Related Manuals for Kenwood KDC-153
Summary of Contents for Kenwood KDC-153
-
Page 1: Instruction Manual
KDC-153 CD-RECEIVER INSTRUCTION MANUAL © 2011 Kenwood Corporation All Rights Reserved. GET0741-001A (MW/M0) -
Page 2: Table Of Contents
If you experience problems during components installation, consult your Kenwood dealer. When you purchase external components, Function settings check with your Kenwood dealer to make sure that they work with your model and in Troubleshooting your area. Installation/connection The marking of products using lasers... -
Page 3: Preparation
Preparation How to attach/detach the faceplate How to reset your unit If this unit fails to operate properly, press the reset button. The unit returns to factory settings when the reset button is pressed. Do not expose the faceplate to direct Reset button sunlight, excessive heat, or humidity. -
Page 4: Basic Operations
Basic operations Loading slot Ejects the disc Detaches the faceplate Display window Volume knob Auxiliary input jack When you press or hold the following button(s)... Button General operation Turns on. Turns off if pressed and held. Selects the available sources (TUNER, CD, AUX, STANDBY), if the power is turned on. -
Page 5: Getting Started
Getting started Canceling the display Adjusting the clock demonstration 1 Press the volume knob to enter [FUNCTION] mode. The display demonstration is always turned 2 Turn the volume knob to select on unless you cancel it. [SETTINGS], then press to enter. When you turn on the power (or after you 3 Turn the volume knob to select [CLOCK], reset the unit), the display shows:... -
Page 6: Listening To The Radio
Item Selectable setting (Preset: *) SWITCH PRE REAR */ SUB-W: Selects whether rear speakers or a subwoofer are connected to the line out terminals on the rear of the unit (through an external amplifier). SP SELECT OFF */ 5/4/ 6 × 9/6/ OEM: Selects the speaker size for optimum performance. Listening to the radio Hold for about 2 seconds to memorize the current station. -
Page 7: Listening To A Disc
Item Selectable setting (Preset: *) LOCAL SEEK ON: Searches only MW/ SW1/ SW2 stations with good reception. ; OFF *: Cancels. Selects the tuning mode for 4 / ¢ buttons. SEEK MODE AUTO1 *: Automatically search for a station. ; AUTO2: Search in the order of the stations in the preset memory. -
Page 8: Selecting A Track
Selecting a track Discs that cannot be used 1 Press to enter Music Search mode. Discs that are not round. “SEARCH” appears, then the current track Discs with coloring on the recording name appears on the display. surface or discs that are dirty. 2 Turn the volume knob to select a track, You cannot play a Recordable/ReWritable then press to confirm. -
Page 9: Function Settings
Function settings 1 Press the volume knob to enter [FUNCTION] mode. 2 Turn the volume knob to select [AUDIO CTRL] or [SETTINGS], then press to enter. 3 Turn the volume knob to make a selection, then press to confirm. See table below for selection. Repeat step 3 until the desired item is selected/activated. -
Page 10: Troubleshooting
[SETTINGS] Item Selectable setting (Preset: *) AUX NAME AUX */ DVD/ PORTABLE/ GAME/ VIDEO/ TV: Selects the desired name for the connected component. (Selectable only if “AUX” is selected as the source.) CLOCK CLOCK ADJ: (For details, refer page 5.) DISPLAY DIMMER SET: ON: Dims the display illumination. -
Page 11: Installation/Connection
For safety's sake, leave Be sure to ground this unit to the car's this work to professionals. chassis again after installation. If you experience problems during installation, consult your Kenwood dealer. -
Page 12: Wiring Connection
To the power control terminal of the optional power amplifier (Power control wire) To the terminal that is grounded when either the telephone rings Brown or during conversation. (To connect the Kenwood navigation (Mute control wire) system, consult your navigation manual.) Car fuse box... -
Page 13: Specifications
Installing without using the Removing the unit mounting sleeve (Japanese car) 1 Detach the faceplate. 2 Engage the catch pin on the removal 1 Remove the mounting sleeve and escutcheon from the unit. tools into the holes on both sides of the escutcheon, then pull it out. - Page 14 This symbol mark indicates that Kenwood manufactured this product so as to decrease harmful influence on the environment.