GE 4PE21A1 Instructions Manual page 104

CABINET UNITS
EBI-3163C
MONITOR
CABINET
BASE,
MODEL 4PR12A1
The Monitor Cabinet Base
is
a floor -mounted unit
used with top cabinets, Models 4PR13A1, 4PR14A1
or 4PR15A1. The desk
is
linoleum covered and has
an opening for mounting control panels. Both the
front and rear have ventilation
grilles and air
-filter
mounting brackets. Cable ports are located
on
both
sides
and rear. Buttons are available to
close
the
ports not
used. The bottom
is
also open to receive
interconnection
wiring. On either
side are four
-inch holes through
which several cabinets can be
connected or End Caps attached. In the bottom are
four
5/
-inch diameter mounting holes. The front
panel and an
access panel beneath the desk are both
readily removable. In the center are brackets and
rubber shock mounts on which
is
located
a
ventilating
fan. Spring pull tapes are mounted
on
either
side.
These hook to the back end
of a
monitor and unwind
as
the monitor
is
lowered into position.
DUAL
MONITOR TOP
CABINET, MODEL 4PR13A1
The Monitor Top Cabinet
is a
top cabinet unit
containing the
slides and
guides for housing
a
Dual
Monitor
or Calibration Monitor.
A
ventilation
grille
is
located
in
the top. The unit
is
designed to
be
mounted
on a
Monitor Cabinet
Base or on
a
Monitor
Cabinet
Spacer.
SINGLE
MONITOR
CABINET, MODEL 4PR14A1
The
Single
Monitor Cabinet
is
a
top cabinet unit
containing the
slides and
guides for housing a Picture
Monitor.
A
ventilation
grille
is in
the top. The unit
is
designed to be mounted on a Monitor Cabinet
Base.
MONITOR
CABINET SPACER, MODEL 4PR15A1
The Monitor Cabinet Spacer
is an open
rectangular
unit
designed to
be
located between
a
Monitor
Base
Cabinet and
a Dual Monitor Cabinet. It
increases
the height
of
the Dual Monitor Cabinet by approxi-
mately
7
inches. The front contains
a
removable
panel which can be replaced with a desk type control
panel. Extra
space
is
covered by a spacer panel.
BASE
CABINET, MODEL 4PR16A1
The
Base
Cabinet
is
a
flat-topped
floor
-mounted
unit
used with Top Cabinet, Model 4PR17A1. The
top
is
partially
covered with matte black linoleum.
Openings are available
in
the uncovered part
for
interconnection
wiring.
Front and rear panels
are
removable. The rear panel contains ventilation grilles.
Inside are angles for mounting
standard
-size
rack
chassis up to
24
inches in height. Cable
ports
are
located on both
sides and rear. The
side
ports
line
up with those in
the
4PR12A1 base. Buttons
are
available to
close the ports not
used. The bottom
is
also open to receive interconnection
wiring. On
either
side
are %-inch holes through which several
cabinets can
be
connected or End Cops attached.
In the bottom corners are four %-inch diameter
mounting
holes.
BASE CABINET,
MODEL 4PR16B1
The 4PR16B1
Base Cabinet
is
similar to 4PR16A1
except
that
it has desk mounting space for two
51A -
inch by
15k
-inch
6
-inch
studio control panels. If only
one
control panel
is
used, a blank panel
is available to
cover the remaining space. The entire surface, except
panel area,
is
covered with matte
black linoleum. In
case an
11
-inch panel
is
used,
the center supporting
angle for the 5%
-inch panel may be readily removed
by taking out the
screws.
BASE CABINET, MODEL 4PR16C1
Base Cabinet 4PR16C1
is
similar to 4PR16A1
except it has
no
top openings, the entire surface
being covered with matte
black linoleum.
TOP CABINET, MODELS 4PR17A1, 4PR17A2, 4PR17A3
The Top Cabinet
is
a
desk -mounted
unit
with a
hinged front bracket for mounting audio and master
control
panels. The
unit mounts
on
the Base Cabinet
4PR16A1 and
is
secured through four mounting holes
which
mate those
in the Base Cabinet. The Top
Cabinet base
is
open
permitting
easy access of inter-
connection wiring.
Model 4PR17A2
is
identical with Model 4PR17A1
except
that
it
is
constructed to take
a frame with
a
piano hinge instead
of being equipped with
a
throw
-
out hinge.
Cabinet 4PR17A3
is
supplied with throw -out type
hinges, with additional provision
for mounting panels
with
a
piano hinge. This
unit may
be used in place
of
either the
4PR17A1 or 4PR17A2. It
may
be
necessary to remove the throw -out hinge, when using
the piano
hinge, in order to meet space
requirements.
DESK, MODEL 4PR18A1
The Desk consists
of
a sturdy, matte black linoleum
-
surfaced top, supported on either end by End Caps
4PR11A1 and 4PR11B1 and enclosed by a
rear panel.
It
can be used to support
a
Top Cabinet, a consolette,
or other types
of
control equipment; or it can
be
used as a desk which matches
the
Base Cabinets,
Models 4PR16A1, -B1, -C1,
and the Monitor Cabinet
Base, Model 4PR12A1.
7