EN60745: Vibration emission (a ) : 5.5 m/s h,AG Model GA4040C, GA4540C, GA5040C Uncertainty (K) : 1.5 m/s Sound pressure level (L ) : 86 dB(A) Work mode : disc sanding with normal side grip Sound power level (L...
Designation of Machine: Uncertainty (K) : 1.5 m/s Angle Grinder Model GA4541C Model No./ Type: GA4040C, GA4540C, GA5040C, Work mode : surface grinding with normal side GA6040C, GA4541C, GA5041C grip Conforms to the following European Directives: Vibration emission (a ) : 6.5 m/s...
Work area safety 17. If devices are provided for the connection of dust extraction and collection facilities, ensure Keep work area clean and well lit. Cluttered or these are connected and properly used. Use of dark areas invite accidents. dust collection can reduce dust-related hazards. Do not operate power tools in explosive atmo- Power tool use and care 18.
Page 5
The rated speed of the accessory must be at least equal to the maximum speed marked on materials. Sparks could ignite these materials. the power tool. Accessories running faster than 16. Do not use accessories that require liquid coolants. Using water or other liquid coolants The outside diameter and the thickness of your may result in electrocution or shock.
Page 6
Additional Safety Warnings: of correct size and shape for your selected When using depressed centre grinding wheels, wheel. thus reducing the possibility of wheel breakage. wheels. Flanges for cut-off wheels may be different from NEVER USE Stone Cup type wheels with this grinder.
For Model GA4040C, GA4041C, GA4540C, GA4541C, FUNCTIONAL GA5040C, GA5041C, GA6040C To start the tool, slide the slide switch toward the "I DESCRIPTION (ON)" position by pushing the rear of the slide switch. For continuous operation, press the front of the slide switch to lock it.
Page 8
Refer to the below table for the relationship between tool. the number settings on the dial and the approximate rotating speed. Installing side grip (handle) For Model GA4040C, GA4540C, GA5040C, GA5040CN, GA4041C, GA4541C, GA5041C Number (R.P.M.) 2,800 4,000...
Page 9
Tighten the wheel guard with fastening the screw after For tool with locking screw type pulling lever in the direction of the arrow. The setting wheel guard To remove wheel guard, follow the installation proce- dure in reverse. Installing or removing depressed accessory) WARNING: so that the closed side of the guard always...
Page 10
Ezynut 1. Ezynut 2. Abrasive wheel 3. counterclockwise. 4. Spindle spindle so that Makita Logo on Ezynut faces outside. (optional accessory) WARNING: on tool. Wheel can shatter during use and guard 1.
Follow instructions for depressed center wheel but also Set the dust cover attachment so that the marking (A, B, use plastic pad over wheel. See order of assembly on C or D) places as shown. Snap its pins in the vents. accessories page in this manual.
Page 12
Operation with abrasive cut-off / diamond wheel (optional accessory) 1. Lock nut 2. Abrasive cut-off wheel/diamond wheel 4. Wheel guard for abrasive cut-off wheel/diamond wheel The direction for mounting the lock nut and the inner below. 100 mm (4") model Abrasive cut-off wheel Diamond wheel Thickness: Less than 4 mm (5/32")
Operation with wire wheel brush WARNING: (optional accessory) wheel, be sure to use only the special wheel guard designed for use with cut-off wheels. (In CAUTION: some European countries, when using a dia- mond wheel, the ordinary guard can be used. tool with no load, insuring that no one is in front Follow the regulations in your country.) of or in line with the wire wheel brush.
CAUTION: in this manual. The use of any other accessories persons. Only use accessory or attachment for its stated purpose. If you need any assistance for more details regard- ing these accessories, ask your local Makita Service Center. 14 ENGLISH...
Page 15
100 mm (4") model 115 mm (4-1/2") model 125 mm (5") model 150 mm (6") model Grip 36 Wheel Guard (for grinding wheel) Inner flange Inner flange Inner flange Inner flange Super flange *1 Super flange *1 Super flange *1 Depressed center wheel/Flap disc Lock nut Lock nut...