Bosch ADS 325 User Manual page 33

ss03138
Connected to 2012 Ford Mustang Shelby GT500 5.4L
Read DTCs
Please select one or more controllers and tap 'Continue' to
start DTC scan.
PCM
GEM MODULE / TPMS
OCCUPANT CLASSIFICATION
AUDIO CONTROL MODULE
FRONT CONTROLS INTERFACE MODULE
2. Select the desired vehicle controller then select
continue.
ss03139
Connected to 2012 Ford Mustang Shelby GT500 5.4L | PCM
DTCs
Select Option
Read DTCs
KOEO
KOER
Reset KAM
3. Tapping an option in the menu takes the user to that
test. Follow the prompts on the screen.
ss03140
Connected to 2012 Ford Mustang Shelby GT500 5.4L | PCM
DTCs
Current Codes
B10A2-00 Crash Input
B1200-00 Crash Input Mismatch - CAN
Inactive Hardwired Active
B1207-00 Crash Input Hardwired Signal
4. DTCs will be read from the selected vehicle control-
ler.
• Select a listed DTC for Related Diagnostic Infor-
mation See Diagnostic Information section
• If a DTC has Code Criteria available there will be
an "*" next to the DTC.
Bosch Automotive Service Solutions Inc
Change Vehicle
Select All Deselect All
ABS / TRACTION CONTROL
AIRBAG
ACCESSORY PROTOCOL INTERFACE
BODY CONTROL MODULE
FRONT DISPLAY INTERFACE MODULE
Continue
Change Vehicle
Change Vehicle
Clear DTCs Refresh Share Save Self Diag
Details
Details
Details
Manual DTCs
11:41
Certain vehicles do not support standard DTC protocol
Home
and will require a manual process for retrieving and
clearing codes.
ss03141
Connected to 2002 Subaru Forester Base 2.5L | ABS
DTCs
Manual Codes Procedure
1) Take out diagnosis connector from side of driver's seat heater unit.
2) Turn ignition switch Off.
3) Connect diagnosis connector terminal 6 to diagnosis terminal.
4) Turn ignition switch On.
5) ABS warning light is set in the diagnostic mode and blinks to identify trouble code.
6) After the start code (11) is shown, the diagnostic trouble codes (DTC) will be shown in
1. Follow the prompts on the screen for retreiving DTCs.
ss03142
Home
Connected to 2002 Subaru Forester Base 2.5L | ABS
DTCs
Manual Codes Procedure
1) Take out diagnosis connector from side of driver's seat heater unit.
2) Turn ignition switch Off.
3) Connect diagnosis connector terminal 6 to diagnosis terminal.
4) Turn ignition switch On.
5) ABS warning light is set in the diagnostic mode and blinks to identify trouble code.
6) After the start code (11) is shown, the diagnostic trouble codes (DTC) will be shown in
2. Select Library button.
ss03143
Connected to 2002 Subaru Forester Base 2.5L | ABS
11:42
DTCs
Home
DTCs
11
Manual Codes Procedure
21
1) Take out diagnosis connector from side of driver's seat heater unit.
2) Turn ignition switch Off.
22
3) Connect diagnosis connector terminal 6 to diagnosis terminal.
4) Turn ignition switch On.
23
5) ABS warning light is set in the diagnostic mode and blinks to identify trouble code.
6) After the start code (11) is shown, the diagnostic trouble codes (DTC) will be shown in
3. Follow the prompts on the screen.
ADS 325 | User Manual | 31 | en
Change Vehicle
Clear DTCs Refresh Share Save
Change Vehicle
Clear DTCs Refresh Share Save
Change Vehicle
Start Code: Trouble Code Is Shown
Clear DTCs Refresh Share Save
After Start Code Only Start Code Is
Shown In Normal Condition
Abnormal ABS Sensor (Open Circuit Or
Input Voltage Too High) - Front Right
ABS Sensor
Abnormal ABS Sensor (Abnormal ABS
Sensor Signal) - Front Right ABS
Sensor
Abnormal ABS Sensor (Open Circuit Or
Close
582819 | REV. A | 07.2018
11:44
Home
Code Assist
11:44
Home
Code Assist
11:44
Home
Code Assist