Reverse). N (Neutral) With the gearshift lever in N (Neutral), the vehicle can be started and is free to roll.
Page 126 Driving To return to Overdrive mode, press the transmission control switch. The O/D OFF indicator light will no longer be illuminated. Each time the vehicle is started, the transmission will automatically return to normal Overdrive mode. Every time the vehicle is shut off and restarted, you must press the transmission control switch to cancel overdrive operation if the Overdrive mode is not desired.
Page 127 VEHICLE LOADING Before loading a vehicle, familiarize yourself with the following terms: Base Curb Weight: Weight of the vehicle including any standard equipment, fluids, lubricants, etc. It does not include passengers or aftermarket equipment. Payload: Combined maximum allowable weight of cargo, passengers and optional equipment.
Page 128 Driving Do not exceed the GVWR or the GAWR specified on the certification label. Do not use replacement tires with lower load carrying capacities than the originals because they may lower the vehicle’s GVWR and GAWR limitations. Replacement tires with a higher limit than the originals do not increase the GVWR and GAWR limitations.
Page 129 Towing trailers beyond the maximum recommended gross trailer weight could result in engine damage, transmission/axle damage, structural damage, loss of control, and personal injury. Preparing to tow Use the proper equipment for towing a trailer, and make sure it is properly attached to your vehicle.
Page 130 Driving Driving while you tow When towing a trailer: Ensure that you turn off your speed control. The speed control may shut off automatically when you are towing on long, steep grades. Consult your local motor vehicle speed regulations for towing a trailer. Use a lower gear when towing up or down steep hills.
Page 131 Do not allow waves to break higher than 15 cm (6 inches) above the bottom edge of the rear bumper. Exceeding these limits may allow water to enter critical vehicle components, adversely affecting driveability, emissions, reliability and causing internal transmission damage. Replace the rear axle lubricant anytime the axle has been submerged in water.
Page 132 Driving DRIVING THROUGH WATER Do not drive quickly through standing water, especially if the depth is unknown. Traction or brake capability may be limited and if the ignition system gets wet, your engine may stall. Water may also enter your engine’s air intake and severely damage your engine.
Page 133: Roadside Emergencies
In the United States, this card is found in the Owner Guide portfolio in the glove compartment in Ford vehicles and is mailed to you if you own a Mercury or Lincoln. In Canada, it is found in the Roadside Assistance book in the glove compartment.
Page 134 In the United States, you may purchase additional roadside assistance coverage beyond this period through the Ford Auto Club by contacting your Ford or Lincoln Mercury dealer. HAZARD FLASHER Use only in an emergency to warn traffic of vehicle breakdown, approaching danger, etc.
Page 135 Roadside emergencies The fuel pump shut-off switch is located on the left side of the trunk behind the trunk liner. Use the following procedure to reset the fuel pump shut-off switch. 1. Turn the ignition to the OFF position. 2. Check the fuel system for leaks. 3.
Page 136 Roadside emergencies Always replace a fuse with one that has the specified amperage rating. Using a fuse with a higher amperage rating can cause severe wire damage and could start a fire. Standard fuse amperage rating and color Fuse Mini Rating Fuses Grey...
Page 137 The fuses are coded as follows. Fuse/Relay Fuse Amp Location Rating — Roadside emergencies Passenger Compartment Fuse Panel Description Brake Pedal Position (BPP) Switch, Speed Control, Multi-Function Switch Wiper Control Module, Windshield Wiper Motor Not Used Lighting Control Module, Main Light Switch Backup Lamps, Variable Assist Power Steering (VAPS), Turn Signals, Air Suspension, Daytime Running Lamps,...
Page 138 Roadside emergencies Fuse/Relay Fuse Amp Location Rating 18A CB 20A CB Power distribution box The power distribution box is located in the engine compartment. The power distribution box contains high-current fuses that protect your vehicle’s main electrical systems from overloads. Always disconnect the battery before servicing high current fuses.
Page 139 The high-current fuses are coded as follows. Fuse/Relay Fuse Amp Location Rating 20A* 30A* 25A* — 15A* 20A* 20A CB 30A** 50A** 50A** 40A** Roadside emergencies Power Distribution Box Description Electric Fuel Pump Relay Generator, Starter Relay, Fuses 15 and 18 Radio, CD Changer, Subwoofer Amplifier Not Used Horn Relay...
Page 140 Roadside emergencies Fuse/Relay Fuse Amp Location Rating 30A** 50A** 40A** 50A** — 30A CB Relay 1 — Relay 2 — Relay 3 — Relay 4 — * Mini Fuses ** Maxi Fuses Relays Relays are located in the power distribution box and should be replaced by qualified technicians.
Page 141 When driving with the temporary spare tire do not: exceed 80 km/h (50 mph) under any circumstances load the vehicle beyond maximum vehicle load rating listed on the Safety Compliance Label tow a trailer use tire chains drive through an automatic car wash, because of the vehicle’s reduced ground clearance try to repair the temporary spare tire or remove it from its wheel use the wheel for any other type of vehicle...
Page 142 Roadside emergencies 5. Loosen each wheel lug nut one-half turn counterclockwise but do not remove them until the wheel is raised off the ground. Refer to Anti-theft lug nuts for information on removing anti-theft lug nuts. On vehicles equipped with Air Suspension, turn OFF the Air Suspension switch prior to jacking, hoisting or towing your...
Page 143 (not the dealer) to get a replacement key. If the lug wrench/lug nut key assembly is lost, see your nearest Ford or Lincoln/Mercury dealer who has access to the master set of keys. Do not use an impact wrench with the anti-theft key.
Page 144 Roadside emergencies To remove the anti-theft lug nut: 1. Insert the key over the locking lug nut. Make sure you hold the key square to the lug nut. If you hold the key at an angle, you could damage the key and the lug nut. 2.
Page 145 Roadside emergencies Do not attempt to push start your vehicle. Automatic transmissions do not have push-start capability. Preparing your vehicle 1. Use only a 12–volt supply to start your vehicle. 2. Do not disconnect the battery of the disabled vehicle as this could damage the vehicle’s electrical system.
Page 146 Roadside emergencies 2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery. 3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery. 4. Make the final connection of the negative (-) cable to an exposed metal part of the stalled vehicle’s engine, away from the battery and the carburetor/fuel injection system.
Page 147 Do not connect the end of the second cable to the negative (-) terminal of the battery to be jumped. A spark may cause an explosion of the gases that surround the battery. 5. Ensure that the cables are clear of fan blades, belts, moving parts of both engines, or any fuel delivery system parts.
Page 148 Roadside emergencies 2. Remove the jumper cable on the negative (-) connection of the booster vehicle’s battery. 3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’s battery. 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’s battery.
Page 149 Roadside emergencies After the disabled vehicle has been started and the jumper cables removed, allow it to idle for several minutes so the engine computer can relearn its idle conditions. WRECKER TOWING If you need to have your vehicle towed, contact a professional towing service or, if you are a member, your roadside assistance center.
Page 150: Maintenance And Care
Maintenance and care SERVICE RECOMMENDATIONS To help you service your vehicle: We highlight do-it-yourself items in the engine compartment for easy location. We provide a Scheduled Maintenance Guide which makes tracking routine service easy. If your vehicle requires professional service, your dealership can provide necessary parts and service.
Page 151 Working with the engine off 1. Set the parking brake and ensure the gearshift is securely latched in P (Park). 2. Turn off the engine and remove the key. 3. Block the wheels to prevent the vehicle from moving unexpectedly. Working with the engine on 1.
Page 152 Maintenance and care IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 4.6L SOHC V8 engine 1. Brake fluid reservoir 2. Engine oil dipstick 3. Engine oil filler cap 4. Windshield washer fluid reservoir 5. Air filter assembly 6. Power steering fluid reservoir 7.
Page 153 Maintenance and care ENGINE OIL Checking the engine oil Refer to the Scheduled Maintenance Guide for the appropriate intervals for checking the engine oil. 1. Make sure the vehicle is on level ground. 2. Turn the engine off and wait a few minutes for the oil to drain into the oil pan.
Page 154 Maintenance and care If the oil level is within this range, the oil level is acceptable. DO NOT ADD OIL. If the oil level is below this mark, engine oil must be added to raise the level within the normal operating range. If required, add engine oil to the engine.
Page 155 Maintenance and care engine oil filler cap and use a funnel to pour the engine oil into the opening. 3. Recheck the engine oil level. Make sure the oil level is not above the normal operating range on the engine oil level indicator (dipstick). 4.
Page 156 Maintenance and care BRAKE FLUID Checking and adding brake fluid Brake fluid should be checked and refilled as needed. Refer to the Scheduled Maintenance Guide for the service interval schedules. 1. Clean the reservoir cap before removal to prevent dirt or water from entering the reservoir.
Page 157 WINDSHIELD WASHER FLUID Checking and adding washer fluid Check the washer fluid whenever you stop for fuel. The reservoir is highlighted with a If the level is low, add enough fluid to fill the reservoir. In very cold weather, do not fill the reservoir all the way.
Page 158 Maintenance and care protection against rust and other forms of corrosion. an accurate temperature readout from the engine coolant gauge. The engine coolant must be maintained at the correct fluid level and concentration to work properly. If the engine coolant fluid level and concentration is not maintained correctly, damage to the engine and cooling system may result.
Page 159 DO NOT USE Ford Extended Life Engine Coolant F6AZ-19544-AA (orange in color). DO NOT USE a DEX-COOL engine coolant or an equivalent engine coolant that meets Ford specification WSS-M97B44-D. DO NOT USE alcohol or methanol antifreeze or any engine coolants mixed with alcohol or methanol antifreeze. DO NOT USE supplemental coolant additives in your vehicle.
Page 160 Maintenance and care Have your dealer check the engine cooling system for leaks if you have to add more than 1.0 liter (1.0 quart) of engine coolant per month. To avoid scalding hot steam or coolant from being released from the engine cooling system, never remove the radiator cap while the engine is running or hot.
Page 161 Severe climates If you drive in extremely cold climates (less than –36° C [–34° F]): it may be necessary to increase the coolant concentration above 50%. NEVER increase the coolant concentration above 60%. increased engine coolant concentrations above 60% will decrease the overheat protection characteristics of the engine coolant and may cause engine damage.
Page 162 Maintenance and care How fail-safe cooling works Standard cluster Optional cluster If the engine begins to overheat: the engine coolant temperature gauge will move to the H (hot) area (if your vehicle is equipped with analog gauges). the engine coolant temperature gauge will illuminate all eight bars and a tone will sound every five seconds for one minute (if your vehicle is equipped with digital gauges).
Page 163 Continued operation will increase the engine temperature: symbol will begin to flash. if your vehicle is equipped with digital gauges, the gauge bars will flash and a tone will sound every five seconds for one minute. the engine will completely shut down, causing steering and braking effort to increase.
Page 164 Maintenance and care CHECKING AND ADDING POWER STEERING FLUID Check the power steering fluid. Refer to the Scheduled Maintenance Guide for the service interval schedules. If adding fluid is necessary, use only MERCON ATF. 1. Start the engine and let it run until it reaches normal operating temperature (the engine coolant temperature gauge indicator will be near the center of the normal area between H and C).
Page 165 Maintenance and care Automatic transmission fluid expands when warmed. To obtain an accurate fluid check, drive the vehicle until it is at normal operating temperature (approximately 30 km [20 miles]). If your vehicle has been operated for an extended period at high speeds, in city traffic during hot weather or pulling a trailer, the vehicle should be turned off for about 30 minutes to allow fluid to cool before checking.
Page 166 Maintenance and care The transmission fluid should be in this range if at normal operating temperature (66°C-77°C [150°F-170°F]). The transmission fluid should be in this range if at ambient temperature (10°C-35°C [50°F-95°F]). High fluid level Fluid levels above the safe range may result in transmission failure.
Page 167 BATTERY Your vehicle is equipped with a Motorcraft maintenance-free battery which normally does not require additional water during its life of service. However, for severe usage or in high temperature climates, check the battery electrolyte level. Refer to the Scheduled Maintenance Guide for the service interval schedules.
Page 168 Maintenance and care When lifting a plastic-cased battery, excessive pressure on the end walls could cause acid to flow through the vent caps, resulting in personal injury and/or damage to the vehicle or battery. Lift the battery with a battery carrier or with your hands on opposite corners.
Page 169 Always dispose of automotive batteries in a responsible manner. Follow your local authorized standards for disposal. Call your local authorized recycling center to find out more about recycling automotive batteries. AIR FILTER MAINTENANCE Refer to the Scheduled Maintenance Guide for the appropriate intervals for changing the air filter element.
Page 170 Maintenance and care 6. Install a new air filter element. Be careful not to crimp the filter element edges between the air filter housing and cover. This could cause filter damage and allow unfiltered air to enter the engine if not properly seated.
Page 171 Maintenance and care To replace the wiper blades: 1. Pull the wiper arm away from the windshield and lock into the service position. 2. Turn the blade at an angle from the wiper arm. Push the lock pin manually to release the blade and pull the wiper blade down toward the windshield to remove it from the arm.
Page 172 Maintenance and care Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half (1 1/2) times as well on the government course as a tire graded 100.
Page 173 SERVICING YOUR TIRES Checking the tire pressure Use an accurate tire pressure gauge. Check the tire pressure when tires are cold, after the vehicle has been parked for at least one hour or has been driven less than 5 km (3 miles).
Page 174 Maintenance and care Five tire rotation (for vehicles with steel wheels and full size spare tires) Replacing the tires Replace the tires when the wear band is visible through the tire treads. When replacing full size tires, never mix radial bias-belted, or bias-type tires.
Page 175 Failure to follow these precautions may adversely affect the handling of the vehicle and make it easier for the driver to lose control and roll over. Tires that are larger or smaller than your vehicle’s original tires may also affect the accuracy of your speedometer. SNOW TIRES AND CHAINS Snow tires must be the same size and grade as the tires you currently have on your vehicle.
Page 176 Maintenance and care The fuel system may be under pressure. If the fuel filler cap is venting vapor or if you hear a hissing sound, wait until it stops before completely removing the fuel filler cap. Otherwise, fuel may spray out and injure you or others. If you do not use the proper fuel filler cap, excessive pressure or vacuum in the fuel tank may damage the fuel system or cause the fuel system to work improperly in a collision, which may result in...
Page 177 Avoid getting fuel liquid in your eyes. If fuel is splashed in the eyes, remove contact lenses (if worn), flush with water for 15 minutes and seek medical attention. Failure to seek proper medical attention could lead to permanent injury. Fuels can also be harmful if absorbed through the skin.
Page 178 Maintenance and care When fueling your vehicle: 1. Turn the engine off. 2. Carefully turn the filler cap counterclockwise 1/8 of a turn until it stops. 3. Pull to remove the cap from the fuel filler pipe. 4. To install the cap, align the tabs on the cap with the notches on the filler pipe.
Page 179 Maintenance and care Octane recommendations Your vehicle is designed to use “Regular” unleaded gasoline with an (R+M)/2 octane rating of 87. We do not recommend the use of gasolines (R+M)/2 METHOD labeled as “Regular” that are sold with octane ratings of 86 or lower in high altitude areas. Do not be concerned if your engine sometimes knocks lightly.
Page 180 Maintenance and care If you have run out of fuel: You may need to cycle the ignition from OFF to ON several times after refueling, to allow the fuel system to pump the fuel from the tank to the engine. Your “Check Engine”...
Page 181 For consistent results when filling the fuel tank: Use the same filling rate setting (low — medium — high) each time the tank is filled. Allow three automatic click-offs when filling. Always use fuel with the recommended octane rating. Use a known quality gasoline, preferably a national brand. Use the same side of the same pump and have the vehicle facing the same direction each time you fill up.
Page 182 Maintenance and care Habits Smooth, moderate operation can yield up to 10% savings in fuel. Steady speeds without stopping will usually give the best fuel economy. Idling for long periods of time (greater than one minute) may waste fuel. Anticipate stopping; slowing down may eliminate the need to stop. Sudden or hard accelerations may reduce fuel economy.
Page 183 Carrying unnecessary weight may reduce fuel economy (approximately 0.4 km/L [1 mpg] is lost for every 180 kg [400 lb] of weight carried). Adding certain accessories to your vehicle (for example bug deflectors, rollbars/light bars, running boards, ski/luggage racks) may reduce fuel economy.
Page 184 Maintenance and care The scheduled maintenance items listed in the Scheduled Maintenance Guide are essential to the life and performance of your vehicle and to its emissions system. If other than Ford, Motorcraft or Ford-authorized parts are used for maintenance replacements or for service of components affecting emission control, such non-Ford parts should be equivalent to genuine Ford Motor Company parts in performance and durability.
Page 185 If the vehicle’s powertrain system or its battery has just been serviced, the on-board diagnostics system is reset to a “not ready for I/M test” condition. To ready the on-board diagnostics system for I/M testing, a minimum of 30 minutes of city and highway driving is necessary as described below: First, at least 10 minutes of driving on an expressway or highway.
Page 186 Maintenance and care 3. Disconnect the electrical connector from the bulb by pulling rearward. 4. Remove the bulb retaining ring by rotating it counterclockwise (when viewed from the rear) to free it from the bulb socket, and slide the ring off the plastic base. Keep the ring to retain the new bulb.
Page 187 Maintenance and care 5. Turn the headlamps on and make sure they work properly. If the headlamp was correctly aligned before you changed the bulb, you should not need to align it again. Replacing front parking lamp/turn signal bulbs The park/turn lamp bulbs can be replaced with out removing the headlamp assembly.
Page 188 Maintenance and care 1. Open the trunk and carefully pull the carpet away to expose the plastic retainer. 2. Remove plastic retainer to expose the lamp assembly hardware. 3. Remove three nut and washer assemblies and the lamp assembly from the vehicle. 4.
Page 189 Replacing license plate lamp bulbs 1. Remove two screws, grommets and the license plate lamp assembly from the trunk lid. 2. Carefully pull the bulb from the socket and push in the new bulb. 3. Install the lamp assembly on trunk lid with two grommets, ensuring the grommets are pushed all the way in to the trunk lid and...
Page 190 Maintenance and care Function Headlamp Park lamp and turn lamp (front) Side marker (front) Cornering lamp (front) Tail, stop, turn (rear) Side marker (rear) Backup lamp License plate lamp High-mount brakelamp Luggage compartment lamp Dome lamp Rear reading lamp Map lamp Illuminated visor mirror Dual floorwell lamp Glove compartment...
Page 191 Maintenance and care Washing your vehicle Wash your vehicle regularly with cold or lukewarm water. Never use strong detergents or soap. If your vehicle is particularly dirty, use a quality car wash detergent. Always use a clean sponge, washing glove or similar device and plenty of water for best results.
Page 192 Maintenance and care Repairing paint chips Minor scratches or paint damage from road debris may be repaired with the Ultra Touch Prep and Finishing Kit (#F7AZ-19K507–BA), Lacquer Touch-up Paint (#ALBZ-19500–XXXXA), or Exterior Acrylic Spray Lacquer (#ALAZ-19500–XXXXA) from the Ford Car Care Chemicals line. Please note that the part numbers (shown as XXXX above) will vary with your vehicle’s specific coloring.
Page 193 To avoid scratching the lamps, do not use a dry paper towel, chemical solvents or abrasive cleaners. Cleaning the wiper blades, windshield and rear window If the wiper blades do not wipe properly, clean the wiper blade rubber element with undiluted windshield washer solution or a mild detergent. To avoid damaging the blades, do not use fuel, kerosene, paint thinner or other solvents.
Page 194 Maintenance and care Cover the highlighted areas to prevent water damage when cleaning the engine. Never wash or rinse the engine while it is running; water in the running engine may cause internal damage. Cleaning the instrument panel Clean with a damp cloth, then dry with a dry cloth. Avoid cleaner or polish that increases the gloss of the upper portion of the instrument panel.
Page 195 Cleaning seats equipped with side air bags Remove dust and loose dirt with a whisk broom or a vacuum cleaner. Remove fresh spots immediately. Follow the directions that come with the cleaner. Do not saturate the seat cover with upholstery cleaner. Do not use chemical solvents or strong detergents when cleaning the seat mounted side air bag.
Page 196 Maintenance and care Cleaning leather seats (if equipped) To clean, simply use a soft cloth dampened with water and a mild soap. Wipe the leather again with a damp cloth to remove soap residue. Dry with a soft cloth. For tougher soiling concerns, Ford recommends using the Deluxe Leather Care Kit F8AZ-19G253–AA, which is available from your Ford Dealer.
Page 197: Capacities And Specifications
MOTORCRAFT PART NUMBERS Component Air filter element Fuel filter Battery-standard Battery-heavy duty Oil filter PCV valve Spark plugs* * Refer to Vehicle Emissions Control Information (VECI) decal for spark plug gap information. REFILL CAPACITIES Fluid Engine oil (includes filter change) Brake fluid Power steering fluid Transmission fluid...
Page 198 Capacities and specifications MERCON V. Refer to the Scheduled Maintenance Guide to determine the correct service interval. Indicates only approximate dry-fill capacity. Some applications may vary based on cooler size and if equipped with an in-tank cooler. The amount of transmission fluid and fluid level should be set by the indication on the dipstick’s normal operating range.
Page 199 Item Ford part name Engine oil Motorcraft SAE 5W-30 Super Premium Motor Hinges, latches, Multi-Purpose striker plates, Grease fuel filler door hinge and seat tracks Lock cylinders Penetrating and Lock Lubricant Power steering Motorcraft fluid MERCON ATF Automatic Motorcraft transmission MERCON V (4R70W) Rear Axle...
Page 200 Capacities and specifications ENGINE DATA Engine Cubic inches Required fuel Firing order Spark plug gap Ignition system Compression ratio VEHICLE DIMENSIONS Vehicle dimensions (1) Overall length (2) Overall width (3) Overall height (4) Wheelbase (5) Track - Front (5) Track - Rear 4.6L V8 engine 87 octane 1-3-7-2-6-5-4-8...
Page 201 Capacities and specifications...
Page 202: Certification Label
Capacities and specifications IDENTIFYING YOUR VEHICLE Certification label The National Highway Traffic Safety Administration Regulations require that a Certification Label be affixed to a vehicle and prescribe where the Certification Label may be located. The Certification Label is located on the front door latch pillar on the driver’s side.
Page 203: Customer Assistance
You may purchase Ford ESP from any participating Ford and Lincoln/ Mercury and Ford of Canada dealer. There are several plans available in various time, distance and deductible combinations which can be tailored to fit your own driving needs. Ford ESP also offers reimbursement benefits for towing and rental coverage.
Page 204 Away from home If you own a Ford or Mercury vehicle and are away from home when your vehicle needs service, or if you need more help than the dealership could provide, after following the steps described above, contact the Ford Customer Assistance Center to find an authorized dealership to help you.
Page 205 Ford Motor Company of Canada, Limited P.O. Box 2000 Oakville, Ontario L6J 5E4 1-800-565-3673 (FORD) In order to help you service your Ford or Lincoln Mercury vehicle, please have the following information available when contacting a Customer Assistance Center: Your telephone number (home and business)
Page 206 Unresolved warranty repair concerns or vehicle performance as designed concerns on Ford and Lincoln Mercury cars and Ford and Lincoln Mercury light trucks which are within the terms of any applicable written new vehicle warranty are eligible for review, except those involving:...
Page 207 Ford or Lincoln Mercury dealership representative Consumer candidates for Board membership are recruited and trained by an independent consulting firm. The dealership Board member is chosen from Ford and Lincoln Mercury dealership management, recognized for their business leadership qualities. What the Board needs...
Page 208 Customer assistance the names (if known) of all the people you contacted at the dealership(s) a description of the action you expect to resolve your concern You will receive a letter of explanation if your application does not qualify for Board review. Oral presentations If you would like to make an oral presentation, indicate YES to question #6 on the application.
Page 209 Customer assistance You may also contact the North American Customer Assistance Center at 1-800-392-3673 (Ford), TDD for the hearing impaired: 1-800-232-5952 or by writing to the Center at the following address: Ford Motor Company Customer Assistance Center 16800 Executive Plaza Drive P.O.
Page 210 Customer assistance The use of leaded fuel in your vehicle without proper conversion may damage the effectiveness of your emission control system and may cause engine knocking or serious engine damage. Ford Motor Company/Ford of Canada is not responsible for any damage caused by use of improper fuel.
Page 211 FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of Ford accessories are available for your vehicle through your local authorized Ford, Lincoln Mercury or Ford of Canada dealer. These quality accessories have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and aerodynamic appearance of your vehicle.
Page 212 Customer assistance Comfort and convenience Cargo nets Cargo organizers Engine block heaters Travel equipment Daytime running lights Heavy-duty battery Protection and appearance equipment Air bag anti-theft locks Carpet floor mats Cleaners, waxes and polishes Flat splash guards Front end covers Lubricants and oils Molded splash guards Molded vinyl floor mats...
Page 213 Mobile communications systems may harm the operation of your vehicle, particularly if they are not properly designed for automotive use or are not properly installed. When operated, such systems may cause the engine to stumble or stall. In addition, such systems may be damaged or their performance may be affected by operating your vehicle.
Page 214: Reporting Safety Defects
Reporting safety defects REPORTING SAFETY DEFECTS (U.S. ONLY) If you believe that your vehicle has a defect that could cause a crash, or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Ford Motor Company.
Page 215: Index
Air bag supplemental restraint system ...101 and child safety seats ...103 description ...101 disposal ...105 driver air bag ...103 indicator light ...10,105 operation ...103 passenger air bag ...103 Air cleaner filter ...169,197 Air conditioning ...26 automatic temperature control system ...28 Air suspension ...122 description ...122 warning light ...12...
Page 216 Index set zone adjustment ...70 Controls power seat ...89,90 Coolant checking and adding ...157 coolant temperature light ...10 refill capacities ...160,197 specifications ...198,200 Cruise control (see Speed control) ...62 Customer Assistance ...133 Ford accessories for your vehicle ...210 Ford Extended Service Plan ...203 Getting assistance outside the U.S.
Page 217 quality ...179 running out of fuel ...179 safety information relating to automotive fuels ...175 Fuses ...135,136 Garage door opener ...65 Gas cap (see Fuel cap) ...177 Gas mileage (see Fuel economy) ...180 Gauges ...15 battery voltage gauge ...19 engine coolant temperature gauge ...18 engine oil pressure gauge ...19 fuel gauge ...15...
Page 218 Index anti-lock brakes (ABS) ...11,119 brake ...11 charging system ...12 check engine ...9 high beam ...11 low coolant ...10 low fuel ...8 oil pressure ...12 overdrive off ...13 safety belt ...10 speed control ...65 traction control active ...13 turn signal indicator ...11 Load limits ...127 GAWR ...127 GVWR ...127...
Page 219 Specification chart, lubricants ...198,200 Speed control ...62 Speedometer ...16 Starting your vehicle ...113,115 jump starting ...144 Steering speed sensitive ...122 Steering wheel tilting ...61 Tilt steering wheel ...61 Tires ...140,171,172,173 changing ...140,141 checking the pressure ...173 replacing ...174 rotating ...173 snow tires and chains ...175 tire grades ...172 treadwear ...172...
Page 224: Filling Station Information
Filling station information Required fuel Fuel tank capacity Engine oil capacity (includes filter change) Tire pressure and size Hood release Coolant capacity Automatic transmission fluid capacity Power steering fluid capacity Use Ford Premium Engine Coolant (green in color). DO NOT USE Ford Extended Life Engine Coolant (orange in color).

This manual is also suitable for:

2000 marquisGrand marquis 2000

Mercury 2000 Grand Marquis Owner's Manual

Quick Links

Related Manuals for Mercury 2000 Grand Marquis

Summary of Contents for Mercury 2000 Grand Marquis

This manual is also suitable for:

Table of Contents