Panasonic WJ-SX 150A Operating Instructions Manual page 70

710 MASTER-SLAVE
MASTER
SLAVE1
SLAVE2
SLAVE3
SLAVE4
"CAUTION"
Part of settings are initialized when
the MASTER-SLAVE composition is changed.
Is the MASTER-SLAVE changed?
SLAVE 1 to 4
ON: Select this for units connected in the system.
OFF: Select this for units not connected in the system.
The factory default setting is OFF.
Notes:
• For Slave units, you can set ON only when the unit with
the previous number is set to ON.
• When you change ON/OFF, part of the setting data will
be initialized according to the master-slave composition
• *. ** is the firmware version of a unit. (For Slave units,
the version is displayed only when ON is selected.)
Is the MASTER-SLAVE changed?
YES: Select this if you agree that the master-slave com-
position will be changed.
NO: Select this if you do not agree that the master-slave
composition will be changed.
This message appears only when you try to change
ON/OFF of SLAVE1 to 4.
• To change the setting, select "YES" and press the SET
button. SETUP MENU will be closed, but the setting will
be activated.
• To cancel the setting, select "NO". The message will
disappear and the cursor moves to the former position.
After the configuration, press the MON (ESC) button. The
monitor display returns to the previous menu.
• LOGICAL CAMERA NUMBER
This menu links to the submenu.
Move the cursor and press the CAM (SET) button to go into
the menu. 720 LOGICAL CAMERA NUMBER will appear on
the monitor.
720 LOGICAL CAMERA NUMBER
SWITCHER=SLAVE1(1 of 4)
CAM LCN
1 1
2 2
3 3
4 4
5 5
6 6
7 7
8 8
LCN:LOGICAL CAMERA NUMBER
73
*.**
ON *.**
ON *.**
OFF *.**
OFF *.**
NO
CAM LCN
9 9
10 10
11 11
12 12
13 13
14 14
15 15
16 16
720 LOGICAL CAMERA NUMBER
SWITCHER=SLAVE2(2 of 4)
CAM LCN CAM
1 17
2 18
3 19
4 20
5 21
6 22
7 23
8 24
LCN:LOGICAL CAMERA NUMBER
720 LOGICAL CAMERA NUMBER
SWITCHER=SLAVE3(3 of 4)
CAM LCN CAM
1 33
2 34
3 35
4 36
5 37
6 38
7 39
8 40
LCN:LOGICAL CAMERA NUMBER
720 LOGICAL CAMERA NUMBER
SWITCHER=MASTER(4 of 4)
CAM LCN CAM
1 --
2 --
3 --
4 --
5 --
6 --
7 --
8 --
LCN:LOGICAL CAMERA NUMBER
Move the joystick to move the cursor.
To select parameters, press the PREV or NEXT button.
SWITCHER: Select a unit (SLAVE1 to 4 and MASTER*) to
configure the parameters
* In normal connection, only MASTER is displayed.
CAM: This stands for a camera channel of the unit.
LCN: This stands for a logical camera number. 1 to 99 is
selectable.
The factory default settings are shown in the diagrams.
When only Master is connected
CAM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
Master 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
When Master and Slave 1 are connected
CAM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
Slave 1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
Master - - - - - - - - 17 18 19 20 21 22 23 24 25 26 27 28
When Master, Slave 1 and 2 are connected
CAM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
Slave 1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
Slave 1 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
Master - - - - - - - - - - - - - - - - 33 34 35 36 37 38 39 40
LCN
9 25
10 26
11 27
12 28
13 29
14 30
15 31
16 32
LCN
9 41
10 42
11 43
12 44
13 45
14 46
15 47
16 48
LCN
9 --
10 --
11 --
12 --
13 49
14 50
15 51
16 52