NOTE: EU Standby Power Requirements are met operating and maintenance (servicing) instructions in the operating instructions or as marked on the appliance. when the MCA-C3 controller is configured with six literature accompanying the appliance. Grounding or Polarization - Precaution should be taken (6) MDK-C5 keypads attached.
Page 3
For complete guidelines on antenna grounding procedures, please consult the National Electrical Code, Section 810, ANSI/NFPA No. 70-1984. Antenna Lead-In Wire Grounding Conductors Ground Clamps Electric Service Equipment Power Service Grounding Electrode System Russound MCA-C3 User and Installation Manual...
Important Note: SCS-C5 Configuration software is necessary to program the easier than ever. MCA-C3 system. It can be downloaded from the Document Center at www. Key features include: russound.com.
Removable cover to access IR Red LED behind power indicator window and USB port behind cover Front Panel Red IR LED (talk-back) USB Port for Programming IR Receiver Window Front Panel with cover removed Russound MCA-C3 User and Installation Manual...
Page 7
2 (always Hot when set to Fixed) the zones power cord connection Page Audio In Fuse Holder Source 6 configurable as paging Holds replaceable fuse for audio input (right channel only) AC input connection Rear Panel Russound MCA-C3 User and Installation Manual...
OK - Press to select highlighted item from the menu, or access source list Menu Navigation - Navigate through from Now Playing menus, press (slow) or press and hold (fast) to move up/down a menu list MDK-C5 Keypad Functions Russound MCA-C3 User and Installation Manual...
Turn off active alarm - Press the power button on the keypad or SRC-C5 Now Playing remote control. Shared Sources Snooze - Press the pause button on the keypad or SRC-C5 remote control. Favorites Alarm Sleep Timer Russound MCA-C3 User and Installation Manual...
Page 10
Sleep Timer Diagnostics - The MDK-C5 provides firmware version information for Party Mode Controller 1 and the keypad. Network information such as Controller IP Do Not Disturb and MAC address are also provided. Settings Russound MCA-C3 User and Installation Manual...
Power - Turn the selected source on or off. Set - Program sequences Russound Zone Control - Activates control of Russound VID / DVD / TV - Use these keys to select a local device. system controller and keypads, and its connected sources.
LAN may be used to wake the system from standby. Installation Important Considerations The MCA-C3 controller can be rack mounted or placed on a shelf in an • Disconnect the power cord before making any connections to the equipment rack. The controller occupies two rack spaces with feet removed.
Standard 16-gauge 4-conductor stranded speaker wire can be run up to 125 feet; 14-gauge wire can be run up to 250 feet. Rack Ear Rack Ear Side View Side View Front View RJ45 CAT-5 Wiring Scheme RJ45 RJ45 Russound MCA-C3 User and Installation Manual...
IR receiver Programming Port OS Update Jumper Selects "Run" or Insert cable here for firmware updates. Requires "Program" mode Advanced Programming Cable P/N 2500-521065. MDK-C5 Keypad (rear) Russound MCA-C3 User and Installation Manual...
IR receiver. The MDK-C5 keypad has an External IR Receiver In terminal for connecting an external IR Receiver such as the Russound 858, SaphIR 862 Eye, or SaphIR 860 Phantom. Use two twisted pair wire with one pair connecting GND (GROUND) and IR (SIGNAL) and the other pair connecting ST (STATUS) and V+ (+12VDC).
Once the Display Lens is removed, put aside for reattachment later. Be careful to not damage the display. Screws HOME MENU Metal Frame Display Lens Bezel Molding Screws Frame Plate Trim Plate Keypad Disassembly / Assembly Russound MCA-C3 User and Installation Manual...
These RJ45 ports support MDK-C5 keypads and UNO-TS2 touchscreens . The six keypad ports correspond to the six zones supported by the MCA-C3. When a connected keypad is powered on, the zone becomes active and the corresponding zone LED lights up on the front of the MCA-C3 controller.
Strip 1 to 2 inches (2.5 to 5 cm) off the end of each speaker cable jacket. Then The MCA-C3 supports speaker outputs for all zones. These 20 watt per channel strip 1/4 inch (0.7 cm) of insulation off each wire. Twist the speaker wire strands stereo speaker level outputs have high-current two-channel analog amplifiers.
RNET Source Data Connections Source Audio Connections The RNET Link In and Link Out can be used to connect the MCA-C3 to other On the MCA-C3, sources 1 through 6 have standard stereo audio inputs. All specified Russound RNET-enabled source equipment. The connection is made source inputs have audio signal sensing.
IR CONNECTIONS IR Connections Common IR This output is supported by the MCA-C3 IR engine and supports IR pass- Routed IR Outputs through from any of the IR sources or zones. These allow control of any source These six routed IR emitter outputs are supported by the MCA-C3 IR engine equipment without that source being selected on the keypad.
Out of the first controller and into the Link In of the next controller. Along with If two or more MCA-C3 controllers are connected using the RNET Link In and RNET data signals, the RNET Link In and Link Out port passes source IR signals.
The trigger can be used to engage any 12VDC trigger device or component that does not exceed 100mA, such as the Russound R235LS amplifier. The connections for the trigger outputs are made using a two-conductor cable with 3.5mm male mini-plug ports at each end.
Page 23
- this will initiate the page. Polarity of 3.5mm Plug Paging Audio IN The MCA-C3 has a paging audio input on Source 6 (right channel only) that MCA-C3 Controller accepts line level audio signals via RCA cables. The paging inputs interface with the page output of a telephone system or other peripheral device.
Page 24
Home Theater Triggers These triggers are used to integrate with home theater systems that can provide a 12 volt trigger. The MCA-C3 can be used to power manage sources The 12VDC 100mA trigger out can be used to engage any 12VDC trigger that are being shared with the home theater system.
Page 25
12V trigger cable Home Theater Receiver MCA-C3 Controller Power strip Power cord Power cords ACT-1 120VAC outlet CD Player 12V trigger cable Tuner Loop to other 12VDC triggered device Sample Configuration - Home Theater Trigger Russound MCA-C3 User and Installation Manual...
AddITIONAL CONNECTIONS RS232 Serial Interface AM/FM Antenna Connections: The RS232 serial port is located on the back of the MCA-C3 and uses a DB-9 AM Antenna cable connection. The MCA-C3 supports serial communication with various Connect the included loop antenna for AM reception to the back panel, third-party automation systems through the RS232 port.
Sound Controls - Adjust Bass, Treble, Balance, and Loudness initial settings. available via download from the Doc Center at www.russound.com. With your PC laptop, you can configure the system prior to connecting with the MCA-C3 IR Keycode Learning - allows IR codes to be learned, saved, and managed.
The LED will not be lit if the keypad is not turned on or is absent. Check operation of all keypad functions. Check for functional IR signal pass-through (if applicable). 10. The system is now ready to use. Russound MCA-C3 User and Installation Manual...
Repeat step 4 for the remaining digits, using 2 for the second digit, and so on. Numeric Keypad - Enter IR codes and numeric input To check for other device codes, repeat steps 1-5, using the appropriate key. Remote Control Programming Keys Russound MCA-C3 User and Installation Manual...
Page 30
Enter 9-9-3 and then press VOL-. The LED blinks four times. Volume is independently Press the key (twice) containing the learned function to be deleted. The remote controlled for the selected devices. blinks twice. Russound MCA-C3 User and Installation Manual...
Rear- 1 Serial RS232, 19.2 kHz baud rate 1 Ethernet RJ45, 10/100 Base T 2 RJ45 RNET Links In/Out The MCA-C3 Controller meets EU Standby Power Requirements Frequency Range: AM 530 - 1710 kHz FM 87.7 - 107.9 MHz Antenna impedance AM: 300 Ohm balanced...
WARRANTY Warranty Before returning a unit for repair, call Russound at (603) 659-5170 for a Return Authorization number. Write this number on the shipping label and ship to: The Russound MCA-C3 Controller Amplifier and MDK-C5 Keypad are fully Russound guaranteed against all defects in materials and workmanship for two (2) years ATTN: Service from the date of purchase.
Page 39
NOTES Russound MCA-C3 User and Installation Manual...