Related Manuals for Newco LCD-2
Summary of Contents for Newco LCD-2
- Page 1 Installation Programming Guide PN: 120463 LCD-2: Ambient Liquid Coffee Dispenser...
- Page 2 This page left intentionally blank 27-November-13 Phone: 1.800.325.7867 Fax: 1.636.925.0029 www.newcocoffee.com...
-
Page 3: Installation Instructions
Place Machine on a Level Countertop Surface Connect ¼ Inch Flare water Supply to the Water Inlet located on lower Left Rear of the Machine. (NEWCO recommends copper tubing for use as water supply to all of our brewing equipment) Turn water Supply On Plug or wire brewer to the appropriate voltage circuit as indicated on the serial tag. - Page 4 REPAIR, REPLACEMENT OR REFUND. In no event shall NEWCO be liable for any other damage or loss, including, but not limited to, lost profits, lost sales, loss of use of equipment, claim’s of BUYER’S customers, cost of capital, cost of downtime, cost of...
- Page 5 Section 2 Set-Up Programming Instructions: Open machine cabinet door and locate the 3-switch control panel w/lighted display screen. Three dashed lines will appear on the display screen. As shown in figure 1. Fig. 1 Step 1. Enter a Programming Mode Fig.
- Page 6 Fig 3 Fig 4 Fig 5 Step 3. Enable/Disable Alarm This machine features a buzzer alarm that will sound to notify the operator when one of the following three things has occurred: • BIB Tracking has detected an empty BIB (See step 4) •...
- Page 7 Pump 2 is mounted on the right side of the mixing chamber. Pump 2 supports the product BIB that is installed directly above it. To program a selector switch to create a drink using the product on the left, enter the pump speed from Chart A below in to Pump 1 and set the speed of Pump 2 to :00 Program selection single product: To program a selector switch to create a drink using the product on the right, enter the pump speed...
- Page 8 Low Flow Rate Chart (Use this chart if the unit is a low flow unit.) Chart A Pump Speed Chart B Pump Speed Ratios Setting Settings (Single) (Blend) 45:1 40:1 35:1 30:1 25:1 20:1 15:1 The front nozzle determines the flow rate. The back nozzle is for hot water use only.
- Page 9 To Program a selector switch: 1. On the selector switch control Fig 8 Fig 9 panel, press the switch that you want to program. The display will change to identify the switch that you have chosen. (b01 thru b06 are the switch identifiers.) See figures 8 &...
- Page 10 6. Press “Enter” to save and proceed with the set-up program. A time value (min: sec) will appear in the display. If the switch that Fig 13 you are programming has been set in a portion control mode, the value will represent the current dispense time for the switch. If the switch is in a continuous flow (push and hold) mode, the time value will be 0:00 Shown in figure 13.
- Page 11 4. Press and release the settings “Enter” 3 times. (The selector switch timer will appear on the display.) 5. Using the + and – switches, scroll until the selector switch timer reads 0:00 6. Press and release the “Enter” switch until 3 dashed lines appears on the display. 7.
- Page 12 Disconnect the BIB of sanitizing solution from the Pump 1 BIB connector and connect it to the Pump 2 connector. Press the “Pump 2 (–) switch on the display panel to begin sanitizing. When sanitizing cycle ends, remove the sanitizing solution and replace the products. The machine will automatically advance to the Prime Pumps mode.
- Page 13 Remove the plastic insert from the BIB fitment as shown in figure Fig. 2 Using finger and thumb only to prevent over- tightening, thread the BIB connector on to the BIB fitment until seated as shown in figure 3. Fig. 3 Place the product in the storage compartment as shown in figure 4.
-
Page 14: Cleaning And Sanitizing Instructions
Position the tubing as shown in figure 5. Fig. 5 Cleaning & Sanitizing Instructions: Remove product from storage area and disconnect BIB connectors as shown in figures 1 & 2. Fig. 1 Fig. 2 Place an empty container in the dispense area of the machine as shown in figure 3. - Page 15 Connect the sanitizing solution to the BIB connector for Pump 1 (the connector on the left as you face the machine from the front) and place sanitizing BIB on the product shelf as shown in figures 4 & 5. Fig. 4 Fig.
- Page 16 Fig. 8 Fig. 7 Disconnect sanitizing solution from Pump 1 and connect to the BIB connector for PUMP 2 as shown figures 7 & 8. Press Pump 2 button to begin sanitizing Pump as shown in figure 9. Fig. 9 When cycle is finished remove sanitizing solution and reinstall products as shown in figure 10.
- Page 17 Press and hold Pump 1 button until product flows from dispense head to prime pump 1 as shown in figure 11. Fig. 11 Press enter to proceed to Pump 2 as shown in figure 12. Fig. 12 Press and hold Pump 2 button until product flows from dispense head to prime Pump 2 as shown in figure 13.
- Page 18 Flushing Instructions: Flush the mixing chamber by pressing and holding the “Enter” button for 5 seconds until “FLU” appears on the display. Release the “Enter” button. Press and hold either the + or – button to flush the mixing chamber with water. (Refer to: Page 3 Section 2 Figure No. 2.) Flush Product &...
-
Page 19: Error Messages
Error Messages: Error Description Cause What to Check Number tHU/ tHL Thermistor warning – immediately upon Resistance extremely high from upper or This warns you that 1 thermistor has detection the machine will beep twice and lower thermistor will cause or the resistance failed. - Page 20 Error Messages Cont’d: Bad (Open) Motor Driver - The motor errors Bad/open motor driver. Pump 0 or pump 1. Retry pump if the error still occurs then (Er7 and Er8) do not cause a system error replace main board. and will not shut down the machine. Immediately upon detection the machine will beep twice and show the error message.
- Page 21 Dimensions & Electrical Specifications: LCD-2 LIQUID COFFEE DISPENSER **Electrical Specs** PN: 120463: LCD-2 Ambient 120V 20 Watts .2 Amps 27-November-13 Phone: 1.800.325.7867 Fax: 1.636.925.0029 www.newcocoffee.com...
-
Page 22: Electrical Schematics
Electrical Schematics: 27-November-13 Phone: 1.800.325.7867 Fax: 1.636.925.0029 www.newcocoffee.com... - Page 23 This page left intentionally blank 27-November-13 Phone: 1.800.325.7867 Fax: 1.636.925.0029 www.newcocoffee.com...
- Page 24 This page left intentionally blank 27-November-13 Phone: 1.800.325.7867 Fax: 1.636.925.0029 www.newcocoffee.com...