Makita LS0714N Instruction Manual page 12

Stopper arm
Fig.11
The lower limit position of the blade can be easily
adjusted with the stopper arm. To adjust it, move the
stopper arm in the direction of the arrow as shown in the
figure. Adjust the adjusting screw so that the blade stops
at the desired position when lowering the handle fully.
Sub-fence (for European countries only)
Fig.12
This tool is equipped with the sub-fence. Usually position
the sub-fence inside. However, when performing left
bevel cuts, flip it outward.
CAUTION:
When performing left bevel cuts, flip the sub-fence
•
outward. Otherwise, it will contact the blade or a
part of the tool, causing possible serious injury to
the operator.
Adjusting the miter angle
Fig.13
Loosen the grip by turning counterclockwise. Turn the
turn base while pressing down the lock lever. When you
have moved the grip to the position where the pointer
points to the desired angle on the miter scale, securely
tighten the grip clockwise.
CAUTION:
When turning the turn base, be sure to raise the
•
handle fully.
After changing the miter angle, always secure the
•
turn base by tightening the grip firmly.
Adjusting the bevel angle
Fig.14
Fig.15
To adjust the bevel angle, loosen the lever at the rear of
the tool counterclockwise.
Push the handle to the left to tilt the saw blade until the
pointer points to the desired angle on the bevel scale.
Then tighten the lever clockwise firmly to secure the
arm.
To tilt the blade to the right, push the release button at the
rear of the tool while tilting the blade slightly to the left
after loosening the lever. With the release button
depressed, tilt the saw blade to the right.
CAUTION:
When tilting the saw blade, be sure to raise the
•
handle fully.
After changing the bevel angle, always secure the
•
arm by tightening the lever clockwise.
When changing bevel angles, be sure to position
•
the kerf boards appropriately as explained in the
"Positioning kerf boards" section.
Adjusting the lever position
Fig.16
The lever can be repositioned at every angle 30° when
the lever does not provide full tightening.
Loosen and remove the screw that secures the lever at
the rear of the tool. Remove the lever and install it again
so that it is slightly above the level. Secure the lever with
the screw firmly.
Switch action
CAUTION:
Before plugging in the tool, always check to see
•
that the switch trigger actuates properly and returns
to the "OFF" position when released.
When not using the tool, remove the lock-off button
•
and store it in a secure place. This prevents
unauthorized operation.
Do not pull the switch trigger hard without pressing
•
in the lock-off button. This can cause switch
breakage.
For European countries
Fig.17
To prevent the switch trigger from being accidentally
pulled, a lock-off button is provided. To start the tool,
push the lever to the left, press in the lock-off button and
then pull the switch trigger. Release the switch trigger to
stop.
For all countries other than European countries
Fig.18
To prevent the switch trigger from being accidentally
pulled, a lock-off button is provided. To start the tool,
press in the lock-off button and pull the switch trigger.
Release the switch trigger to stop.
WARNING:
NEVER use tool without a fully operative switch
•
trigger. Any tool with an inoperative switch is
HIGHLY DANGEROUS and must be repaired
before further usage.
For your safety, this tool is equipped with a lock-off
•
button which prevents the tool from unintended
starting. NEVER use the tool if it runs when you
simply pull the switch trigger without pressing the
lock-off button. Return tool to a Makita service
center for proper repairs BEFORE further usage.
NEVER tape down or defeat purpose and function
•
of lock-off button.
Lighting up the lamps
For model LS0714F, LS0714FL
Fig.19
CAUTION:
This is not a rainproof light. Do not wash the light in
•
water or use it in a rain or a wet area. Such a
conduct can cause an electric shock and fume.
12