Page 2
The contents of this manual are the property of GE Multilin Inc. This documentation is furnished on license and may not be reproduced in whole or in part without the permission of GE Multilin. The content of this manual is for informational use only and is subject to change without notice.
Type tests ..........................2-38 2.5.14 Production tests ........................2-38 2.5.15 Approvals ..........................2-39 2.5.16 Maintenance.........................2-39 3 INSTALLATION Unpack and inspect ....................3-1 Panel cutouts ......................3-2 3.2.1 Horizontal units ........................3-2 3.2.2 Vertical units ........................... 3-6 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 4
Configure modem connection..................3-66 3.7.5 Automatic discovery of UR devices................3-66 Connect to the G30....................3-67 3.8.1 Connect to the G30 in EnerVista................. 3-67 3.8.2 Use Quick Connect via front RS232 port..............3-68 3.8.3 Use Quick Connect via front USB port ..............3-69 3.8.4...
Page 5
Direct inputs and outputs....................5-133 5.3.18 Teleprotection ........................5-139 5.3.19 Installation ..........................5-140 Remote resources ....................5-140 5.4.1 Remote resources configuration ................5-140 System setup.......................5-142 5.5.1 AC inputs ..........................5-142 5.5.2 Power system........................5-143 5.5.3 Signal sources........................5-144 5.5.4 Transformer ........................5-147 5.5.5 Breakers..........................5-158 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 6
RTD inputs .......................... 5-317 5.10.3 DCmA outputs ........................5-318 5.11 Testing ......................... 5-322 5.11.1 Test mode function ......................5-322 5.11.2 Test mode forcing......................5-322 5.11.3 Force contact inputs ..................... 5-323 5.11.4 Force contact outputs ....................5-323 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 7
Data logger ...........................6-29 6.5.5 Breaker maintenance.......................6-29 Product information .................... 6-30 6.6.1 Model information......................6-30 6.6.2 Firmware revisions ......................6-30 7 COMMANDS AND Commands menu ....................7-1 TARGETS 7.1.1 Virtual inputs........................... 7-2 7.1.2 Clear records .......................... 7-2 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 8
11.7 Compare settings ....................11-7 11.7.1 Compare against defaults ..................... 11-8 11.7.2 Compare two devices ...................... 11-8 11.8 Back up and restore settings ................11-9 11.8.1 Back up settings .........................11-9 11.8.2 Restore settings ....................... 11-11 viii G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 9
A FLEXANALOG FlexAnalog items ....................A-1 OPERANDS B RADIUS SERVER RADIUS server configuration ................B-1 CONFIGURATION C COMMAND LINE Command line interface ..................C-1 INTERFACE D MISCELLANEOUS Warranty .........................D-1 Revision history ......................D-1 ABBREVIATIONS INDEX G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 10
TABLE OF CONTENTS G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Ensure that the control power applied to the device, the alternating current (AC), and voltage input match the ratings specified on the relay nameplate. Do not apply current or voltage in excess of the specified limits. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
When contacting GE by e-mail, optionally include a device information file, which is generated in the EnerVista software by clicking the Service Report button. The service report also can be generated in the field, for example with a USB cable connected between the graphical front panel and a computer, and the Device Setup configured for the USB connection.
Page 13
CHAPTER 1: INTRODUCTION FOR FURTHER ASSISTANCE Figure 1-1: Generate service report in EnerVista software G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 14
FOR FURTHER ASSISTANCE CHAPTER 1: INTRODUCTION G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
This chapter outlines the product, order codes, and specifications. 2.1 Product description The G30 Generator Protection System is part of the Universal Relay (UR) series of products. It is a microprocessor-based relay that provides protection, monitoring, control, and recording functions for AC generators driven by steam, gas, or hydraulic turbine.
Rate of change of frequency Phase instantaneous overcurrent Underfrequency 50SP Split phase protection 87RGF Restricted ground fault 50/27 Accidental energization 87GT Generator/transformer differential Ground time overcurrent Figure 2-1: Single-line diagram PTS on transformer HV side G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 17
CHAPTER 2: PRODUCT DESCRIPTION PRODUCT DESCRIPTION Figure 2-2: Single-line diagram PTS on transformer LV side (protection assigned to generator neutral CTS) G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 18
Percent differential Virtual outputs (96) DNP 3.0 or IEC 60870-5-104 protocol Setting groups (6) VT fuse failure Ethernet Global Data Protocol Time synchronization over IRIG-B or IEEE 1588 Event recorder Time synchronization over SNTP G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
When entering a settings or command password via EnerVista or any serial interface, the user must enter the corresponding connection password. If the connection is to the back of the G30, the remote password is used. If the connection is to a front panel port, the local password applies. (These two local and remote password settings are not shown the figure.)
Page 20
Table 2-3: Permissions by user role for CyberSentry Administrator Engineer Operator Supervisor Observer Summary Complete access Complete access Command Authorizes Default role except for menu writing CyberSentry Security Device Definition Settings |---------- Product Setup |--------------- Security (CyberSentry) G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 21
|--------------- Direct Inputs |--------------- Direct Outputs |--------------- Teleprotection |--------------- Direct Analogs |--------------- Direct Integers |---------- Transducer I/O |---------- Testing |---------- Front Panel Labels Designer |---------- Protection Summary Commands |---------- Virtual Inputs |---------- Clear Records G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 22
UR, if the user ID credential does not match one of the five local accounts, the UR forwards automatically the request to a RADIUS server when one is provided. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
The order code is on the product label and indicates the product options applicable. The G30 is available as a 19-inch rack horizontal mount or reduced-size (¾) vertical unit. It consists of the following modules: power supply, CPU, CT/VT, contact input and output, transducer input and output, and inter-relay communications.
G.703, 2 Channels RS422, 1 Channel 7W RS422, 2 Channels 2.3.2 Order codes with process bus modules Table 2-6: G30 order codes for horizontal units with process bus - * ** - * * * - F ** - H **...
Replacement modules can be ordered separately. When ordering a replacement CPU module or front panel, provide the serial number of your existing unit. Not all replacement modules apply to the G30 relay. The modules specified in the order codes for the G30 are available as replacement modules for the G30.
Page 30
4 DCmA inputs, 4 DCmA outputs (only one 5A or 5D module is allowed) 8 RTD inputs 4 RTD inputs, 4 DCmA outputs (only one 5A or 5D module is allowed) 4 DCmA inputs, 4 RTD inputs 8 DCmA inputs 2-16 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 31
4 DCmA inputs, 4 DCmA outputs (only one 5A or 5D module is allowed) 8 RTD inputs 4 RTD inputs, 4 DCmA outputs (only one 5A or 5D module is allowed) 4 DCmA inputs, 4 RTD inputs 8 DCmA inputs G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 2-17...
The UR samples its AC signals at 64 samples per cycle, that is, at 3840 Hz in 60 Hz systems, and 3200 Hz in 50 Hz systems. The sampling rate is dynamically adjusted to the actual system frequency by an accurate and fast frequency tracking system. The analog/digital converter has the following ranges of AC signals: 2-18 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 33
Measured analog values and binary signals can be captured in COMTRADE format with sampling rates from 8 to 64 samples per power cycle. Analog values can be captured with the Data Logger, allowing much slower rates extended over a long period of time. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 2-19...
97% to 98% of pickup Level accuracy: 0.1 to 2.0 × CT: ±0.5% of reading or ±0.4% of rated (whichever is greater) > 2.0 × CT: ±1.5% of reading > 2.0 × CT rating 2-20 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 35
CHAPTER 2: PRODUCT DESCRIPTION SPECIFICATIONS Curve shapes: IEEE Moderately/Very/Extremely Inverse; IEC (and BS) A/B/C and Short Inverse; GE IAC Inverse, Short/Very/ Extremely Inverse; I t; FlexCurves™ (programmable); Definite Time (0.01 s base curve) Curve multiplier: Time Dial = 0.00 to 600.00 in steps of 0.01...
Page 36
±3.5% of operate time or ±1/2 cycle (whichever is greater) from pickup to operate Operate time: <30 ms at 0.9 pickup at 60 Hz for Definite Time mode AUXILIARY UNDERVOLTAGE Pickup level: 0.004 to 3.000 pu in steps of 0.001 2-22 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 37
0.004 to 1.250 pu in steps of 0.001 Dropout level: 97 to 98% of pickup Level accuracy: ±0.5% of reading from 10 to 208 V Pickup delay: 0 to 600.00 s in steps of 0.01 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 2-23...
Page 38
Typical times are average operate times including variables such as frequency change instance, test method, and so on, and can vary by ±0.5 cycles. RATE OF CHANGE OF FREQUENCY df/dt trend: increasing, decreasing, bi-directional df/dt pickup level: 0.10 to 15.00 Hz/s in steps of 0.01 2-24 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 39
Level accuracy: ±0.5% of reading 10 to 208 V Operate Time: <30 ms at 1.10 × pickup at 60 Hz LOSS OF EXCITATION Operating condition: Positive-sequence impedance Characteristic: 2 independent offset mho circles G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 2-25...
Operating signal mode: signed or absolute value Operating mode: level, delta Comparator direction: over, under Pickup Level: –90.000 to 90.000 pu in steps of 0.001 2-26 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 41
FlexLogic operand Pickup delay: 0.000 to 999999.999 s in steps of 0.001 Dropout delay: 0.000 to 999999.999 s in steps of 0.001 Timing accuracy: ±3% or ±4 ms, whichever is greater G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 2-27...
±1.0% of reading at –1.0 ≤ PF < –0.8 and 0.8 < PF ≤ 10 REACTIVE POWER (VARS) Accuracy at 0.1 to 1.5 x CT rating and 0.8 to 1.2 x VT rating: ±1.0% of reading at –0.2 ≤ PF ≤ 0.2 2-28 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
1 sec at 100 times rated continuous 4xInom Short circuit rating: 150000 RMS symmetrical amperes, 250 V maximum (primary current to external CT) AC VOLTAGE VT rated secondary: 50.0 to 240.0 V VT ratio: 1.00 to 24000.00 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 2-29...
Page 44
Amplitude modulation: 1 to 10 V pk-pk DC shift: TTL–Compatible Input impedance: 50 kΩ Isolation: 2 kV DIRECT INPUTS Input points: Remote devices: Default states on loss of comms.: On, Off, Latest/Off, Latest/On 2-30 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
High range power supply: 4 A / 250 V Interrupting capacity: 100 000 A RMS symmetrical 10 000 A 2.5.7 Outputs FORM-A RELAY Make and carry for 0.2 s: 30 A as per ANSI C37.90 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 2-31...
Page 46
48 V 0.5 A 125 V 0.3 A 250 V 0.2 A Operate time: < 8 ms Contact material: silver alloy FAST FORM-C RELAY Make and carry: 0.1 A max. (resistive load) 2-32 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 47
99% Settling time to a step change: 100 ms Isolation: 1.5 kV Driving signal: any FlexAnalog quantity Upper and lower limit for the driving signal: –90 to 90 pu in steps of 0.001 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 2-33...
At extreme temperatures these values deviate based on component tolerance. On average, the output power decreases as the temperature is increased by a factor of 1 dB / 5 °C. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 2-35...
1 phasor metering page for each AC Source 5 tabular metering pages with dynamic metering and status event records page with dynamic update product information page settings, actual values, error messages (targets) 2-36 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
IP20 front, IP10 back (standard front panel and old enhanced front panel) IP40 front, IP10 back (new enhanced front panel) IP54 front with IP54 mounting collar accessory (new enhanced front panel) Ingress protection with IP20 cover accessory: IP20 back Noise: 0 dB G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 2-37...
Insulation: class 1, Pollution degree: 2, Over voltage cat II 1 Not tested by third party. 2.5.14 Production tests THERMAL Products go through an environmental test based upon an Accepted Quality Level (AQL) sampling process. 2-38 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Normally, cleaning is not required. When dust has accumulated on the front panel display, wipe with a dry cloth. To avoid deterioration of electrolytic capacitors, power up units that are stored in a de-energized state once per year, for one hour continuously. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 2-39...
For any issues, contact GE as outlined in the For Further Assistance section in chapter 1. Check that you have the latest copy of the G30 Instruction Manual and the UR Family Communications Guide, for the applicable firmware version, at http://www.gegridsolutions.com/multilin/manuals/index.htm...
3.2.1 Horizontal units The G30 is available as a 19-inch rack horizontal mount unit with a removable front panel. The front panel is specified as enhanced, standard, or graphical at the time of ordering. The enhanced and graphical front panels contain additional user-programmable pushbuttons and LED indicators.
3.2.2 Vertical units The G30 is available as a reduced size (¾) vertical mount unit, with a removable front panel. The front panel is specified as enhanced or standard at the time of ordering. The enhanced front panel contains additional user-programmable pushbuttons and LED indicators.
Page 61
CHAPTER 3: INSTALLATION PANEL CUTOUTS Figure 3-7: Vertical dimensions and mounting (enhanced front panel) G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 62
PANEL CUTOUTS CHAPTER 3: INSTALLATION Figure 3-8: Vertical dimensions and mounting (standard front panel) For side-mounting G30 devices with the enhanced front panel, see the following documents available on the UR DVD and the GE Grid Solutions website: • GEK-113180 —...
Page 63
CHAPTER 3: INSTALLATION PANEL CUTOUTS For side-mounting G30 devices with the standard front panel, use the following figures. Figure 3-9: Vertical side-mounting installation (standard front panel) G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Two-slot wide modules take their slot designation from the first slot position (nearest to CPU module), indicated by an arrow on the terminal block. The figure shows an example of rear terminal assignments. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 3-11...
Page 66
Wire connections to these two modules at 13 inch-pounds. Figure 3-12: CPU modules and power supply The following figure shows the optical connectors for CPU modules. 3-12 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
3.3.2 Dielectric strength Dielectric strength is the maximum electric strength that can be sustained without breakdown. It is measured in volts. The table shows the dielectric strength of the UR-series module hardware. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 3-15...
The power supply module can be ordered for two possible voltage ranges, and the G30 can be ordered with or without a redundant power supply module option. Each range has a dedicated input connection for proper operation. The ranges are as follows (see the Specifications section of chapter 2 for details): •...
Figure 3-17: Control power connection When using a G30 with a HardFiber system, before powering off the G30, save data in the compact flash memory using Commands > Relay Maintenance > Save Non-Volatile Data. When not saved or the relay loses power, up to the last two minutes of data is not saved to the compact flash memory.
Page 72
The phase voltage channels are used for most metering and protection purposes. The auxiliary voltage channel is used as input for the synchrocheck and volts-per-hertz features, which are optional features for some UR models. Substitute the tilde “~” symbol with the slot position of the module in the following figure. 3-18 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Figure 3-19: CT/VT module wiring 3.3.5 Process bus modules The G30 can be ordered with a process bus interface module. The module interfaces with the HardFiber Process Bus System, or HardFiber Brick, allowing bidirectional IEC 61850 fiber-optic communications with up to eight HardFiber Bricks.
Page 74
See the Digital Elements section of chapter 5 for an example of how form-A and solid-state relay contacts can be applied for breaker trip circuit integrity monitoring. Consider relay contacts unsafe to touch when the unit is energized. Death or serious injury can result from touching live relay contacts. 3-20 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 75
Output or Terminal Output or assignment input assignment assignment input assignment input Form-C Fast Form-C Form-A Form-A Form-C Fast Form-C Form-A Form-A Form-C Fast Form-C Form-A Form-A Form-C Fast Form-C Form-A Form-A G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 3-21...
Page 78
WIRING CHAPTER 3: INSTALLATION Figure 3-21: Contact input and output module wiring (Sheet 1 of 3) 3-24 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 79
CHAPTER 3: INSTALLATION WIRING Figure 3-22: Contact input and output module wiring (Sheet 2 of 3) G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 3-25...
Page 80
17 V DC for 24 V sources, 33 V DC for 48 V sources, 84 V DC for 110 to 125 V sources, and 166 V DC for 250 V sources. Figure 3-24: Dry and wet contact input connections Where a tilde “~” symbol appears, substitute the slot position of the module. 3-26 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 81
G30 input even when the output is open, if there is a substantial distributed capacitance (represented by C1) present in the wiring between the output and the G30 input, and the debounce time setting in the G30 relay is low enough.
Page 82
To prevent this operation, the debounce time must be increased to 4 ms (set debounce time as per the following table) or insert a resistor less than or equal to "R" as calculated later. Table 3-5: Typical debounce time setting Stray capacitance (μF) Battery voltage (V) Debounce time (ms) 0.05 0.05 3-28 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 83
Eq. 3-2 The 2 mA current is used in case the contact input is connected across the GE Form A contact output with voltage monitoring. Otherwise use the amperage of the active circuit connected to the contact input when its contact output is open and the voltage across the contact input is third trigger threshold to calculate the resistor value.
Page 84
Contact inputs can be susceptible to parasitic capacitance, caused by long cable runs affected by switching surges from external circuits. This can result in inadvertent activation of contact inputs with the external contact open. In this case, GE recommends using the contact I/O module with active impedance circuit.
The following figure illustrates the transducer module types (5A, 5C, 5D, 5E, and 5F) and channel arrangements that can be ordered for the relay. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 3-31...
Page 86
WIRING CHAPTER 3: INSTALLATION Where a tilde “~” symbol appears, substitute the slot position of the module. Figure 3-30: Transducer input/output module wiring The following figure show how to connect RTDs. 3-32 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
RS232 port is shown in the following figure for the nine-pin connector on the UR and nine or 25-pin connector on a computer. The baud rate for this port can be set, with a default of 115200 bps. Figure 3-32: RS232 front panel port connection G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 3-33...
3.3.9 CPU communication ports 3.3.9.1 Overview There is a rear RS485 communication port on the CPU module. The CPU module does not require a surge ground connection. Figure 3-33: CPU module communications wiring 3-34 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 89
This common voltage is implied to be a power supply common. Some systems allow the shield (drain wire) to be used as common wire and to connect directly to the G30 COM terminal (#3); others function correctly only if the common wire is connected to the G30 COM terminal, but insulated from the shield.
IRIG-B is a standard time code format that allows stamping of events to be synchronized among connected devices. The IRIG-B code allows time accuracies of up to 100 ns. The GE MultiSync 100 1588 GPS Clock as well as third-party equipment are available for generating the IRIG-B signal.
UR1-Tx1 to UR2-Rx1, UR2-Tx1 to UR3-Rx1, UR3-Tx1 to UR4-Rx1, and UR4-Tx1 to UR1-Rx1 for the first ring; and UR1-Tx2 to UR4-Rx2, UR4-Tx2 to UR3-Rx2, UR3-Tx2 to UR2-Rx2, and UR2-Tx2 to UR1-Rx2 for the second ring. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 3-37...
Page 92
Those that apply depend on options purchased. The options are outlined in the Inter-Relay Communications section of the Order Code tables in Chapter 2. All of the fiber modules use ST type connectors. 3-38 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
The following figure shows the configuration for the 72, 73, 7D, and 7K fiber-laser modules. Figure 3-41: 7x Laser fiber modules The following figure shows configuration for the 2I and 2J fiber-laser modules. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 3-39...
X1a or X6a is used to ground the shield at one end, do not ground the shield at the other end. This interface module is protected by surge suppression devices. Figure 3-43: G.703 interface configuration 3-40 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 95
Once the clips have cleared the raised edge of the chassis, engage the clips simultaneously. When the clips have locked into position, the module is inserted fully. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 3-41...
Page 96
(S1 = ON) and set timing mode to loop timing (S5 = OFF and S6 = OFF). The switch settings for the internal and loop timing modes are shown. 3-42 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 97
One source lies on the G.703 line side of the interface while the other lies on the differential Manchester side of the interface. Figure 3-48: G.703 dual loopback mode G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 3-43...
(data module 1) connects to the clock inputs of the UR RS422 interface in the usual way. In 3-44 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 99
Figure 3-51: Timing configuration for RS422 two-channel, three-terminal application Data module 1 provides timing to the G30 RS422 interface via the ST(A) and ST(B) outputs. Data module 1 also provides timing to data module 2 TT(A) and TT(B) inputs via the ST(A) and AT(B) outputs. The data module pin numbers have been omitted in the figure because they vary by manufacturer.
For the direct fiber channel, address power budget issues properly. When using a laser interface, attenuators can be necessary to ensure that you do not exceed maximum optical input power to the receiver. Figure 3-53: RS422 and fiber interface connection 3-46 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Connection — as per all fiber-optic connections, a Tx-to-Rx connection is required The UR-series C37.94 module can be connected directly to any compliant digital multiplexer that supports the IEEE C37.94 standard. The figure shows the concept. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 3-47...
Page 102
5.60. For customers using firmware release 5.60 and higher, the module can be identified with "Rev D" printed on it and is to be used on all ends of G30 communication for two and three terminal applications.
Page 103
When the clips have locked into position, the module is inserted fully. Figure 3-58: IEEE C37.94 timing selection switch setting Modules shipped since January 2012 have status LEDs that indicate the status of the DIP switches, as shown in the following figure. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 3-49...
Fiber-optic cable length — Up to 11.4 km • Fiber-optic connector — Type ST • Wavelength — 1300 ±40 nm • Connection — As per all fiber-optic connections, a Tx-to-Rx connection is required 3-50 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 105
5.60. For customers using firmware release 5.60 and higher, the module can be identified with "Rev D" printed on it and is to be used on all ends of G30 communication for two and three terminal applications.
Page 106
When the clips have locked into position, the module is inserted fully. Figure 3-61: C37.94SM timing selection switch setting Modules shipped since January 2012 have status LEDs that indicate the status of the DIP switches, as shown in the following figure. 3-52 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Press the right arrow until the message displays. MESSAGE SECURITY Press the down arrow until the message displays. MESSAGE INSTALLATION Press the right arrow until the Not Programmed message displays. MESSAGE RELAY SETTINGS: G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 3-53...
To communicate via the RS232 port, use a standard straight-through serial cable. Connect the DB-9 male end to the relay and the DB-9 or DB-25 female end to the computer COM2 port as described in the CPU Communication Ports section earlier in this chapter. 3-54 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
This device (catalog number F485) connects to the computer using a straight-through serial cable. A shielded twisted-pair wire (20, 22, or 24 AWG) connects the F485 converter to the G30 rear communications port. The converter terminals (+, –, GND) are connected to the G30 communication module (+, –, COM) terminals. See the CPU Communication Ports section in chapter 3 for details.
Add Now button to list software items for the product. EnerVista Launchpad obtains the software from the Internet or DVD and automatically starts the installation program after prompting about updates. From the web, the software is downloaded. A wizard opens. 3-56 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
You connect remotely to the G30 through the rear RS485 or Ethernet port with a computer running the EnerVista UR Setup software. The G30 also can be accessed locally with a computer through the front panel RS232 or USB port or the rear Ethernet port using the Quick Connect feature.
Online Window area, cannot be moved from it to another grouping, and needs to be renamed in the Device Setup window. GE instead recommends using the Device Setup window to add devices, as outlined here. 3.7.1 Set IP address in UR The IP and subnet addresses need to be added to the UR for Ethernet communication.
Page 113
CHAPTER 3: INSTALLATION ADD DEVICE TO SOFTWARE connections window. Or in Windows 7, access the Network and Sharing Center in the Control Panel. Right-click the Local Area Connection icon and select Properties. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 3-59...
Page 114
Select the Internet Protocol (TCP/IP) item from the list, and click the Properties button. Click the “Use the following IP address” box. Enter an IP address with the first three numbers the same as the IP address of the G30 relay and the last number different (in this example, 1.1.1.2).
Page 115
Minimum = 0ms, Maximum = 0ms, Average = 0 ms Pinging 1.1.1.1 with 32 bytes of data: verify the physical connection between the G30 and the computer, and double-check the programmed IP address in setting, then repeat step 2. PRODUCT SETUP COMMUNICATIONS NETWORK IP ADDRESS...
Page 116
Click the Quick Connect button to open the window. Select the Ethernet interface and enter the IP address assigned to the G30, then click the Connect button. The EnerVista UR Setup software creates a site named “Quick Connect” with a corresponding device also named “Quick Connect”...
For the RS232 connection, a computer with an RS232 port and a serial cable are required. To use the RS485 terminals at the back of the relay, a GE Grid Solutions F485 converter (or compatible RS232-to-RS485 converter) is required. See the F485 instruction manual for details.
Page 118
Processor, such as an SEL-2030 or SEL-2032. This option enables display of a terminal window to allow interaction with the other device. Click the Read Order Code button to connect to the G30 and upload the order code to the software. If a communications error occurs, ensure that the EnerVista software serial communications values entered in the previous step correspond to the relay setting values, and also ensure that the same IP address is not assigned to multiple G30 ports.
10. If using a gateway to connect to the device, select Yes from the drop-down list. 11. Click the Read Order Code button to connect to the G30 device and upload the order code. If the device was entered already, a message displays "Device ’x’ is also using IP address.." If a communications error occurs, ensure that the values entered in the previous steps correspond to the relay setting values, and also ensure that the same IP address G30 GENERATOR PROTECTION SYSTEM –...
12. Click the OK button when the relay order code has been received. The new site and device are added to the Online Window. The device has been configured for Ethernet communications. Proceed to the Connect to the G30 section to begin communications.
When unable to connect because of an "ACCESS VIOLATION," access Device Setup and refresh the order code for the device. When unable to connect, ensure that the same IP address is not assigned to multiple G30 ports, for example under Settings > Product Setup > Communications > Network.
View the G30 protection summary • View all of the G30 metering values • View the status of all G30 inputs and outputs • Generate a service report 3.8.2 Use Quick Connect via front RS232 port This feature applies to the enhanced and standard front panels.
Click the Quick Connect button to open the window. Select the USB Interface and the "GE Virtual Serial Port" driver from the drop-down list, then click Connect. If the GE driver does not display, it means that the USB cable was connected on Windows 10 when upgrading the UR software.
Connect" and displays them in the Online Window. Expand the sections to view data directly from the G30 device. Use the Device Setup button to change the site name. Each time that the EnerVista software is initialized, click the Quick Connect button to establish direct communications to the G30.
URS — When not IEC 61850 and version is lower than 7.30, the file is added and time stamp is unchanged. When clicking in the software on the tree element, a device folder is created, the original file moves into it, and time stamp is on the URS file is retained. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 3-71...
3.11 Connect to D400 gateway A GE Multilin D400 Substation Gateway can be used to collect data from UR devices in a local area network (LAN). It collects metering, status, event, and fault report data from serial or LAN-based intelligent substation devices, and it pre-processes the data.
These are the configuration/settings files in the IEC 61850 SCL/IID format. The ur.iid file is saved with a "_YYMMDDhhmmss" retrieval time stamp, for example ur_170525183124.iid. It is stored in the D400 folder system using the UR site and device name. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 3-73...
Page 128
CONNECT TO D400 GATEWAY CHAPTER 3: INSTALLATION 3-74 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
The EnerVista UR Setup software is provided with every G30. This chapter outlines the EnerVista software interface. The EnerVista UR Setup help file in the software also provides details for getting started and using the software interface.
IP Address IP Subnet Mask IP Routing When a settings file is loaded to a G30 that is in-service, the following sequence occurs: The G30 takes itself out of service. The G30 issues a UNIT NOT PROGRAMMED major self-test error.
Site list / online window area Settings list / offline window area Software windows, with common toolbar Settings file data view windows, with common toolbar Workspace area with data view tabs Status bar 10. Quick action hot links G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
4.1.6 Protection summary window The Protection Summary is a graphical user interface to manage elements, such as enabling and disabling them. Access it under Settings > Protection Summary. See the Settings chapter for information on use. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
The settings file template is now enabled and the file menus display in light blue. The settings file is now in template editing mode. To undo the action, select Template Mode > Remove Template. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 134
Figure 4-4: Settings template with all settings specified as locked Specify the settings to make viewable by clicking them. A setting available to view displays with a yellow background. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 135
4.1.7.3 Add password protection to a template GE recommends that templates be saved with password protection to maximize security. When templates are created for online settings, the password is added during the initial template creation step. It does not need to be added after the template is created.
Page 136
Once the template has been applied, users are limited to edit the settings specified by the template, but all settings are shown. The effect of applying the template to the phase time overcurrent settings is shown as follows. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
EnerVista UR Setup is in EDIT mode. Specify the entries to lock by clicking them. The locked entries display a grey background as shown in the example. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 138
The effect of applying the template to the FlexLogic entries is shown here. Figure 4-10: Locking FlexLogic entries through settings templates The FlexLogic entries are also shown as locked in the graphical view and on the front panel display. 4-10 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 139
Actual Values > Product Info > Model Information, the inside front panel, and the rear of the device. Right-click the setting file in the Offline Window area and select the Edit Device Properties item. The window opens. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 4-11...
When a settings file is transferred to a G30 device, the date, time, and serial number of the G30 are sent back to EnerVista UR Setup and added to the settings file on the local computer. This information can be compared with the G30 actual values at any later date to determine if security has been compromised.
Page 141
• The transfer date of a settings file written to a G30 is logged in the relay and can be viewed in the EnerVista software or the front panel display. Likewise, the transfer date of a settings file saved to a local computer is logged in the EnerVista software.
Page 142
4.1.9.2 Online device traceability information The G30 serial number and file transfer date are available for an online device through the actual values. Select the Actual Values > Product Info > Model Information menu item within the EnerVista online window as shown in the example.
The enhanced front panel consists of LED panels, an RS232 port, keypad, LCD display, control pushbuttons, and optional user-programmable pushbuttons. The front panel is hinged to allow access to removable modules inside the chassis. The G30 enhanced front panel can be horizontal or vertical. The following figure shows the horizontal front panel.
Page 144
IEC 61850. The USB port connects to a computer with the EnerVista software and can be used to upgrade the relay and to transfer files and settings. The USB port is the square type B. 4-16 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
The front panel can be viewed and used in the EnerVista software, for example to view an error message displayed on the front panel or the LEDs. To view the front panel in EnerVista software: Click Actual Values > Front Panel, then any option. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 4-17...
Page 146
IRIG-B, SNTP, and so on, the date/time is shown in white, and otherwise in yellow. On pages other than the home page, the header displays the name of the page. The footer dynamically labels the Tab, or control, pushbuttons immediately below. Page content displays between the header and footer. 4-18 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 147
RESET button clears those messages that can be. Configure the home page in the software under Settings > Product Setup > Graphical Panel > Home Page. The menu does not display when there is no graphical front panel. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 4-19...
Page 148
Factory default names are SLD 1 to SLD 5. Pages that have no configured content have a blank Tab pushbutton label, and the Tab pushbutton does nothing. The label for the current page has a blue background. Figure 4-24: Toolbar options for single-line diagram 4-20 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 149
Figure 4-25: Single-line diagram of open circuit breakers Under Settings > System Setup > Switches and Breakers, enable and name the six switches and two breakers. Switch 6, M568G, has the A/3 Pole Opened setting on. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 4-21...
Page 150
Line Diagram Editor. Add the four switches for the top line by clicking the GE switch symbol in the toolbar, then clicking in the window. (If the UR device is not online, the software attempts to connect.) Right-click to edit properties. Rotate switches SW569 and SW5682 to 270 degrees.
Page 151
Figure 4-27: Single-line diagram on graphical front panel Press the Enable Control pushbutton. The side pushbutton labels display. Figure 4-28: Side pushbutton display on graphical front panel Press the CB523 breaker pushbutton. Its menu displays. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 4-23...
Page 152
To add a line component, click it in the toolbox, then click in the window. Double-click a line to open its properties window to set orientation. Figure 4-30: Line and bus crossover symbols 4-24 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 153
Each breaker and disconnect component can be configured to use UR-style symbols, IEC symbols, or simple square/slash symbols as shown in the following figure. The symbols assume horizontal symbol orientation, red - closed color, and green - open scheme. With vertical orientation, they are rotated 90 degrees. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 4-25...
Page 154
(horizontal or vertical), color scheme (red - closed, or red - open), and assigned side button (if any). If the selected breaker or disconnect element does 4-26 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 155
A question mark displays in a symbol on the graphical front panel when status is bad. The question mark does not rotate with orientation. Figure 4-34: Symbols when status is bad The following figures show the orientation available for the static components. The default position is 0 degrees. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 4-27...
Page 156
FRONT PANEL INTERFACE CHAPTER 4: INTERFACES Figure 4-35: Single-line diagram static symbol orientation (sheet 1 of 2) 4-28 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 157
User-programmable pushbuttons 9 to 16 can be programmed among the 10 pushbuttons on the left and right sides of the screen display. They show dynamically and provide a means to perform the same control as the other pushbuttons. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 4-29...
Page 158
To add a metering component, click the M symbol in the toolbox, then click in the window. Drag it to its final location. Double-click it to open the properties window. The figure shows the properties that can be edited. 4-30 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 159
Self Reset, so the alarm displays in a solid color. The blue alarm type is Acknowledgeable, so the alarm flashes until it is acknowledged, for example by navigating with the arrow keys and pressing the ENTER button. The alarm then remains blue until the trigger condition is eliminated. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 4-31...
Page 160
FlexLogic operand. The self-reset mode alarm sequence conforms to ISA-18.1-1979 (R2004) standard type A 4 5 6. Figure 4-40: Annunciator alarm sequence in Self Reset mode 4-32 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 161
An alarm remains in an alarm state (for example, displays red) when the condition remains. That is, if you acknowledged a flashing alarm but the alarm condition remains, the background color remains red. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 4-33...
Page 162
The three page layouts (3 × 4, 4 × 6, and 6 × 8) select the number of rows x columns of windows that appear in a page. Annunciator window size and text size shrink as the number of annunciator windows in a page increases. 4-34 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 163
Content to display is configured with the cell lines. The content can be actual values, a status indicator, or text. • Actual value — Select from the FlexAnalogs applicable to the G30, where a FlexAnalog is an analog parameter G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 164
Save — Updates the connected device if online or the open setting file if offline with changes made • Restore — Undoes changes that have not been saved • Default — Changes all settings in the window to factory default values 4-36 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
ESCAPE — If a setting is open for edit, this pushbutton closes the setting without saving. If a popup menu is open, this pushbutton closes it. If an item is selected, this pushbutton deselects it. Otherwise this pushbutton activates the previous page in the page hierarchy. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 4-37...
IN SERVICE — Indicates that control power is applied, all monitored inputs/outputs and internal systems are fine, and the relay is in (online) Programmed mode (under Settings > Product Setup > Installation) 4-38 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 167
Support for applying a customized label beside every LED is provided. Default labels are shipped in the label package of every G30, together with custom templates. The default labels can be replaced by user-printed labels. User customization of LED operation is of maximum benefit in installations where languages other than English are used to communicate with operators.
Page 168
PHASE A — Indicates phase A was involved • PHASE B — Indicates phase B was involved • PHASE C — Indicates phase C was involved • NEUTRAL/GROUND — Indicates that neutral or ground was involved 4-40 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 169
TROUBLE — Indicates that the relay has detected an internal problem. Check the self-test messages outlined at the end of the Commands and Targets chapter, and view the event records under Actual Values > Records. For a beta / pre-release, this LED is always on. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 4-41...
Page 170
PHASE B — LED 12 — Indicates phase B was involved • PHASE C — LED 13 — Indicates phase C was involved • NEUTRAL/GROUND — LED 14 — Indicates that neutral or ground was involved 4-42 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
FRONT PANEL INTERFACE 4.2.5 Front panel labelling 4.2.5.1 Enhanced front panel The following procedure requires these pre-requisites: • The UR front panel label cutout sheet (GE part number 1006-0047) has been downloaded from http://www.gegridsolutions.com/products/support/ur/URLEDenhanced.doc and printed • Small-bladed knife To create custom LED and pushbuttons labels for the enhanced front panel: Start the EnerVista UR Setup software.
Page 172
FRONT PANEL INTERFACE CHAPTER 4: INTERFACES The label package shipped with every G30 contains the three default labels, the custom label template sheet, and the label removal tool. If the default labels are suitable for your application, insert them in the appropriate slots and program the LEDs to match them.
Page 173
Slide the new LED label inside the pocket until the text is properly aligned with the LEDs, as shown. To remove the user-programmable pushbutton labels from the G30 front panel and insert the custom labels: Use the knife to lift the pushbutton label and slide the tail of the label tool underneath, as shown. Ensure that the bent G30 GENERATOR PROTECTION SYSTEM –...
Page 174
Remove the tool and attached user-programmable pushbutton label. Slide the new user-programmable pushbutton label inside the pocket until the text is properly aligned with the 4-46 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 175
To create LED and pushbutton labels for a standard front panel: In the EnerVista software, if the G30 is not already listed in the Offline Window area, add it by right-clicking it and selecting the Add Device to Offline Window option.
Page 176
4.2.5.3 Graphical front panel The G30 includes software for labelling the LEDs and pushbuttons on the graphical front panel and a sticker sheet with pre-printed and blank labels. The pre-printed labels are on the top-left of the template sheet, and the blank labels are on the bottom-right.
Use the down, right, left, and up arrows to navigate the menu. The up and down arrow keys move within a group of headers, sub-headers, setting values, or actual MESSAGE G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 4-49...
Page 178
The Page Up and Page Down Tab pushbuttons also navigate through the list. When there is only a single page of options, they jump to the first and last entries. The options displayed depend on order code. 4-50 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
This flash message momentarily appears as confirmation of the storing process. Numerical values that contain decimal places are rounded-off if more decimal place digits are entered than specified by the step value. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 4-51...
Page 180
An example is a confirmation message upon saving settings. This setting specifies how long to display the message. Press the Menu pushbutton to display the main menu. 4-52 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 181
Figure 4-56: Main menu Use the Up or Down pushbutton to select SETTINGS, then press the Right or ENTER pushbutton. Figure 4-57: Settings menu With PRODUCT SETUP selected, press the Right or ENTER pushbutton. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 4-53...
Page 182
Pressing the ENTER pushbutton with the - key selected inverts the sign. Pressing the ENTER pushbutton with the decimal point selected enters that character at the insertion point. Push ENTER now to accept the 4. 4-54 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 183
To add accents, highlight a key and hold the ENTER pushbutton on the graphical front panel. Any special characters associated with the key display. Figure 4-61: Settings page with keyboard and accents G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 4-55...
Phasor pages that have no configured CTs or VTs do not have a Tab pushbutton, and phasor pages that have no configured cells cannot be displayed. Figure 4-62: Phasor display The configurable name displays in the header and Tab pushbutton label. Factory default names are Page 1, Page 2, and so 4-56 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
4.2.9 Breaker control The G30 can interface with associated circuit breakers. In many cases the application monitors the state of the breaker, that can be presented on front panel LEDs, along with a breaker trouble indication. Breaker operations can be manually initiated from the front panel keypad or automatically initiated from a FlexLogic operand.
When entering a settings or command password via EnerVista or any serial interface, the user must enter the corresponding connection password. If the connection is to the back of the G30, the remote password must be used. If the connection is to the RS232 port of the front panel, the local password must be used.
By default, when an incorrect Command or Setting password has been entered via the front panel three times within five minutes, the FlexLogic operand is set to “On” and the G30 does not allow settings or command level LOCAL ACCESS DENIED access via the front panel for five minutes.
Not. Negates/reverses the output, for example 0 becomes 1. Connection S, R Set, Reset Timer pickup. Triggered by the settings latch in the diagram. Timer reset. Triggered by the reset latch in the diagram. 4-60 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Works with all UR firmware versions The figure shows an example where several inputs are used to trigger an output. With the OR function, any one of the inputs can trigger the output. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 4-61...
Page 190
This section explains how to use Engineer. It outlines the following topics: • Design logic • Send file to and from device • Monitor logic • View front panel • Generate connectivity report • Preferences 4-62 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Preparation — Under Settings > Inputs/Outputs > Virtual Outputs, virtual outputs 3 and 4 are named DLTrigger Top logic — Seven-minute timer trigger Bottom logic — Turn on LED 9 for 10 seconds when the trigger starts G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 4-63...
Page 192
This procedure uses input / output logic as an example. To create a logic diagram: In the Offline Window area, access Engineer for the device, then Logic Designer. If the device is not listed, right-click 4-64 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 193
Optionally delete the default logic diagram by right-clicking its tab at the bottom of the window and selecting Delete. To add a blank sheet, click Edit > Add Sheet. A new tab displays. Or use the last tab displayed, which is a blank sheet. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 4-65...
Page 194
Line option. The cursor needs to be at the connection point to end the line, not elsewhere on the block. Note that the outline color is no longer red on the blocks. 4-66 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 195
The warning "input using disabled feature" means that input needs to be enabled. Double-click the block, click the View Associated Screen button, enable the setting, save, and recompile. The output and messages are explained in the next section. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 4-67...
Page 196
IEC 61850 panel and thereby become synchronized. The CID file and the IID file (depending on the preference 'Do not update IID file when updating SCL files') are updated. If the CID file is not already there, it is generated. 4-68 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 197
FLEXLOGIC DESIGN USING ENGINEER The location of these files is C:\ProgramData\GE Power Management\urpc, for example, in the Offline and Online folders. Any FlexLogic equations entered in the Offline Window area are erased. The logic drawn in the Logic Designer window in Engineer in the Offline Window area remain.
Page 198
Click the Ok button to save and exit from the window. In the logic diagram, select an element, then click in the drawing area to add it, click again to add a second box, and so on. 4-70 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 199
Optimization Summary. Changes also display when the FlexLogic Equation Editor is accessed. The logic diagram does not change. In the example shown, no lines were saved to free up space. Figure 4-81: Code optimization results G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 4-71...
Page 200
Type in the second text string box, or select any of the 32 previous searches from the drop-down list. Click the Search button. Any results display. The search applies to all tabs, not just the active tab. Double-click a search result to view the item. 4-72 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
When a window opens, select the device to which you want to send the file, then click the Send button and confirm. The order codes must match. The file is sent to the live device. Any errors can be viewed in the log file at the prompt. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 4-73...
(green box outline). In this case, the battery is weak and needs to be replaced. This can be viewed as the Replace Battery message on the front panel of the device and in the EnerVista software under Actual Values > Front Panel > Front Panel or Display/Keypad. 4-74 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
To save the report and labels, click File > Save As, enter a file name, and select the FPR, JPG, or PDF format. Use the instructions in the second tab of the window to add the labels to the physical device. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 4-75...
View > Toolbar > Advanced Actions — Active when in Logic Designer. Toggles a toolbar to nudge, rotate, flip, or change the order of an element. View > Show Unused Pins — Enable to display unconnected pins. Disable to eliminate unconnected pins from the view, for example when printing. 4-76 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 205
File Information The text entered here displays at the bottom right of a diagram when printing, provided that the Show Title Block option is enabled. Note the option to change the logo from the GE logo to your company logo. Display The panel sets how the element boxes display.
Page 206
The software displays the color specified when an element is on. There is no color when the element is off. The software displays another color when the status cannot be determined and is unknown. 4-78 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 207
Options display for filtering, such as recording timing for Virtual Inputs and Outputs, but not Communications Status. 4.4.6.4 COMTRADE waveforms Waveform files are viewable in the EnerVista software. The preferences are unrelated to Engineer and are outlined in the UR Family Communications Guide. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 4-79...
When you re-launch the EnerVista software, communication is on by default. 4.4.7.2 Token Toolbox Drawing Tools Draw a line. Click and drag to draw. Draw multiple joined lines. Click and drag for each line. Double-click to finish. 4-80 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 209
Remote inputs from other devices Input from another UR device. Teleprotection inputs/outputs and direct inputs/outputs are mutually exclusive and cannot be used simultaneously. Teleprotection inputs/outputs and direct inputs/outputs are mutually exclusive and cannot be used simultaneously. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 4-81...
Page 210
Tag-In can is used to reference an existing Tag-Out. It joins another diagram to a previous diagram. Boolean Tokens These symbols are used to create FlexLogic Equations. Use them as intermediate logic for the Virtual Output equations. The display can vary from that shown here. 4-82 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 211
Place a positive one shot and a negative one shot symbol in the Logic Designer diagram Place a timer in the Logic Designer diagram Elements These blocks configure properties of the element or use element operands as input to FlexLogic equations. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 4-83...
Page 212
Set the width of the selected components to the same width as the reference component Same Height Set the height of the selected components to the same height as the reference component 4-84 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 213
Front, Back Moves current components to the absolute front or back of all viewable layers Forward, Backward Moves current components on layer higher or lower than its original layer hierarchy G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 4-85...
Page 214
FLEXLOGIC DESIGN USING ENGINEER CHAPTER 4: INTERFACES 4-86 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
VT ratio setting is set to the nominal ratio of the VTs and the secondary voltage setting is set to the phase-to-phase voltage seen by the relay when the voltage of the protected system in nominal. The UR uses the convention that nominal voltages in a three-phase system are phase-to-phase voltages. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 219
Not every operand of a given element in a UR relay generates events, only the major output operands. Elements, asserting output per phase, log operating phase output only, without asserting the common three-phase operand event. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
For example, in the scheme shown in the preceding figure, the user configures one source to be the sum of CT1 and CT2 and can name this source as “Wdg1 I.” G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
(as described earlier) as follows for a maximum configuration: F1, F5, M1, M5, U1, and U5. 5.3 Product setup 5.3.1 Security 5.3.1.1 Security overview The following security features are available: • Password security — Basic security present by default G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 222
To reset the unit after a lost password: Email GE customer service at multilin.tech@ge.com with the serial number and using a recognizable corporate email account. Customer service provides a code to reset the relay to the factory defaults.
Page 223
When entering a settings or command password via EnerVista or any serial interface, the user must enter the corresponding connection password. If the connection is to the back of the G30, the remote password must be used. If the connection is to the RS232 port of the front panel, the local password must be used.
Page 224
When an original password has already been used, enter it in the Enter Password field and click the Send Password to Device button. Re-enter the password in the Confirm Password field. 5-10 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 225
INVALID ATTEMPTS BEFORE LOCKOUT The G30 provides a means to raise an alarm upon failed password entry. If password verification fails while accessing a password-protected level of the relay (either settings or commands), the FlexLogic operand is UNAUTHORIZED ACCESS asserted.
Page 226
ACCESS AUTH TIMEOUT immediately denied. If access is permitted and an off-to-on transition of the FlexLogic operand is detected, the timeout is restarted. The status of this timer updates every five seconds. 5-12 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 227
It is disabled by default to allow access to the device immediately after installation. When security is disabled, all users have administrator access. GE recommends enabling the EnerVista security before placing the device in service. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 228
If you force password entry by using this feature, ensure that you know the Administrator password. If you do not know the password and are locked out of the software, contact GE Grid Solutions for the default password of a UR device.
Page 229
The EnerVista security management system must be enabled (the Enable Security check box enabled) To modify user privileges: Select the Security > User Management item from the top menu to open the user management window. Locate the username in the User field. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-15...
Page 230
This feature requires a CyberSentry software option. See the Order Codes section in chapter 2 for details. The EnerVista software provides the means to configure and authenticate the G30 access using either a server or the device. Access to functions depends on user role.
Page 231
When the "Device" button is selected, the G30 uses its local authentication database and not the RADIUS server to authenticate the user. In this case, it uses built-in roles (Administrator, Engineer, Supervisor, Operator, Observer, or Administrator and Supervisor when Device Authentication is disabled), as login accounts and the associated passwords are stored on the G30 device.
Page 232
Figure 5-3: Security panel when CyberSentry installed For the Device > Settings > Product Setup > Supervisory option, the panel looks like the following. Figure 5-4: Supervisory panel For the Security panel, the following settings are available. 5-18 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 233
Administrator is to re-enable Device authentication when Device authentication is disabled. To re-enable Device authentication, the Supervisor unlocks the device for setting changes, and then the Administrator can re- enable Device authentication. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-19...
Page 234
LOGIN: Range: Administrator, Engineer, Supervisor, None Operator, Factory (for factory use only), None CHANGE LOCAL See page 5-21 PASSWORDS SESSION See page 5-22 SETTINGS 5-20 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 235
• Observer — This role has read-only access to all G30 settings. This role allows unlimited concurrent access but it has no download access to any files on the device. Observer is the default role if no authentication has been done to the device.
Page 236
In Device authentication mode, the Observer role does not have a password associated with it. In Server authentication mode the Observer role requires a password. If you are locked out of the software, contact GE Grid Solutions for the default password. When using CyberSentry, the default password is "ChangeMe1#".
Page 237
RS232 and RS485 connections. The default value is 1 minute. GE recommends setting this value to at least 3 minutes for the following scenario: while connected to a CyberSentry device, with serial or USB cable connected to the front panel, and performing "Add Device to Offline Window" or an online/ offline comparison.
Page 238
Supervisor, Engineer, Operator, Observer) in the RADIUS server. If you do, the UR relay automatically provides the authentication from the device. In the EnerVista software, choose Server authentication and log in using the user name and password configured on the RADIUS server for Server authentication login. 5-24 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 239
Clear Demand Records command (not applicable to all UR products) Clear Energy command (not applicable to all UR products) Clear Unauthorized Access command Clear Teleprotection Counters command (not applicable to all UR products) Clear All Relay Records command Role Log in G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-25...
Enumeration Description Role Log off In addition to supporting syslog, a G30 with CyberSentry also saves the security events in two local security files, these being SECURITY_EVENTS.CSV and SETTING_CHANGES.LOG. Details on these files and how to retrieve them are available in the EnerVista software under Maintenance >...
Page 241
Some customers prefer very low currents to display as zero, while others prefer the current to display even when the value reflects noise rather than the actual signal. The G30 applies a cut-off value to the magnitudes and angles of the measured currents.
Annunciator Editor and Single Line Diagram Editor can be open and active, then subsequently opened Rolling Mode and Home Page screens are read-only. Close the windows, then re-open the one required. 5-28 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 243
Visual and audible signals are given when conditions return to normal, then the sequence returns to normal by pushing the RESET button. – The first annunciator page that contains an annunciator window that is in abnormal state – Annunciator page 1 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-29...
Page 244
Similarly, the display backlight intensity is lowered to a specified level; lower intensity extends the life of the display. Each rolling page displays for a few seconds; duration cannot be set. The path is Settings > Product Setup > Graphical Panel > Rolling Mode. 5-30 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 245
Range: 1 to 10 in steps of 1 Default: 1 This setting specifies the number of rolling pages. During rolling mode, the graphical front panel displays pages from 1 to the selected number. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-31...
Page 246
For a phasor diagram, configure the source under Settings > System Setup > Signal Sources. The diagram is then viewable by pushing the Metering Tab pushbutton on the graphical front panel. The Metering Editor is not used for these phasor diagrams. The figures show setup and table preview. 5-32 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 247
A maximum of eight Status Inputs can be used per metering page, and 16 in all metering pages. Select the metering input from the drop-down list. The options reflect the FlexLogic operands applicable to the G30. They are inputs for all five metering pages, not just the current page.
Page 248
Range: 16, 18, 20 Default: 16 Set the font size to display on the graphical front panel. TEXT COLOR Range: 24-bit color selector Default: Black Set the text color to display in the specified cell. 5-34 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 249
This setting allows the user to specify a multiplier for the metering parameter value. The multiplier must be in compliance with the 32-bit floating-point format per IEEE 754, otherwise, the input value is represented as per the IEEE standard. For example, 1234.56789 is represented as 1234.567871094, and 9876.54321 as 9876.54296875. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-35...
Page 250
Settings > Product Setup > User-Programmable Self Tests (not shown). When the alarms are triggered, they display with a red background. An alarm is acknowledged by using the arrow keys on the graphical front panel then pressing the ENTER button. 5-36 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 251
Up to 20 characters can be input as the name of each annunciator page. The number of pages depends on the Layout. The name displays for the Tab pushbutton on the graphical front panel. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-37...
Page 252
The background color to display for any triggered cell, for example when an alarm is triggered. ACTUAL (Configure) Range: Configure Default: Configure The Configure button becomes active when the CONTENT field is set to "Actual" or "Mixed." The window specifies the metering data to display. 5-38 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 253
Avoid selecting condition operands that are likely to operate simultaneously but activate different pages, as only one page can be opened at a time. For example, do not select a single-line diagram page for breaker status open and select an annunciator page for a trip alarm. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-39...
The Targets option displays error messages, such as wrong transceiver, similar to event record entries. 5.3.4 Clear relay records SETTINGS PRODUCT SETUP CLEAR RELAY RECORDS CLEAR RELAY CLEAR USER REPORTS: Range: FlexLogic operand RECORDS 5-40 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Selected records can be cleared from user-programmable conditions with FlexLogic operands. Assigning user- programmable pushbuttons to clear specific records is a typical application for these commands. Since the G30 responds to rising edges of the configured FlexLogic operands, they must be asserted for at least 50 ms to take effect.
Page 256
5.3.5.3 Ethernet network topology The G30 has three Ethernet ports. Each Ethernet port must belong to a different network or subnetwork. Configure the IP address and subnet to ensure that each port meets this requirement. Two subnets are different when the bitwise AND operation performed between their respective IP address and mask produces a different result.
Page 257
SCADA is provided through LAN2. P2 and P3 are connected to LAN2, where P2 is the primary channel and P3 is the redundant channel. In this configuration, P3 uses the IP and MAC addresses of P2. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-43...
Page 258
LAN2, to which port 2 (P2) is connected, and communications with SCADA on LAN3, to which port 3 (P3) is connected. There is no redundancy. Figure 5-15: Multiple LANS, no redundancy 5-44 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 259
IP addresses and mask. Configure the network IP and subnet settings before configuring the routing settings. To obtain a list of all port numbers used, for example for audit purposes, contact GE technical support with substantiating information, such as the serial number and order code of your device.
Page 260
2 is performed. The delay in switching back ensures that rebooted switching devices connected to the G30, which signal their ports as active prior to being completely functional, have time to completely initialize themselves and become active. Once port 2 is active again, port 3 returns to standby mode.
Page 261
UR 7 redundancy Failover is selected for redundancy. 5.3.5.6 Parallel Redundancy Protocol (PRP) The G30 is provided with optional PRP capability. This feature is specified as a software option at the time of ordering. See the Order Codes section in chapter 2 for details.
Page 262
Delete the default route by replacing the default gateway with the default value of 127.0.0.1. General conditions to be satisfied by static routes The following rules are validated internally: 5-48 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 263
Port 2 (IP address 10.1.2.2) connects the UR to LAN 10.1.2.0/24 and to the EnerVista software through Router2. Router2 has an interface on 10.1.2.0/24 and the IP address of this interface is 10.1.2.1. The configuration before release 7.10 was as follows: G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-49...
Page 264
SETTINGS PRODUCT SETUP COMMUNICATIONS MODBUS PROTOCOL MODBUS PROTOCOL MODBUS SLAVE Range: 1 to 254 in steps of 1 ADDRESS: 254 MODBUS TCP PORT Range: 0 to 65535 in steps of 1 NUMBER(502): 502 5-50 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 265
0 disables Modbus over TCP/IP, meaning closes the Modbus TCP port. When the port number is changed to 0, the change takes effect when the G30 is restarted. When it is set to 0, use the front panel or serial port to communicate with the relay.
Page 266
DNP UNSOL RESPONSE Range: 0 to 65519 in steps of 1 DEST ADDRESS: 1 DNP CURRENT SCALE Range: 0.001, 0.01. 0.1, 1, 10, 100, 1000, 10000, FACTOR: 1 100000, 1000000, 10000000, 100000000 5-52 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 267
Range: 0 to 32 in steps of 1 CONTROL POINTS: 0 DNP TCP CONNECTION Range: 10 to 7200 s in steps of 1 TIMEOUT: 120 s DNP EVENT TIME BASE: Range: UTC, LOCAL LOCAL G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-53...
Page 268
DNP ADDRESS unique address to each DNP slave. The G30 can specify a maximum of five clients for its DNP connections. These are IP addresses for the controllers to which the G30 can connect. The settings follow. SETTINGS PRODUCT SETUP COMMUNICATIONS DNP PROTOCOL DNP NETWORK CLIENT ADDRESSES ...
Page 269
DNP TCP connection for greater than the time specified by this setting, the connection is aborted by the G30. This frees up the connection to be re-used by a client. For any change to take effect, restart the relay.
Page 270
60870-5-104 point lists must be in one continuous block, any points assigned after the first “Off” point are ignored. 5.3.5.12 IEC 61850 protocol The G30 is provided with optional IEC 61850 communications. This feature is specified as a software option at the time of ordering. See the Order Codes section in chapter 2 for details.
Page 271
The maximum number of simultaneous clients supported by the UR family is five. EnerVista setup for IEC 61850 The EnerVista UR Setup software provides the interface to configure G30 settings for the IEC 61850 protocol. This section describes this interface. The software also supports import/export and merging of IEC 61850 Substation Configuration Language (SCL) files as documented in the UR Family Communications Guide.
Page 272
Figure 5-19: IEC 61850 panel Opening the IEC 61850 window while online causes the UR Setup software to retrieve and import an SCL file from the G30. This System Configuration Description (SCD) file contains all the settings in the UR at the time of the file request, both those that are mapped into the IEC 61850 information model (that is, the "public"...
Page 273
When the Save button is clicked in the online IEC 61850 window, UR Setup software prepares a configured IED description (CID) file containing all the settings of the UR and sends the CID file to the G30. Upon receipt, the G30 checks the CID file for correctness, going out of service, then back into service when the CID file is accepted.
Page 274
Range: status-only, direct-with-normal-security, sbo-with-normal-security Default: sbo-with-normal-security This setting specifies the control service that clients must use to control the TEST MODE FUNCTION of the G30. An "on" control to <LDName>/LLN0.Mod changes TEST MODE FUNCTION to Disabled, an "on-blocked" control changes it to Forcible, and a "test/blocked"...
Page 275
The LLN0 in the Master logical device, which includes setting group, GOOSE and report control blocks, and datasets • LPHD1 — Models common issues for physical devices • GGIO1 — For unmapped FlexLogic operands G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-61...
Page 276
Figure 5-23: Menu for logical node If the insert option is selected, or the edit option is selected for other than the Master logical device, a logical device parameters edit dialog opens. 5-62 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 277
Each logical device inst name is required to be unique within the device, and it cannot be blank. Also, if the corresponding functional ldName setting is blank, the concatenation of the IED name and the logical device G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-63...
Page 278
The UR increments the value of paramRev by one whenever one or multiple setting changes occurs in one Modbus write request by any means (front panel, Modbus, or MMS) other than by SCL file 5-64 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 279
A v7.4 device can send an R-GOOSE message to another v7.4 device when both have R-GOOSE active as the protocol • A v7.4 device can send a GOOSE message to another v7.4 device when both have GOOSE active as the protocol G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-65...
Page 280
Navigate to Settings > Product Setup > Communications > IEC 61850 > GOOSE > TxGOOSE > TxGOOSE1 to access the settings for the first TxGOOSE. The settings and functionality for the others are similar. 5-66 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 281
Range: 0 to 129 VisibleString characters Default: TxGOOSE1 The entered value sets the goID value published in TxGOOSE1 messages, and can be used by subscribers to discriminate the TxGOOSE1 messages from other GOOSE messages. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-67...
Page 282
VID values of 0 and 1 are assigned by IEEE 802.1Q to other functions and are not to be used for GOOSE. 5-68 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 283
Also, Port 3 configuration in the CID file is ignored. The Port 3 ConnectedAP elements has no meaning, as ports 2 and 3 use the port 2 MAC address, IP address, and mask. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-69...
Page 284
(test field in edition 1.0 messages) are accepted only when the UR Test Mode Function setting is set to Forcible or Isolated. RxGOOSE messages can be received through any UR Ethernet port. 5-70 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 285
RxGOOSE1 messages. An entered address of zero disables RxGOOSE1. If the publisher is a UR series 7.3x device, the setting needs to match the value of the publisher’s TxGOOSE DST MAC setting. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-71...
Page 286
<GoCBName> is the name of the publishing control block. The G30 translates the ACSI format required for this setting to the MMS format used in GOOSE messages: <LDName>/LLN0$GO$<GoCBName> If the publisher is a UR 7.3x or 7.40 series device, <LDName> is the value of the publisher's Master functional ldName setting if that setting is not empty, otherwise it is the value of the publisher's IED NAME suffixed with "Master".
Page 287
7.40 UR Setup RxGOOSE Inputs pages. In this case the Member setting displays as the product-related name used by the publishing IED of the data object or data attribute, in standard SCSM format (e.g. Publisher1LD1/LLN0$ST$Off$stVal). G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-73...
Page 288
(supported in version 7.40 and later). When the file format is SCD, the system lists all IEDs inside the SCD file and lets the user select the ones to add. The figure shows a selection being made by importing a CID file using the Add IED function. 5-74 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 289
This setting selects the logic state for the RxGOOSE Boolean1 FlexLogic operand if the UR has just completed startup and the selected RxGOOSE has not yet received a message, or the selected RxGOOSE has lost its connectivity with the publisher. The following choices are available: G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-75...
Page 290
Range: None, RxGOOSE1, RxGOOSE2, and so on Default: None This setting selects the GOOSE message containing the value that drives the RxGOOSE DPS1 FlexLogic operand. If set to None, the RxGOOSE DPS1 FlexLogic operand assumes its default state. 5-76 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 291
(supported in version 7.40 and later). When the file format is SCD, the system lists all IEDs inside the SCD file and lets the user select the ones to add. Figure 5-31: RxGOOSE Analog Inputs panel There are 32 RxGOOSE analog inputs. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-77...
Page 292
Range: 0.000 to 1000000000.000 in steps of 0.001 Default: 1.000 This setting specifies the per-unit base value for other G30 features to use with the RxGOOSE Analog1 operand. A FlexElement for instance subtracts two quantities after converting their values to integers rescaled to a common base, the common base being the largest of the base values of the two quantities.
Page 293
RptEna attribute is false. Buffered and unbuffered reports Navigate to Settings > Product Setup > Communications > IEC 61850 > Reports > Buffered Reports or Unbuffered Reports. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-79...
Page 294
Also, the control block can be configured to send integrity reports containing the present value of all members either on demand from the client or periodically. A TCP handshaking mechanism causes messages that are not read and acknowledged by the client to be retransmitted. 5-80 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 295
Control blocks and data sets can be pre-configured by sending the G30 a CID file. See the UR Family Communications Guide for details. EnerVista UR Setup also can be used to select the data set members and to pre-configure the control blocks.
Page 296
This setting selects the data set whose members' status is reported in Unbuffered Report1 messages using the UR Setup software designator for the data set. The IEC 61850 name of the data sets are configured in the Datasets panel, as described later. 5-82 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 298
The DataSet name is not copied or pasted. In short, use this feature to copy a DataSet Member setting and paste it into another Member setting, a text file, or Word, as examples. 5-84 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 299
Select the member from the drop-down list. Or right-click an entry to copy, paste, delete, or insert. Product setup Navigate to Settings > Product Setup > Communications > IEC 61850 > Product Setup. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-85...
Page 300
Deadband parameters of measured values related to the Energy metering are configured here. Real Time Clock Navigate to Settings > Product Setup > Communications > IEC 61850 > Product Setup > Real Time Clock. 5-86 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 301
The analog value that each deadband setting applies is usually obvious from the name of the setting. However, a tabulation of the analog values and their associated deadband setting can be found in the UR Family Communications Guide. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-87...
Page 302
Auxiliary voltage — 275 x auxiliary VT ration setting • Power (real, reactive, apparent, 3-phase, and 1-phase) — 4 × phase CT primary setting × 1.5 × VT Secondary setting × VT ratio setting 5-88 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 303
While the selected operand is asserted, Bkr0XCBR1.Loc.stVal is true and IEC 61850 commands to BkrCSWI1.Pos and Bkr0XCBR1.Pos are not accepted, and a Negative Response (-Rsp) is issued with the REASON CODE of Blocked-by- switching-hierarchy. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-89...
Page 304
Bkr0XCBR1.BlkOpn.ctlVal signal on the Breaker Control Logic (Sheet 1 of 2) diagram in the Settings > System Setup section later. This signal when true blocks breaker 1 trip control while the operand selected by setting XCBR1 ST.LOC OPERAND is not active. 5-90 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 305
Navigate to Settings > Product Setup > Communications > IEC 61850 > System Setup > Switches > Switch 1 to access the settings that configure the IEC 61850 protocol interface with the first disconnect switch control and status monitoring element. The settings and functionality for the others are similar. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-91...
Page 306
> System Setup section later. These signals force a disconnect switch trip or close control while the operand selected by setting XSWI1 ST.LOC OPERAND is not active. "sbo" here is select-before-operate. Enhanced security means that the G30 reports to the client the disconnect switch 1 position the end of the command sequence.
Page 307
SelectEditSG. The setting related to these IEC 61850 commands are described here. Navigate to Settings > Product Setup > Communications > IEC 61850 > Control Elements > Setting Groups to access the setting that configures the IEC 61850 setting group commands. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-93...
Page 308
Navigate to Settings > Product Setup > Communications > IEC 61850 > Settings for Commands to access the settings that configure the IEC 61850 protocol interface for record clear commands. Figure 5-43: Commands panel 5-94 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 309
This setting selects the control model clients must use to successfully control the command CLEAR FAULT REPORTS. "sbo" here is select-before-operate. Enhanced security means that the G30 reports to the client the breaker 1 position at the end of the command sequence.
Page 310
Navigate to Settings > Product Setup > Communications > IEC 61850 > GGIO > GGIO2 to access the settings that configure the IEC 61850 protocol interface for Virtual Input commands. Figure 5-45: GGIO2 panel 5-96 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 311
<LDName>/GGIO4.AnIn01.instMag.f. The value of the FlexAnalog operand is converted automatically to the format and scaling required by the standard, that is to say primary amperes, primary volts, and so on. See Appendix A for a list of FlexAnalog operands. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-97...
Page 312
File transfer by IEC 61850 The G30 supports file transfer by IEC 61850. The approach is as follows, using the SISCO AX-S4 61850 client software as an example. In the AX-S4 61850 Explorer window, click the Tools menu and access the SISCO File Transfer Utility.
Page 313
NUMBER(80): 80 The G30 contains an embedded web server and can display pages in a web browser. The web pages are organized as a series of menus that can be accessed starting at the G30 “Main Menu.” Web pages are read-only and are available showing DNP and IEC 60870-5-104 points lists, Modbus registers, event records, fault reports, and so on.
Page 314
NUMBER: 0 The Trivial File Transfer Protocol (TFTP) can be used to transfer files from the G30 over a network. The G30 operates as a TFTP server. TFTP client software is available from various sources, including Microsoft Windows NT. The dir.txt file obtained from the G30 contains a list and description of all available files, for example event records and oscillography.
Page 315
COMMUNICATIONS PROTOCOL connected to a maximum of two masters (usually either an RTU or a SCADA master station). Since the G30 maintains two sets of IEC 60870-5-104 data change buffers, ideally no more than two masters actively communicate with the G30 at one time.
Page 316
CHAPTER 5: SETTINGS The G30 can specify a maximum of five clients for its IEC 104 connections. These are IP addresses for the controllers to which the G30 can connect. A maximum of two simultaneous connections are supported at any given time.
Page 317
EXCH 1 DATA ITEM 1 to 20/50 from the G30 memory map can be configured to be included in an EGD exchange. The settings are the starting Modbus register address for the data item in decimal format. See the Modbus memory map in the UR Series Communications Guide for details.
Page 318
PTP, or SNTP, its time is overwritten by these three sources, if any of them is active. If the synchronization timeout occurs and none of IRIG-B, PTP, or SNTP is active, the G30 sets the invalid bit in the time stamp of a time-tagged message.
Page 319
Spontaneous transmission occurs as a response to cyclic Class 2 requests. If the G30 wants to transmit Class 1 data at that time, it demands access for Class 1 data transmission (ACD=1 in the control field of the response).
Page 320
FlexAnalog operands. The measurands sent are voltage, current, power, power factor, and frequency. If any other FlexAnalog is chosen, the G30 sends 0 instead of its value. Note that the power is transmitted in KW, not W. Measurands are transmitted as ASDU 3 or ASDU 9 (type identification value set to measurands I, respectively measurands II).
Page 321
Range: Virtual input COMMAND 31 OFF: Range: Virtual input Commands are received as General Command (Type Identification 20). The user can configure the action to perform when an ASDU command comes. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-107...
PRODUCT SETUP CHAPTER 5: SETTINGS A list of available mappings is provided on the G30. This includes 64 virtual inputs (see the following table). The ON and OFF for the same ASDU command can be mapped to different virtual inputs.
Setup for IRIG-B is illustrated in the Installation chapter. For the Other protocols, whenever a time synchronization message is received through any of the active protocols, the G30 clock updates. However, given that IEC 60870-5-103, IEC 60870-5-104, Modbus, and DNP are low-accuracy time synchronization methods, avoid their use for synchronization when better accuracy time protocols, such as IRIG-B and PTP, are active in the system.
Page 324
See the Order Codes section in chapter 2 for details. The G30 supports the Precision Time Protocol (PTP) specified in IEEE Std 1588 2008 using the Power Profile (PP) specified in IEEE Std C37.238 2011. This enables the relay to synchronize to the international time standard over an Ethernet network that implements PP.
Page 325
When a clock on start-up discovers that it is “better” than the present grandmaster, it assumes the grandmaster role and the previous grandmaster reverts to slave. The G30 qualification mechanism accepts a potential master clock as a new grandmaster, when in a four-second interval it has received three announce messages from it, all better than the present grandmaster clock and better than any other announce in this interval.
Page 326
G30 clock is closely synchronized with the SNTP/ NTP server. It takes up to two minutes for the G30 to signal an SNTP self-test error if the server is offline.
2:00 The G30 maintains two times: local time and Universal Coordinated Time (UTC). Local time can be provided by IRIG-B signals. UTC time is provided by SNTP servers. The real-time clock (RTC) and time stamps reported in historical records and communication protocols can be incorrect if the Local Time settings are not configured properly.
The user programmable record contains the following information: the user-programmed relay name, detailed firmware revision (x.xx, for example) and relay model (G30), the date and time of trigger, the name of pre-fault trigger (a specific FlexLogic operand), the name of fault trigger (a specific FlexLogic operand), the active setting group at pre-fault trigger, the active setting group at fault trigger, pre-fault values of all programmed analog channels (one cycle before pre-fault trigger), and fault values of all programmed analog channels (at the fault trigger).
Page 329
Parameters set to “Off” are ignored. To populate quickly the rows in the Offline Window, use Ctrl C/V to copy/paste, or click then double-click a row to display a quick selection window. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-115...
DATA LOGGER DATA LOGGER MODE: Range: Continuous, Trigger Continuous DATA LOGGER TRIGGER: Range: FlexLogic operand DATA LOGGER RATE: Range: 15 to 3600000 ms in steps of 1 60000 msec 5-116 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 331
Analog Input hardware modules installed. Upon startup, the relay automatically prepares the parameter list. A list of all possible analog metering actual value parameters is shown in G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-117...
Page 332
All 62 LEDs on the relay are illuminated. This is a quick test to verify if any of the LEDs is “burned.” This stage lasts as long as the control input is on, up to a maximum of one minute. After one minute, the test ends. 5-118 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 333
The test responds to the position and rising edges of the control input defined by the LED TEST CONTROL setting. The control pulses must last at least 250 ms to take effect. The following diagram explains how the test is executed. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-119...
Page 334
2. When stage 2 is completed, stage 3 starts automatically. The test can be cancelled at any time by pressing the pushbutton. 5-120 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
LED 19 operand LED 8 operand LED 20 operand LED 9 operand LED 21 operand LED 10 operand LED 22 operand LED 11 operand LED 23 operand LED 12 operand LED 24 operand G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-121...
The location of the control pushbuttons are shown in the following figures. Figure 5-51: Control pushbuttons (enhanced front panel) An additional four control pushbuttons are included on the standard front panel when the G30 is ordered with the 12 user- programmable pushbutton option.
Range: up to 20 alphanumeric characters USER PB 1 PUSHBTN 1 ON TEXT: Range: up to 20 alphanumeric characters PUSHBTN 1 OFF TEXT: Range: up to 20 alphanumeric characters 5-124 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 339
EVENTS: Disabled The G30 is provided with this optional feature, specified as an option at the time of ordering. Using the order code for your device, see the order codes in chapter 2 for details. User-programmable pushbuttons provide an easy and error-free method of entering digital state (on, off) information. The number depends on the front panel ordered.
Page 340
PUSHBTN 1 SET interface. The state of each pushbutton is stored in non-volatile memory and maintained through a loss of control power. 5-126 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 341
“Self-reset” as the pushbutton operand status is implied to be “Off” upon its PUSHBUTTON 1 FUNCTION release. The length of the “Off” message is configured with the PRODUCT SETUP DISPLAY PROPERTIES FLASH MESSAGE G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-127...
Page 342
10 seconds. — If this setting is enabled, each user-programmable pushbutton state change is logged as an PUSHBUTTON 1 EVENTS event into the event recorder. The figures show the user-programmable pushbutton logic. 5-128 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
The state bits can be read out in the “Flex States” register array beginning at Modbus address 0900h. Sixteen states are packed into each register, with the lowest-numbered state in the lowest-order bit. Sixteen registers accommodate the 256 state bits. 5-130 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
When this type of entry occurs, the sub-menus are automatically configured with the proper content—this content can be edited subsequently. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-131...
Page 346
If the parameters for the top line and the bottom line items have the same units, then the unit is displayed on the bottom line only. The units are only displayed on both lines if the units specified both the top and bottom line items are different. 5-132 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
DIRECT OUTPUT DEVICE ID messages. All UR-series IEDs in a ring need to have unique numbers assigned. The IED ID is used to identify the sender of the direct input and output message. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-133...
Page 348
DIRECT I/O DATA RATE setting applies to a G30 with dual-channel communication cards and allows crossing DIRECT I/O CHANNEL CROSSOVER over messages from channel 1 to channel 2. This places all UR-series IEDs into one direct input and output network regardless of the physical media of the two communication channels.
Page 349
DIRECT I/O CH1 RING CONFIGURATION: “Yes” DIRECT I/O CH2 RING CONFIGURATION: “Yes” For UR-series IED 2: DIRECT OUTPUT DEVICE ID: “2” DIRECT I/O CH1 RING CONFIGURATION: “Yes” DIRECT I/O CH2 RING CONFIGURATION: “Yes” For UR-series IED 3: G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-135...
Page 350
Figure 5-62: Three-terminal line application A permissive pilot-aided scheme can be implemented in a two-ring configuration, shown as follows (IEDs 1 and 2 constitute a first ring, while IEDs 2 and 3 constitute a second ring). 5-136 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 351
In this application, apply the following settings. For UR-series IED 1: DIRECT OUTPUT DEVICE ID: “1” DIRECT I/O CH1 RING CONFIGURATION: “Yes” DIRECT I/O CH2 RING CONFIGURATION: “Yes” For UR-series IED 2: G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-137...
Page 352
EVENTS: Disabled The G30 checks integrity of the incoming direct input and output messages using a 32-bit CRC. The CRC alarm function is available for monitoring the communication medium noise by tracking the rate of messages failing the CRC check. The monitoring function counts all incoming messages, including messages that failed the CRC check.
EVENTS: Disabled The G30 checks integrity of the direct input and output communication ring by counting unreturned messages. In the ring configuration, all messages originating at a given device should return within a pre-defined period of time. The unreturned messages alarm function is available for monitoring the integrity of the communication ring by tracking the rate of unreturned messages.
5.4 Remote resources 5.4.1 Remote resources configuration When the G30 is ordered with a process card module as a part of HardFiber system, an additional Remote Resources menu tree is available in the EnerVista software to allow configuration of the HardFiber system.
Page 355
Bricks. Remote resources settings configure the point-to-point connection between specific fiber optic ports on the G30 process card and specific Brick. The relay is then configured to measure specific currents, voltages and contact inputs from those Bricks, and to control specific outputs.
The same rule applies for current sums from CTs with different secondary taps (5 A and 1 A). 5.5.1.2 Voltage banks SETTINGS SYSTEM SETUP AC INPUTS VOLTAGE BANK F5(M5) VOLTAGE BANK F5 PHASE VT F5 Range: Wye, Delta CONNECTION: Wye 5-142 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
PHASE ROTATION sequence, either ABC or ACB. CT and VT inputs on the relay, labelled as A, B, and C, must be connected to system phases A, B, and C for correct operation. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-143...
FREQUENCY TRACKING frequency applications. The frequency tracking feature functions only when the G30 is in the “Programmed” mode. If the G30 is “Not Programmed,” then metering values are available but can exhibit significant errors. Systems with an ACB phase sequence require special consideration. See the Phase Relationships of Three-phase Transformers section of chapter 5.
Page 359
CT wiring problem. A disturbance detector is provided for each source. The 50DD function responds to the changes in magnitude of the sequence currents. The disturbance detector logic is as follows. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-145...
Page 360
8 CTs 4 CTs, 4 VTs 4 CTs, 4 VTs C60, D60, G30, G60, L30, L90, M60, T60 not applicable This configuration can be used on a two-winding transformer, with one winding connected into a breaker-and-a-half system. The following figure shows the arrangement of sources used to provide the functions required in this application, and the CT/VT inputs that are used to provide the data.
SETTINGS SYSTEM SETUP TRANSFORMER TRANSFORMER GENERAL See below WINDING 1 See page 5-149 WINDING 2 THERMAL INPUTS See page 5-157 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-147...
Page 362
CT primary by SQRT 3. This compensates for the increase of SQRT 3 caused by the Delta CT connection. Therefore, the Actual Value of current and power cannot be used for measurements in this case. Figure 5-68: Wye winding and Delta CT connection 5-148 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 363
(shown when viewed Winding is not Winding 1) The G30 is provided with this optional feature, specified as an option at the time of ordering. Using the order code for your device, see the order codes in chapter 2 for details.
Page 364
In this standard, the arbitrary labeling of the windings is shown as I, II, and III. This standard states that the phase relationships are established for a condition where a source phase sequence of I-II-III is connected to transformer windings labeled I, II, and III respectively. 5-150 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 365
The following example shows why this happens, using a transformer described in IEC nomenclature as a type “Yd1” or in GE Multilin nomenclature as a “Y/d30.” The example shows the physical connections within the transformer that produce a phase angle in the delta winding that lag the respective wye winding by 30°.
Page 366
Interposing CTs or tapped relay windings were used to minimize this error. The G30 automatically corrects for CT mismatch errors. All currents are magnitude compensated to be in units of the CTs of one winding before the calculation of differential and restraint quantities.
Page 367
In this example, the unit CT is 1500:5 on winding 2. Magnitude compensation factors (M) are the scaling values by which each winding current is multiplied to refer it to the reference winding. The G30 calculates magnitude compensation factors for each winding as follows: Eq. 5-11 In our example, the magnitude compensation factors are calculated as follows: Eq.
Page 368
The G30 performs this phase angle compensation and zero sequence removal automatically, based on the settings entered for the transformer. All CTs are connected Wye (polarity markings pointing away from the transformer). All currents are phase and zero sequence compensated internally before the calculation of differential and restraint quantities.
Page 369
CHAPTER 5: SETTINGS SYSTEM SETUP Table 5-19: Phase and zero sequence compensation for typical values of Φ comp G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-155...
Page 370
[w] = magnitude, phase, and zero-sequence compensated winding w phase currents M [w] = magnitude compensation factor for winding w (see previous sections) [w], I [w], and I [w] = phase and zero sequence compensated winding w phase currents (see earlier) 5-156 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 371
Range: –60 to 60°C in steps of 1 –30°C MARCH AVERAGE: Range: –60 to 60°C in steps of 1 –10°C DECEMBER AVERAGE: Range: –60 to 60°C in steps of 1 –10°C G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-157...
Range: 0.000 to 65.535 s in steps of 0.001 TIME: 0.000 s BREAKER 1 OPEN Range: 0.000 to 65.535 s in steps of 0.001 SEAL-IN: 0.000 s BREAKER 1 OUT OF SV: Range: FlexLogic operand 5-158 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 373
— If the mode is selected as three-pole, this setting has no function. If the mode is selected as single- BREAKER 1 ΦB OPENED pole, this input is used to track the breaker phase B opened position as outlined for phase A. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-159...
Page 374
If this setting is set to Off, the racked status is not considered. 5-160 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 375
CHAPTER 5: SETTINGS SYSTEM SETUP Figure 5-72: Dual breaker control logic (Sheet 1 of 3) G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-161...
Page 376
SYSTEM SETUP CHAPTER 5: SETTINGS Figure 5-73: Dual breaker control logic (Sheet 2 of 3) 5-162 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 378
— This setting selects “3-Pole” mode, where disconnect switch poles have a single common auxiliary SWITCH 1 MODE switch, or “1-Pole” mode where each disconnect switch pole has its own auxiliary switch. 5-164 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 379
— This setting specifies the delay interval during which a disagreement of status among the pole SWITCH 1 ALARM DELAY position tracking operands do not declare a pole disagreement. This allows for non-simultaneous operation of the poles. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-165...
Page 380
CHAPTER 5: SETTINGS IEC 61850 functionality is permitted when the G30 is in “Programmed” mode and not in local control mode. The switch element has direct hard-coded connections to the IEC 61850 model as shown in the logic diagrams. This allows remote open/close operation of each switch, using either CSWI or XSWI IEC 61850 logical nodes.
Page 381
CHAPTER 5: SETTINGS SYSTEM SETUP Figure 5-76: Disconnect switch control status logic (sheet 2 of 3) G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-167...
FlexCurve, enter the reset and operate times (using the keys) for each selected pickup point (using the VALUE up/down keys) for the required protection curve (A, B, C, or D). MESSAGE 5-168 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 383
The recloser curve configuration window shown here appears when the Initialize From setting in the EnerVista software is set to “Recloser Curve” and the Initialize FlexCurve button is clicked. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-169...
Page 384
MRT and from then onwards the operating time remains at 200 ms. Figure 5-79: Composite recloser curve with HCT disabled With the HCT feature enabled, the operating time reduces to 30 ms for pickup multiples exceeding eight times pickup. 5-170 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 385
EnerVista software generates an error message and discards the proposed changes. 5.5.7.5 Standard recloser curves The following graphs display standard recloser curves available for the G30. Figure 5-81: Recloser curves GE101 to GE106 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 386
SYSTEM SETUP CHAPTER 5: SETTINGS Figure 5-82: Recloser curves GE113, GE120, GE138, and GE142 Figure 5-83: Recloser curves GE134, GE137, GE140, GE151, and GE201 5-172 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 387
CHAPTER 5: SETTINGS SYSTEM SETUP Figure 5-84: Recloser curves GE131, GE141, GE152, and GE200 Figure 5-85: Recloser curves GE133, GE161, GE162, GE163, GE164, and GE165 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-173...
Page 388
SYSTEM SETUP CHAPTER 5: SETTINGS Figure 5-86: Recloser curves GE116, GE117, GE118, GE132, GE136, and GE139 Figure 5-87: Recloser curves GE107, GE111, GE112, GE114, GE115, GE121, and GE122 5-174 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
FlexLogic. In general, the system receives analog and digital inputs that it uses to produce analog and digital outputs. The figure shows major subsystems of a generic UR-series relay involved in this process. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-175...
Page 390
Figure 5-89: UR architecture overview The states of all digital signals used in the G30 are represented by flags (or FlexLogic operands, which are described later in this section). A digital “1” is represented by a set flag. Any external contact change-of-state can be used to block an element from operating, as an input to a control feature in a FlexLogic equation, or to operate a contact output.
Page 391
The following table lists the operands available for the relay. The operands can be viewed online by entering the IP address of the relay in a web browser and accessing the Device Information Menu. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-177...
Page 392
Breaker arcing current 2 has dropped out BKR ARC 2 MAX OP Breaker arcing current 2 max interrupting current has operated BKR ARC 2 MAX DPO Breaker arcing current 2 max interrupting current has dropped out 5-178 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 393
DIR POWER 1 DPO The directional power element has dropped out DIR POWER 1 OP The directional power element has operated DIR POWER 2 Same set of operands as DIR POWER 1 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-179...
Page 394
NEUTRAL TOC1 PKP Neutral time overcurrent 1 has picked up Neutral time NEUTRAL TOC1 OP Neutral time overcurrent 1 has operated overcurrent NEUTRAL TOC1 DPO Neutral time overcurrent 1 has dropped out 5-180 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 395
Phase A of phase undervoltage 1 has dropped out PHASE UV1 DPO B Phase B of phase undervoltage 1 has dropped out PHASE UV1 DPO C Phase C of phase undervoltage 1 has dropped out G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-181...
Page 396
Source 1 VT neutral wire open detected. When the VT is connected in Delta, do not enable this function because there is no neutral wire for Delta connected VT. SRC2 VT FUSE FAIL to SRC4 Same set of operands as shown for SRC1 VT FF 5-182 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 397
Same set of operands as shown for THERMAL PROT 1 ELEMENT: TRIP BUS 1 PKP Asserted when the trip bus 1 element picks up Trip bus TRIP BUS 1 OP Asserted when the trip bus 1 element operates G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-183...
Page 398
(does not appear unless ordered) Cont Op 1 VOff Cont Op 2 VOff (does not appear unless ordered) ↓ ↓ Cont Op 72 VOff (does not appear unless ordered) 5-184 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 399
Asserted when a neutral or ground element involved and to turn Event Cause LED 9 on by default LED INDICATORS: LED TEST IN PROGRESS An LED test has been initiated and has not finished LED test G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-185...
Page 400
RESET ANCTR OP(OPRD) Reset operand (assigned in INPUTS/OUTPUTS RESETTING ANNUNCIATOR menu) source of the reset annunciator command RESET ANCTR OP(MNUL) Reset manual (pushbutton or EnerVista software) source of the reset annunciator command 5-186 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 401
2 to 16 any input is ‘1’ 2 to 16 all inputs are ‘1’ 2 to 16 all inputs are ‘0’ NAND 2 to 16 any input is ‘0’ only one input is ‘1’ G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-187...
A timer operator (for example, "TIMER 1") or virtual output assignment (for example, " = Virt Op 1") can be used once only. If this rule is broken, a syntax error is declared. 5.6.3 FlexLogic evaluation Each equation is evaluated in the ascending order in which the parameters have been entered. 5-188 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
4, which is programmed in the contact output section to operate relay H1 (that is, contact output H1). Therefore, the required logic can be implemented with two FlexLogic equations with outputs of virtual output 3 and virtual output 4, shown as follows. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-189...
Page 404
It is generally easier to start at the output end of the equation and work back towards the input, as shown in the following steps. It is also recommended 5-190 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 405
It is now possible to check that this selection of parameters produces the required logic by converting the set of parameters into a logic diagram. The result of this process is shown in the figure, which is compared to the logic for virtual output 3 diagram as a check. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-191...
Page 406
Now check that the selection of parameters produce the required logic by converting the set of parameters into a logic diagram. The result is shown in the figure, which is compared to the logic for virtual output 4 diagram as a check. 5-192 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 407
Always test the logic after it is loaded into the relay, in the same way as has been used in the past. Testing can be simplified by placing an "END" operator within the overall set of FlexLogic equations. The equations are evaluated up G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-193...
Range: Off, any analog actual value parameter FLEXELEMENT 1 INPUT Range: SIGNED, ABSOLUTE MODE: SIGNED FLEXELEMENT 1 COMP Range: LEVEL, DELTA MODE: LEVEL FLEXELEMENT 1 Range: OVER, UNDER DIRECTION: OVER 5-194 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 409
— This setting specifies the first (non-inverted) input to the FlexElement. Zero is assumed as the input if FLEXELEMENT 1 +IN this setting is set to “Off.” For proper operation of the element, at least one input must be selected. Otherwise, the element does not assert its output operands. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-195...
Page 410
Figure 5-98: FlexElement direction, pickup, and hysteresis In conjunction with the setting, the element can be programmed to provide two extra FLEXELEMENT 1 INPUT MODE characteristics, as shown in the following figure. 5-196 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 411
(Brk X Arc Amp A, B, and C) DCmA BASE = maximum value of the DCMA INPUT MAX setting for the two transducers configured under the +IN and –IN inputs DELTA TIME BASE = 1 µs G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-197...
The active setting group can be preset or selected in the menu (see the Control Elements section SETTING GROUPS later in this chapter). See also the Introduction to Elements section at the beginning of this chapter. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-199...
AGING FACTOR See page 5-206 LOSS OF LIFE See page 5-207 This menu contains the settings for the transformer differential elements and the transformer thermal elements. 5-200 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 415
> K, where PKP represents a percent differential pickup setting and K is a restraint factor defined by the relays settings Slope 1, Slope 2, and a transition area between breakpoint 1 and breakpoint 2 settings. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-201...
Page 416
• CT saturation To provide higher security during CT saturation conditions and to ease CT requirements, the G30 incorporates a dedicated CT saturation detection mechanism. The G30 CT saturation detector can detect saturation happening after approximately 3 ms from fault inception. In case CT saturation is detected, the percent differential is blocked instantly and relies further on the directional element in case fault evolved from external to internal to operate without any delays.
Page 417
2nd harmonic and the fundamental frequency component. The traditional 2nd harmonic restraint responds to the ratio of magnitudes of the 2nd harmonic and fundamental frequency components. If low second harmonic ratios during magnetizing inrush conditions are not expected, set the relay to a traditional way of restraining. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-203...
Page 418
The relay produces three FlexLogic operands that can be used for testing or for special applications, such as building custom logic (1-out-of-3) or supervising some protection functions (ground time overcurrent, for example) from the 2nd harmonic inhibit. 5-204 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 419
CHAPTER 5: SETTINGS GROUPED ELEMENTS Figure 5-103: Percent differential logic G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-205...
Page 420
The Aging Factor element detects transformer aging in per-unit normal insulation aging. The element can be set to alarm or trip whenever the computed aging factor is greater than the user-defined pickup setting for the specified time delay. 5-206 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 421
— Enter the expended life, in hours, required for operation of the element. Set this setting above the LOSS OF LIFE PICKUP total transformer life set as a reference based on nominal loading conditions and a 30°C ambient temperature, as outlined in the IEEE standards. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-207...
DIRECTIONAL 1 5.7.4.2 Inverse TOC curve characteristics The inverse time overcurrent curves used by the time overcurrent elements are the IEEE, IEC, GE Type IAC, and I t standard curve shapes. This allows for simplified coordination with downstream devices.
Page 425
A to E = constants defined in the table = characteristic constant defined in the table = reset time in seconds (assuming energy capacity is 100% and RESET is “Timed”) RESET Table 5-31: GE type IAC inverse time curve constants IAC curve shape IAC Extreme Inverse 0.0040 0.6379...
Page 426
GROUPED ELEMENTS CHAPTER 5: SETTINGS Table 5-32: GE type IAC curve trip times Multiplier Current ( I / I pickup (TDM) 10.0 IAC Extremely Inverse 1.699 0.749 0.303 0.178 0.123 0.093 0.074 0.062 0.053 0.046 3.398 1.498 0.606 0.356 0.246 0.186...
Page 427
T = Operate Time (in seconds) TDM = Multiplier setting I = Input Current = Pickup Current setting pickup = Reset Time in seconds (assuming energy capacity is 100% and RESET: Timed) RESET G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-213...
Page 428
GROUPED ELEMENTS CHAPTER 5: SETTINGS Recloser curves The G30 uses the FlexCurve feature to facilitate programming of 41 recloser curves. See the FlexCurves settings section earlier in this chapter for details. 5.7.4.3 Phase time overcurrent (ANSI 51PV, IEC PTOC) SETTINGS GROUPED ELEMENTS SETTING GROUP 1(6) PHASE CURRENT PHASE TOC1(2) ...
Page 429
— Selects the signal source for the phase time overcurrent protection element. SIGNAL SOURCE — Selects how phase current input quantities are interpreted by the G30. Inputs can be selected as fundamental INPUT phasor magnitudes or total waveform RMS magnitudes as required by the application.
Page 431
Range: 0.004 to 3.000 pu in steps of 0.001 THRESHOLD: 0.700 pu PHASE DIR 1 BLOCK Range: No, Yes WHEN V MEM EXP: No PHASE DIR 1 Range: Self-reset, Latched, Disabled TARGET: Self-reset G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-217...
Page 432
(phase current) and the polarizing signal (the line voltage, shifted in the leading direction by the characteristic angle, ECA). The table shows the operating and polarizing signals used for phase directional control. 5-218 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 433
When set to "No," the directional element allows tripping of phase overcurrent elements under directional control. — This setting enables and disables the logging of phase directional overcurrent events in the PHASE DIR 1 EVENTS sequence of events recorder. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-219...
NEUTRAL TOC 2 NEUTRAL IOC 1 See page 5-222 NEUTRAL See page 5-223 DIRECTIONAL OC1 NEUTRAL DIRECTIONAL OC2 5-220 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 435
— This setting selects the signal source for the neutral time overcurrent protection element. NEUTRAL TOC1 SIGNAL SOURCE — This setting selects how neutral current input quantities are interpreted by the G30. Inputs can be NEUTRAL TOC1 INPUT selected as fundamental phasor magnitudes or total waveform RMS magnitudes as required by the application.
Page 436
The positive-sequence restraint allows for more sensitive settings by counterbalancing spurious zero-sequence currents resulting from: • System unbalances under heavy load conditions • Transformation errors of current transformers (CTs) during double-line and three-phase faults • Switch-off transients during double-line and three-phase faults 5-222 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 437
VOLT: Calculated V0 NEUTRAL DIR OC1 OP Range: Calculated 3I0, Measured IG CURR: Calculated 3I0 NEUTRAL DIR OC1 POS- Range: 0.000 to 0.500 in steps of 0.001 SEQ RESTRAINT: 0.063 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-223...
Page 438
The following tables define the neutral directional overcurrent element. V_0 is the zero-sequence voltage, I_0 is the zero-sequence current, ECA is the element characteristic angle, and IG is the ground current. 5-224 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 439
REV LA = 80° (reverse limit angle = the ± angular limit with the ECA for operation) Take the bias into account when using the neutral directional overcurrent element to directionalize other protection elements. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-225...
Page 440
For example, if using an autotransformer neutral current as a polarizing source, ensure that a reversal of the ground current does not occur for a high-side fault. Assume that the 5-226 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 441
When selecting this setting, keep in mind that the design uses a positive-sequence restraint technique for the “Calculated 3I0” mode of operation. Proper application of this element requires that the operating current and the polarizing voltage (or current) be measured from the same side of the transformer. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-227...
RESTRICTED GROUND FAULT 4 The G30 relay contains one Ground Time Overcurrent, one Ground Instantaneous Overcurrent, and four Restricted Ground Fault elements. See the Inverse TOC Curve Characteristics section earlier for information. 5-228 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 443
— This setting selects the signal source for the ground time overcurrent protection element. GROUND TOC1 SIGNAL SOURCE — This setting selects how ground current input quantities are interpreted by the G30. Inputs can be GROUND TOC1 INPUT selected as fundamental phasor magnitudes or total waveform RMS magnitudes as required by the application.
Page 444
0.02 to 46 times the CT rating. This channel can be equipped with a standard or sensitive input. The conversion range of a sensitive channel is from 0.002 to 4.6 times the CT rating. 5-230 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 445
Application of the restricted ground fault protection extends the coverage towards the neutral point (see the following figure). G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-231...
Page 446
Even with the improved definition of the restraining signal, the breaker-and-a-half application of the restricted ground fault must be approached with care, and is not recommended unless the settings are carefully selected to avoid maloperation due to CT saturation. 5-232 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 447
(Igr(k)) does not reduce instantly but keeps decaying decreasing its value by 50% each 15.5 power system cycles. Having the differential and restraining signals developed, the element applies a single slope differential characteristic with a minimum pickup as shown in the following logic diagram. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-233...
Page 448
Given the following inputs: IA = 1.10 pu ∠0°, IB = 1.0 pu ∠–120°, IC = 1.0 pu ∠120°, and IG = 0.05 pu ∠0° The relay calculates the following values: I_0 = 0.033 pu ∠0°, I_2 = 0.033 pu ∠0°, and I_1 = 1.033 pu ∠0° 5-234 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
NEG SEQ DIR OC1 FWD Range: 0 to 90° Lag in steps of 1 ECA: 75° Lag NEG SEQ DIR OC1 FWD Range: 40 to 90° in steps of 1 LIMIT ANGLE: 90° G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-235...
Page 450
CT errors, since the current is low. The operating quantity depends on the way the test currents are injected into the G30. For single phase injection •...
Page 451
(see the Application of Settings chapter for information on how to calculate this setting). In regular applications, the offset impedance ensures G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-237...
Page 452
When NEG SEQ DIR OC1 TYPE selecting this setting, keep in mind that the design uses a positive-sequence restraint technique. Figure 5-122: Negative-sequence directional OC1 logic 5-238 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
This is set to prevent false trips for faults that would be cleared normally by system protections. — The maximum operate time of the stage 1 element. This setting can be applied to limit the GEN UNBAL STG1 TMAX maximum tripping time for low level unbalances. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-239...
Page 454
— The minimum operate time of the stage 2 element. This is set to prevent nuisance alarms GEN UNBAL STG2 PKP DELAY during system faults. Figure 5-123: Generator unbalance inverse time curves Figure 5-124: Generator unbalance logic 5-240 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
The split phase element allows a separate pickup setting to be applied for each phase. Additionally, the pickup can be biased by the load current (slope characteristic). Two modes of operation are supported (over and over-under). G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-241...
Page 456
Eq. 5-50 and offset is the split phase current at no-load. In “Over” mode, the element picks up if > pickup) and (I ≥ min_load) Eq. 5-51 split bias load 5-242 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 457
| > pickup) and (I ≥ min_load) Eq. 5-52 split bias load Figure 5-127: Split phase protection operating characteristics Settings are described as follows. — This setting enables and disables the function. SPLIT PHASE FUNCTION G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-243...
Page 458
CTs (first figure presented). In this instance, a time delay can be used to ride through the saturation event. Alternately, the CT saturation flag also can be used to supervise the function. 5-244 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Figure 5-128: Split phase protection logic 5.7.10 Voltage elements 5.7.10.1 Menu SETTINGS GROUPED ELEMENTS SETTING GROUP 1(6) VOLTAGE ELEMENTS VOLTAGE ELEMENTS PHASE See below UNDERVOLTAGE1 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-245...
Page 460
600.00 seconds in steps of 0.01. The undervoltage elements can also be programmed to have an inverse time delay characteristic. The undervoltage delay setting defines the family of curves shown as follows. Eq. 5-53 5-246 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 461
Range: 0.000 to 3.000 pu in steps of 0.001 VOLTAGE: 0.100 pu PHASE UV1 BLOCK: Range: FlexLogic operand PHASE UV1 Range: Self-reset, Latched, Disabled TARGET: Self-reset PHASE UV1 Range: Disabled, Enabled EVENTS: Disabled G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-247...
Page 462
The input voltage is the phase-to-phase voltage, either measured directly from delta-connected VTs or as calculated from phase-to-ground (wye) connected VTs. The figure shows specific voltages to be used for each phase. 5-248 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 463
FlexCurves A, B, or C) or be used as a definite time element. The setting applies only if the NEUTRAL OV1 PICKUP DELAY setting is “Definite Time.” The source assigned to this element must be configured for a phase VT. NEUTRAL OV1 CURVE G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-249...
Page 464
There are three negative-sequence overvoltage elements available. Use the negative-sequence overvoltage element to detect loss of one or two phases of the source, a reversed phase sequence of voltage, or a non-symmetrical system voltage condition. 5-250 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 465
Range: Disabled, Enabled Disabled The G30 contains one auxiliary undervoltage element for each VT bank. This element monitors undervoltage conditions of the auxiliary voltage. selects the voltage level at which the time undervoltage element starts timing. The nominal secondary...
Page 466
Range: Disabled, Enabled Disabled The G30 contains one auxiliary overvoltage element for each VT bank. This element is intended for monitoring overvoltage conditions of the auxiliary voltage. The nominal secondary voltage of the auxiliary voltage channel entered under SYSTEM is the per-unit (pu) base used when setting the SETUP ...
Page 467
If the voltage mode is set as “Phase- phase”, then the operating quantity for this element is the phase-to-phase nominal voltage. Likewise, if the voltage G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-253...
Page 468
“Phase-ground”, then the operating quantity for this element is the phase-to-ground nominal voltage. It is beneficial to use the phase-to-phase voltage mode for this element when the G30 device is applied on an isolated or resistance-grounded system.
Page 469
TDM = Time Delay Multiplier (delay in sec.) V = fundamental RMS value of voltage (pu) F = frequency of voltage signal (pu) Pickup = volts-per-hertz pickup setpoint (pu) The figure shows the volts/hertz inverse B curves. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-255...
Page 470
TDM = Time Delay Multiplier (delay in sec.) V = fundamental RMS value of voltage (pu) F = frequency of voltage signal (pu) Pickup = volts-per-hertz pickup setpoint (pu) The figure shows the volts/hertz inverse C curves. 5-256 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
LOSS OF EXCITATION Range: 0.000 to 65.535 s in steps of 0.01 PKP DELAY2: 0.500 s LOSS OF EXCITATION Range: 0.000 to 1.250 pu in steps of 0.001 UV SUPV: 0.700 pu G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-257...
Page 472
‘blocked’ event if events are enabled, and becomes inactive. When unblocked, the element starts functioning instantly. If exposed to pickup conditions for an extended period of time and unblocked, the element picks up and starts timing out at the moment of unblocking. 5-258 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
The operating quantity is displayed in the actual value. ACTUAL VALUES METERING SENSITIVE DIRECTIONAL POWER 1(2) The element has two independent (as to the pickup and delay settings) stages for alarm and trip, respectively. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-261...
Page 476
For example, section (a) in the figure shows settings for reverse power, while section (b) shows settings for low forward power applications. 5-262 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 477
DIR POWER 1 RCA setting to “90°,” active underpower by setting to “180°,” and reactive underpower by DIR POWER 1 RCA DIR POWER 1 RCA setting to “270°.” DIR POWER 1 RCA G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-263...
Page 479
Phase CT Primary x Phase VT Ratio x Phase VT Secondary in case of delta connected VTs and as 3 x Phase CT Primary x Phase VT Ratio x Phase VT Secondary in case of wye connected VTs. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-265...
Figure 5-146: Third harmonic neutral undervoltage logic 5.8 Control elements 5.8.1 Overview Control elements are used for control rather than protection. See the Introduction to Elements section at the beginning of this chapter for information. 5-266 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Once the required element is selected for a specific bus, a list of element operate-type operands are displayed and can be assigned to a trip bus. If more than one operate-type operand is required, it can be assigned directly from the trip bus menu. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-267...
Page 482
TRIP BUS 1 RESET RESET OP operand is pre-wired to the reset gate of the latch, As such, a reset command from the front panel interface or via communications resets the trip bus output. 5-268 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Prevents the active setting group from changing when the selected FlexLogic operand is "On." This SETTING GROUPS BLK — can be useful in applications where it is undesirable to change the settings under certain conditions, such as during a control sequence. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-269...
RANGE: 7 SELECTOR 1 TIME-OUT: Range: 3.0 to 60.0 s in steps of 0.1 5.0 s SELECTOR 1 STEP-UP: Range: FlexLogic operand SELECTOR 1 STEP-UP Range: Time-out, Acknowledge MODE: Time-out 5-270 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 485
(“Acknowledge” mode). When the new position is applied, the relay displays the SELECTOR SWITCH 1: POSITION Z IN USE message. Typically, a user-programmable pushbutton is configured as the stepping up control input. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-271...
Page 486
(that is, the three-bit input is not available (0,0,0) or out of range), then the selector switch output is set to position 0 (no output operand selected) and an alarm is established ( SELECTOR 1 PWR ALARM 5-272 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 487
The selector position pre-selected via the three-bit control input has not been confirmed before the time The following figures illustrate the operation of the selector switch. In these diagrams, “T” represents a time-out setting. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-273...
Page 488
CONTROL ELEMENTS CHAPTER 5: SETTINGS Figure 5-150: Time-out mode 5-274 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 489
1 through 3. The pre-selected setting group is to be applied automatically after five seconds of inactivity of the control inputs. When the relay powers up, it is to synchronize the setting group to the three-bit control input. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-275...
Page 490
SETTINGS PRODUCT menu: SETUP USER-PROGRAMMABLE PUSHBUTTONS USER PUSHBUTTON 1 : “Self-reset” PUSHBUTTON 1 FUNCTION : “0.10 s” PUSHBUTTON 1 DROP-OUT TIME The figure shows the logic for the selector switch. 5-276 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
The channels are searched for the signal input in the following order: voltage channel A, auxiliary voltage channel, current channel A, and ground current channel. The first available signal is used for frequency calculation. 5-278 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Range: 0 to 65.535 s in steps of 0.001 DELAY: 0.000 s FREQ RATE 1 RESET Range: 0 to 65.535 s in steps of 0.001 DELAY: 0.000 s FREQ RATE 1 BLOCK: Range: FlexLogic operand G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-279...
Page 494
If the signal source assigned to the frequency rate of change element is only set to auxiliary VT, then the minimum voltage supervision is 3 V. Figure 5-155: Frequency rate of change logic 5-280 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 497
V1 or V2 to traverse an angle equal to 2 × ΔΦ at a frequency equal to the frequency difference ΔF. This time is calculated by: Eq. 5-60 where ΔΦ is phase angle difference in degrees ΔF is frequency difference in Hz G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-283...
Page 498
— Specifies the minimum slip frequency allowed in Hz in the dynamic mode. The dynamic mode is SYNCHK1 S-CLS MIN dF disarmed when the slip frequency drops below this setting. — Specifies the breaker closing time in seconds. SYNCHK1 S-CLS BRK TIME 5-284 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 499
VAG from the other source. If the comparison is required on a specific voltage, the user can externally connect that specific voltage to auxiliary voltage terminals and then use this "Auxiliary Voltage" to check the synchronism conditions. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-285...
Page 500
The relay uses the phase channel of a three-phase set of voltages if programmed as part of that source. The relay uses the auxiliary voltage channel only if that channel is programmed as part of the Source and a three-phase set is not. 5-286 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 501
CHAPTER 5: SETTINGS CONTROL ELEMENTS Figure 5-159: Synchrocheck logic G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-287...
DIGITAL ELEMENT 1 RESET DELAY — This setting enables or disabled the digital element pickup LED. When set to “Disabled,” the DIGITAL ELEMENT 1 PICKUP LED operation of the pickup LED is blocked. 5-288 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 503
In most breaker control circuits, the trip coil is connected in series with a breaker auxiliary contact that is open when the breaker is open (see figure). To prevent unwanted alarms in this situation, the trip circuit monitoring logic must include the breaker position. Figure 5-161: Trip circuit example 1 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-289...
Page 504
In this case, it is not required to supervise the monitoring circuit with the breaker position – the setting is BLOCK selected to “Off.” In this case, the settings are as follows (EnerVista example shown). 5-290 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 506
If control power is interrupted, the accumulated and frozen values are saved into non-volatile memory during the power-down operation. 5-292 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 508
— Selects the threshold value above which the output operand is set. BKR 1 ARC AMP LIMIT 5-294 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 509
-cycle) and AMP MAX (kA) values of the last event. — This setting specifies the maximum symmetrical interruption rating of the circuit breaker. BKR 1 INTERUPTION RATING Figure 5-164: Arcing current measurement G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-295...
Page 510
CONTROL ELEMENTS CHAPTER 5: SETTINGS Figure 5-165: Breaker arcing current logic 5-296 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 511
CT FAIL 1 3V0 INPUT — Specifies the pickup value for the 3V_0 source. CT FAIL 1 3V0 INPUT PICKUP — Specifies the pickup delay of the CT failure element. CT FAIL 1 PICKUP DELAY G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-297...
Page 512
Once the fuse failure condition is declared, it is sealed-in until the cause that generated it disappears. 5-298 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 514
) is limited to 8, even when realistically it is exceeding this value. The reset time of the thermal overload protection element is also time delayed using following formula: Eq. 5-63 where 5-300 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 515
, element starts increasing the thermal energy: Eq. 5-64 When current is less than the dropout level, I > 0.97 × k × I , the element starts decreasing the thermal energy: Eq. 5-65 where G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-301...
The figure shows the logic for the thermal overload protection element. Figure 5-169: Thermal overload protection logic 5.9 Inputs/outputs 5.9.1 Contact inputs SETTINGS INPUTS/OUTPUTS CONTACT INPUTS CONTACT INPUTS 5-302 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 517
The DC input voltage is compared to a user-settable threshold. A new contact input state must be maintained for a user-settable debounce time in order for the G30 to validate the new contact state. In the following figure, the debounce time is set at 2.5 ms;...
Note that the 52b contact is closed when the breaker is open and open when the breaker is closed. 5.9.2 Virtual inputs SETTINGS INPUTS/OUTPUTS VIRTUAL INPUTS VIRTUAL INPUT 1(64) VIRTUAL INPUT 1 VIRTUAL INPUT 1 Range: Disabled, Enabled FUNCTION: Disabled 5-304 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 521
USER PUSHBUTTON 1 USER PUSHBUTTON 2 : “Self-reset” PUSHBUTTON 1 FUNCTION : “0.00 s” PUSHBTN 1 DROP-OUT TIME : “Self-reset” PUSHBUTTON 2 FUNCTION : “0.00 s” PUSHBTN 2 DROP-OUT TIME G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-307...
Page 522
A latching contact H1a is to be controlled from a single virtual output VO1. The contact is to remain closed as long as VO1 is high, and is to remain opened when VO1 is low. Program the relay as follows. 5-308 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
— Represents the state of the direct input when the associated direct device is offline. The DIRECT INPUT 1 DEFAULT STATE following choices are available: • On — Defaults the input to Logic 1 5-310 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 525
UR IED 2: “Cont Ip 1 DIRECT OUT 12 OPERAND On” operand of UR IED 2 is now available in UR IED 1 as Cont Ip 1 On DIRECT INPUT 5 ON G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-311...
Page 526
(if any default state is set to “On”), or to trip the bus on any overcurrent condition (all default states set to “Off”). Example 3: Pilot-aided schemes Consider a three-terminal line protection application shown in the following figure. 5-312 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 527
5" (forward a message from 1 to 3) DIRECT OUT 3 OPERAND "DIRECT INPUT 6" (forward a message from 3 to 1) DIRECT OUT 4 OPERAND The figure shows the signal flow among the three IEDs. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-313...
The “Latest/On” and “Latest/Off” values freeze the input in case of lost communications. If the latest state is not known, such as after relay power-up but before the first communication exchange, then the input defaults to logic 1 for “Latest/ On” and logic 0 for “Latest/Off.” 5-314 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 529
(teleprotection outputs at the sending end or corresponding teleprotection inputs at the receiving end). On three-terminal two-channel systems, redundancy is achieved by programming signal re-transmittal in the case of channel failure between any pair of relays. Figure 5-179: Teleprotection input/output processing G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-315...
VALUE: 0.000 The G30 is provided with optional DCmA capability. This feature is specified as an option at the time of ordering. See the Order Codes section in chapter 2 for details. Hardware and software are provided to receive signals from external transducers and to convert these signals into a digital format for use as required.
1.5 pu. FlexElement operands are available to FlexLogic for further interlocking or to operate an output contact directly. See the following table for reference temperature values for each RTD type. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-317...
DCMA OUTPUT F1 Range: –90.000 to 90.000 pu in steps of 0.001 MIN VAL: 0.000 pu DCMA OUTPUT F1 Range: –90.000 to 90.000 pu in steps of 0.001 MAX VAL: 1.000 pu 5-318 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 533
— This setting allows selection of the output range. Each DCmA channel can be set independently DCMA OUTPUT F1 RANGE to work with different ranges. The three most commonly used output ranges are available. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-319...
Page 534
The CT ratio is 5000:5 and the maximum load current is 4200 A. The current is to be monitored from 0 A upwards, allowing for 50% overload. The phase current with the 50% overload margin is: Eq. 5-72 5-320 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 535
±0.5% of the full scale for the analog output module, or ± 0.005 x (1-0) x 254.03 kV = ±1.27 kV • ±0.5% of reading For example, under nominal conditions, the positive-sequence reads 230.94 kV and the worst-case error is 0.005 × 230.94 kV + 1.27 kV = 2.42 kV. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-321...
FUNCTION: Disabled The G30 provides a test facility to verify the functionality of contact inputs and outputs, some communication functions and the phasor measurement unit (where applicable), using simulated conditions. The test mode can be in any of three states: Disabled, Isolated, or Forcible.
: Normal FORCE Cont Op xx Range: Normal, Energized, De-energized, Freeze : Normal The force contact outputs feature provides a method of performing checks on the function of all contact outputs. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 5-323...
Page 538
While the selected operand is Off, the output behaves as it does when in service. On restart, the setting and the force contact input and force contact output settings revert to TEST MODE FORCING their default states. 5-324 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
The front panel can be viewed and used in the EnerVista software, for example to view an error message displayed on the front panel. To view the front panel in EnerVista software: Click Actual Values > Front Panel. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Access Actual Values > Graphical Panel > Annunciator Panel. Alarms are listed, allowing remote acknowledgement/ reset. Click the Acknowledge or Reset button for an alarm. Figure 6-2: Annunciator alarms displayed in the software) G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Range: On, Off STATUS: Off The G30 is provided with optional IEC 61850 capability. This feature is specified as a software option at the time of ordering. See the Order Codes section of chapter 2 for details. 6.3.4 RxGOOSE DPS inputs ACTUAL VALUES ...
STATUS CHAPTER 6: ACTUAL VALUES The G30 is provided with optional IEC 61850 capability. This feature is specified as a software option at the time of ordering. See the Order Codes section of chapter 2 for details. 6.3.5 Teleprotection inputs ACTUAL VALUES ...
Offline The G30 is provided with optional IEC 61850 capability. This feature is specified as a software option at the time of ordering. See the Order Codes section of chapter 2 for details. actual value does not consider RxGOOSE that are not configured or are not used by any RxGOOSE All RxGOOSE Online Input.
6.3.14 Real time clock synchronizing ACTUAL VALUES STATUS REAL TIME CLOCK SYNCHRONIZING REAL TIME CLOCK RTC SYNC SOURCE: Range: see below SYNCHRONIZING None GRANDMASTER ID: Range: any 8 octet value 0X0000000000000000 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
SIGNATURE: 0 SLOW EXCHANGE 1 DATA LENGTH: 0 These values provide information for debugging an EGD network. The EGD signature and packet size for the slow EGD exchanges display. 6-10 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
UR over Ethernet, the Modbus TCP status shows 3. If the EnerVista application is closed, the Modbus TCP status shows 4. For the graphical front panel, the remaining connections refer to TCP connections only. — The number of IEC 61850 connections remaining. MMS TCP G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 6-11...
Range: 0 to 4G, blank if PRP disabled The G30 is provided with optional PRP capability. This feature is specified as a software option at the time of ordering. See the Order Codes section in chapter 2 for details.
GOOSE or for R-GOOSE when setting R-TxGOOSE1 DST IP is multicast. 6.4 Metering 6.4.1 Metering conventions 6.4.1.1 UR convention for measuring power and energy The figure illustrates the conventions established for use in UR devices. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 6-13...
Page 552
6.4.1.2 UR convention for measuring phase angles All phasors calculated by URs and used for protection, control and metering functions are rotating phasors that maintain the correct phase angle relationships with each other at all times. 6-14 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 553
For display and oscillography purposes the phase angles of symmetrical components are referenced to a common reference as described in the previous sub-section. WYE-connected instrument transformers • ABC phase rotation: • ACB phase rotation: The above equations apply to currents as well. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 6-15...
Page 554
* The power system voltages are phase-referenced – for simplicity – to V and V , respectively. This, however, is a relative matter. It is important to remember that the G30 displays are always referenced as specified under SETTINGS SYSTEM SETUP POWER SYSTEM FREQUENCY AND PHASE REFERENCE The example above is illustrated in the following figure.
0.000 A SRC 1 RMS Ic: 0.000 A SRC 1 RMS In: 0.000 A SRC 1 PHASOR Ia: 0.000 A 0.0° SRC 1 PHASOR Ib: 0.000 A 0.0° 6-18 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 557
0.000 V 0.0° SRC 1 RMS Vab: 0.00 V SRC 1 RMS Vbc: 0.00 V SRC 1 RMS Vca: 0.00 V SRC 1 PHASOR Vab: 0.000 V 0.0° G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 6-19...
Page 558
SRC 1 REACTIVE PWR φc: 0.000 var SRC 1 APPARENT PWR 3φ: 0.000 VA SRC 1 APPARENT PWR φa: 0.000 VA SRC 1 APPARENT PWR φb: 0.000 VA 6-20 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 559
S = V x Î x Î x Î Eq. 6-1 When VTs are configured in delta, the G30 does not calculate power in each phase and three-phase power is measured as S = V x Î x Î Eq. 6-2...
Page 560
= 1, 2,..., N – 1 is the index over one cycle for the Fast Fourier Transform (FFT) m is the last sample number for the sliding window h = 1, 2,..., 25 is the harmonic number The short-time Fourier transform is applied to the unfiltered signal: Eq. 6-3 6-22 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
The tracking frequency displays here. The frequency is tracked based on the selection of the reference source with the setting in the menu. See the Power FREQUENCY AND PHASE REFERENCE SETTINGS SYSTEM SETUP POWER SYSTEM System section of chapter 5 for details. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 6-23...
× I for the +IN and –IN inputs BASE BASE BASE SOURCE THD & HARMONICS BASE = 1% SOURCE VOLTAGE = maximum nominal primary RMS value of the +IN and –IN inputs BASE 6-24 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
0.000 The G30 is provided with optional GOOSE communications capability. This feature is specified as a software option at the time of ordering. See the Order Codes section of chapter 2 for details. The RxGOOSE Analog values display in this menu. The RxGOOSE Analog values are received via IEC 61850 GOOSE messages sent from other devices.
To view them in a web browser, enter the IP address of the device. When an oscillography icon displays, click it to open it. Figure 6-6: Event records viewed in EnerVista software G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 6-27...
5 for details. A trigger can be forced here at any time by setting “Yes” to the FORCE TRIGGER? command. See the COMMANDS CLEAR menu for information on clearing the oscillography records. RECORDS 6-28 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
BREAKER OPERATING TIME All of the values are stored in non-volatile memory and retained with power cycling. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 6-29...
FRONT PANEL PROGRAM Range: 0.00 to 655.35 REVISION: 2.01 Revision number of front panel program firmware. COMPILE DATE: Range: YYYY/MM/DD HH:MM:SS 2016/09/15 04:55:16 Date and time when product firmware was built. 6-30 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 569
The shown data is illustrative only. A modification file number of 0 indicates that, currently, no modifications have been installed. The date format reflects the format specified for the clock and can vary from that shown here. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 6-31...
Page 570
PRODUCT INFORMATION CHAPTER 6: ACTUAL VALUES 6-32 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
The commands menu contains relay directives intended for operations personnel. All commands can be protected from unauthorized access via the command password; see the Security section of chapter 5 for details. The following flash message appears after successfully command entry. COMMAND EXECUTED G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
This menu contains commands for clearing historical data such as the event records. Data is cleared by changing a command setting to “Yes” and pressing the key. After clearing data, the command setting automatically reverts to ENTER “No.” G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
PERFORM PUSHBUTTON Range: No, Yes TEST? No UPDATE ORDER CODE? Range: No, Yes REBOOT RELAY? Range: No, Yes SERVICE COMMAND Range: 0, 101 SAVE VOLATILE DATA? Range: No, Yes G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Although the diagnostic information is cleared before the G30 is shipped from the factory, the user can want to clear the diagnostic information for themselves under certain circumstances. For example, you clear diagnostic information after replacement of hardware.
A target enables the EnerVista UR Setup software to monitor automatically and display the status of any active target messages of all the devices inserted into that site. Each G30 element with a TARGET setting has a target message that when activated by its element is displayed in sequence with any other currently active target messages in the menu.
Contact Factory (xxx) • Latched target message: Yes. • Description of problem: One or more installed hardware modules is not compatible with the G30 order code. • How often the test is performed: Module dependent. • What to do: Contact the factory and supply the failure code noted in the display. The “xxx” text identifies the failed module (for example, F8L).
Page 577
MAINTENANCE ALERT: Direct I/O Ring Break • Latched target message: No. • Description of problem: Direct input and output settings are configured for a ring, but the connection is not in a ring. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 578
Latched target message: No. • Description of problem: A data item in a configurable GOOSE data set is oscillating. • How often the test is performed: Upon scanning of each configurable GOOSE data set. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 579
This time can be from milliseconds to minutes. • What to do: Check GOOSE setup. TEMP MONITOR: OVER TEMPERATURE • Latched target message: Yes. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 580
V-type CPU = All ports support RJ45 SFPs only The consequence of an incorrect SFP can range from damage to the G30 to no power information for the G30 on its web page (enter IP address in a web browser, then click the SFP Transceiver Information — only the type of SFP displays and not power data).
Page 581
Any abnormal diagnostic condition indicated by the LEDs or the critical failure relay also results in a self-test Plus message, so troubleshooting is described here. For other relays, such at the B95 , see that product’s instruction manual. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 7-11...
Page 582
Brick, but there is a discrepancy between the settings and the actual Brick serial number, order code, and/or core number. Check that the correct core on the correct Brick is patched through to the correct Process Card 7-12 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 583
Brick output failing to respond to an output command can only be detected while the command is active, and so in this case the target is latched. A latched target can be unlatched by pressing the front panel reset key if the command has ended, however the output can still be non-functional. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 7-13...
Page 584
TARGETS MENU CHAPTER 7: COMMANDS AND TARGETS 7-14 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
In-zone transformer with VT on the low-voltage (LV) side • With no in-zone transformer 8.1.2 In-zone transformer with VT on the high-voltage side Consider the generator protection system show, with an in-zone transformer with VT on the high-voltage (HV) side. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 586
The difference seen by the differential is the transformer phase shift plus the CT phase shift, or –30° + (–180°) = –210°. The transformer configuration is therefore as shown in the following figure. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Consider the generator protection system shown, with an in-zone transformer with VT on the low-voltage (LV) side. Figure 8-2: Typical wiring, VT on the low-voltage side of the transformer The two sources are configured as follows. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
1. In this case, the only phase shift that must be accounted for is the phase shift of the transformer. Winding 2 is therefore shifted by –30°. 8.1.4 No in-zone transformer Consider the generator protection system shown, with no in-zone transformer. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 589
The two sources are configured as follows. The G30 requires the use of the transformer windings settings for the differential element, even if the differential is applied only as a stator differential for the generator. These settings ensure that the differential element operates with the correct phase shifts, and applies the correct magnitude compensation.
PHASE VT RATIO = Eq. 8-3 NEUTRAL VT RATIO = Eq. 8-4 Enter the following values through the EnerVista software or the front panel SETTINGS SYSTEM SETUP AC INPUTS menu. VOLTAGE BANK F5 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Elements using the auxiliary VT input are assigned to the “GEN” source. Make the following changes through the EnerVista software or the front panel SETTINGS SYSTEM SETUP SOURCE 1 menus. SETTINGS SYSTEM SETUP SOURCE 2 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Stage 2 is typically set lower than stage 1 with a time delay to prevent nuisance alarms for external faults that are normally cleared by system protection. For the application example, the pickup setting is: Eq. 8-6 Source 2 is to be chosen for this element. The settings are as follows. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
The source used for loss of excitation produces positive power when the machine is generating. Make the following changes in the EnerVista software or the front panel SETTINGS GROUPED ELEMENTS SETTING GROUP 1 LOSS OF menu. EXCITATION G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
System backup protection is implemented using a phase time overcurrent element with voltage restraint enabled. The NEUTRL source is to be chosen for this element. Set the pickup of this element at a safe margin above the maximum load expected on the machine. Eq. 8-17 8-10 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 595
The neutral source is chosen. Make the following changes in the EnerVista software or the front panel SETTINGS menu. GROUPED ELEMENTS SETTING GROUP 1 PHASE CURRENT PHASE TOC1 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 8-11...
The following inputs and outputs are used in this example. Make the following changes in the EnerVista software or the front panel menus. SETTINGS INPUTS/OUTPUTS CONTACT INPUTS CONTACT INPUT H7a(H7c) 8-12 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
The elements are to be blocked when offline. Underfrequency is to initiate a trip. Overfrequency is to alarm only. Either source can be assigned. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 8-13...
SETTING S GROUPED ELEMENTS SETTING menu. GROUP 1 ACCIDENTAL ENERGIZATION 8.2.12 FlexLogic The following logic as given as an example. The logic for each specific application depends on system design, protection philosophies, and operating practices. 8-14 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 599
CHAPTER 8: APPLICATION OF SETTINGS SETTINGS Figure 8-6: Application example FlexLogic G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 8-15...
Page 600
SETTINGS CHAPTER 8: APPLICATION OF SETTINGS 8-16 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Injection to a particular G30 frequency element must be to its configured source and to the channels that the source uses for frequency measurement. For frequency measurement, a source uses the first quantity configured in the following...
Page 602
0.20 Hz before the threshold and subtract 1 second from the test set time reading of ramp start to relay operation. Note that the G30 event records only show the “pickup delay” component, a definite time timer. This is exclusive of the time taken by the frequency responding component to pickup.
10.1 Directional principle 10.1.1 Current directional protection For better security, the G30 uses the current directional protection principle to dynamically supervise the main current differential function. The directional principle is in effect permanently for low differential currents (region 1 in the Two Regions of Differential Characteristic figure) and is switched on dynamically for large differential currents (region 2 in the same figure) by the saturation detector (see the Saturation Detector section) upon detecting CT saturation.
10.2.1 CT saturation detection The saturation detector of the G30 takes advantage of the fact that any CT operates correctly for a short period of time, even under very large primary currents that would subsequently cause a very deep saturation. As a result, in the case of...
Page 605
This must be kept in mind when setting the characteristic as its parameters must retain their original meaning. The operation of the saturation detector is available as the FlexLogic operand XFMR PCNT DIFF SAT A/B/C. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 10-3...
Page 606
SATURATION DETECTOR CHAPTER 10: THEORY OF OPERATION Figure 10-4: Saturation detector state machine 10-4 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
UR Family Communications Guide for the entries. The upper part of the window displays values. The lower part of the window is for factory service use. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 11-1...
Page 608
Float — A numbering system with no fixed number of digits before or after the decimal point. An example is 0.000000. Binary — A numbering system using 0 and 1. An example is 0000-0000-0000-0000. Entries are not saved when closing the window. 11-2 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
GENERAL MAINTENANCE 11.2 General maintenance The G30 requires minimal maintenance. As a microprocessor-based relay, its characteristics do not change over time. Expected service life is 20 years for UR devices manufactured June 2014 or later when applied in a controlled indoor environment and electrical conditions within specification.
Page 610
Using the Up or Down pushbuttons on the front panel, select the file. Press the COPY pushbutton. The files are copied from the G30 to the USB drive. Do not unplug the USB drive while copying is in progress, else the USB drive can be compromised.
Convert the settings by right-clicking one of the files in the Offline Window and selecting the Convert Device Settings option. GE recommends converting settings in firmware steps, for example when converting from 6.0 to 7.4x, convert first to 7.0 then 7.4 in order to follow embedded conversion rules and keep settings.
Page 612
Change settings in the new file, for example by looking at the original file. Write the converted file to the device, for example by dragging and dropping from the Offline Window to the Online Window. Check settings and operation. 11-6 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
11.5 Copy settings to other device Settings from one G30 device can be copied to another G30 device for rapid deployment. The order codes must match. See the Settings File section at the beginning of the Interfaces chapter for a list of settings not deployed, such as IP address.
To save the report, click File > Save As, select the TXT, PDF, or CSV format from the drop-down list, and enter a name for the file. To compare settings between Online and Offline devices: Right-click a device in the Online Window area and select Compare with Device. 11-8 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Have this option enabled when you want to keep the IID file from the UR device instead of from another tool. The location of the file is C:\ProgramData\GE Power Management\urpc\Offline, for example.
Page 616
To save settings in the ICD format in EnerVista Offline Window: In EnerVista, right-click the device in the Offline Window area. Select the Create ICD File option. Or select the Save As option, and select the ICD option from drop-down list. 11-10 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Right-click the .urs file in the Offline Window area and select Add Device from File to locate a file, and/or drag-and- drop the file from the Offline Window area to the device in the Online Window area. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 11-11...
Page 618
In Windows, make a copy the IID file with a cid extension. Connect to the device in the Online Window area. In the Offline Window area, right-click Devices and select Import Devices from SCD. 11-12 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
UR 7.4 can be used to access multiple UR devices that have version 7.4x, 7.2x, and 6.0x firmware installed. Existing installations do not need to be uninstalled before upgrade. You can also downgrade the software; use the same procedure. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 11-13...
For Windows 10, to finish installing the UR USB driver, open Device Manager > Ports, then plug in the USB cable (to connect the relay and computer). A new port starting with "GE Virtual Serial Port" is available. If available, click the OK button to complete the installation.
Page 621
You access the Convert Device Settings option by right-clicking the file in the Offline Window area at the lower left. GE recommends converting settings in firmware steps, for example when converting from 6.0 to 7.4x, convert first to 7.0 then 7.4 in order to follow embedded conversion rules and keep settings. Note that the values of all settings that have been defaulted during conversion are not listed in the conversion report;...
For an enhanced front panel, loosen the thumb screw and open slightly the front panel. For a standard front panel, lift up the black plastic latch on the right side of the front panel and open slightly the front panel. 11-16 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 623
With a Phillips screwdriver, unscrew and remove the mounting bracket on the right side of the unit. The bracket for the enhanced front panel looks similar to that for the graphical front panel, but they are not the same. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 11-17...
Page 624
Figure 11-15: Remove standard front panel mounting bracket on right side Open the front panel. Unplug or unscrew the grey ground cable from the front panel. Unplug the RJ45 connector from the CPU module in the second slot on the left. 11-18 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 625
Unscrew and remove the mounting bracket with the front panel from the left side. Figure 11-17: Unscrew enhanced front panel mounting bracket on left side Figure 11-18: Unscrew standard front panel mounting bracket on left side G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 11-19...
Page 626
Figure 11-19: Attach mounting bracket to relay on left side (no power supply module in first slot) Screw the right mounting bracket to the right side of the relay. 11-20 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 627
Close the front panel without tightening the screw to the mounting bracket. Optionally remove the protective plastic film on the graphical front panel. It is normally peeled off, but also can be left The graphical front panel has been installed but not connected. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 11-21...
Page 628
Ensure that the RS485 connector and the black cover plate are not on the back of the CPU module before sliding the module into the front of the relay. Figure 11-23: Rear of a CPU module before insertion without RS485 connector or cover plate 11-22 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 629
Insert the silver SFP connector(s) at the back of the CPU module, then connect any Ethernet connection(s). Power up the relay. If the graphical front panel does not power up immediately, disconnect power, open the front G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 11-23...
Open the enhanced front panel to the left once the thumb screw has been removed. This allows for easy access of the modules for withdrawal. The new wide-angle hinge assembly in the enhanced front panel opens completely and allows easy access to all modules in the G30. Figure 11-26: Modules inside relay with front cover open (enhanced front panel) 11-24 G30 GENERATOR PROTECTION SYSTEM –...
To avoid injury, ensure that the unit has been powered off for a minimum of three minutes before replacing the battery. Risk of fire if battery is replaced with incorrect type or polarity. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 11-25...
10. Reinstall the battery holder and the metal cover, and reinsert the power supply module into the unit. 11. Power on the unit. 12. Dispose of the old battery as outlined in the next section. 11.13.2 Dispose of battery 11-26 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 633
Paristo on merkitty tällä symbolilla ja saattaa sisältää cadmiumia (Cd), lyijyä (Pb) tai elohopeaa (Hg). Oikean kierrätystavan varmistamiseksi palauta tuote paikalliselle jälleenmyyjälle tai palauta se paristojen keräyspisteeseen. Lisätietoja sivuilla www.recyclethis.info. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 11-27...
Page 634
Batteriet er merket med dette symbolet som kan inkludere symboler for å indikere at kadmium (Cd), bly (Pb), eller kvikksølv (Hg) forekommer. Returner batteriet til leverandøren din eller til et dedikert oppsamlingspunkt for korrekt gjenvinning. For mer informasjon se: www.recyclethis.info. 11-28 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 635
Bu sembolle işaretlenmiş piller Kadmiyum(Cd), Kurşun(Pb) ya da Civa(Hg) içerebilir. Doğru geri dönüşüm için ürünü yerel tedarikçinize geri veriniz ya da özel işaretlenmiş toplama noktlarına atınız. Daha fazla bilgi için: www.recyclethis.info. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL 11-29...
For issues not solved by troubleshooting, the process to return the device to the factory for repair is as follows: • Contact a GE Grid Solutions Technical Support Center. Contact information is found in the first chapter. • Obtain a Return Materials Authorization (RMA) number from the Technical Support Center.
Customers are responsible for shipping costs to the factory, regardless of whether the unit is under warranty. • Fax a copy of the shipping information to the GE Grid Solutions service department in Canada at +1 905 927 5098. Use the detailed return procedure outlined at https://www.gegridsolutions.com/multilin/support/ret_proc.htm...
Field RTD 5 Value Field RTD 5 value 5829 Field RTD 6 Value Field RTD 6 value 5830 Field RTD 7 Value Field RTD 7 value 5831 Field RTD 8 Value Field RTD 8 value G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 640
SRC 2 Ic Angle Degrees Source 2 phase C current angle 6225 SRC 2 In Mag Amps Source 2 neutral current magnitude 6227 SRC 2 In Angle Degrees Source 2 neutral current angle G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 641
6353 SRC 4 In Mag Amps Source 4 neutral current magnitude 6355 SRC 4 In Angle Degrees Source 4 neutral current angle 6356 SRC 4 Ig RMS Amps Source 4 ground current RMS G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 642
SRC 2 Vcg Mag Volts Source 2 phase CG voltage magnitude 6734 SRC 2 Vcg Angle Degrees Source 2 phase CG voltage angle 6735 SRC 2 Vab RMS Volts Source 2 phase AB voltage RMS G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 643
SRC 4 Vag RMS Volts Source 4 phase AG voltage RMS 6850 SRC 4 Vbg RMS Volts Source 4 phase BG voltage RMS 6852 SRC 4 Vcg RMS Volts Source 4 phase CG voltage RMS G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 644
Source 2 phase C real power 7208 SRC 2 Q Vars Source 2 three-phase reactive power 7210 SRC 2 Qa Vars Source 2 phase A reactive power 7212 SRC 2 Qb Vars Source 2 phase B reactive power G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 646
SRC 1 Vb Harm[6] Source 1 phase B voltage sixth harmonic 8095 SRC 1 Vb Harm[7] Source 1 phase B voltage seventh harmonic 8096 SRC 1 Vb Harm[8] Source 1 phase B voltage eighth harmonic G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 647
SRC 2 Va Harm[3] Source 2 phase A voltage third harmonic 8142 SRC 2 Va Harm[4] Source 2 phase A voltage fourth harmonic 8143 SRC 2 Va Harm[5] Source 2 phase A voltage fifth harmonic G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 648
Source 2 phase B voltage twenty-fifth harmonic 8189 SRC 2 Vc THD Source 2 phase C voltage total harmonic distortion (THD) 8190 SRC 2 Vc Harm[2] Source 2 phase C voltage second harmonic A-10 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 649
SRC 3 Va Harm[22] Source 3 phase A voltage twenty-second harmonic 8236 SRC 3 Va Harm[23] Source 3 phase A voltage twenty-third harmonic 8237 SRC 3 Va Harm[24] Source 3 phase A voltage twenty-fourth harmonic G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL A-11...
Page 650
SRC 3 Vc Harm[19] Source 3 phase C voltage nineteenth harmonic 8283 SRC 3 Vc Harm[20] Source 3 phase C voltage twentieth harmonic 8284 SRC 3 Vc Harm[21] Source 3 phase C voltage twenty-first harmonic A-12 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 651
SRC 4 Vb Harm[16] Source 4 phase B voltage sixteenth harmonic 8330 SRC 4 Vb Harm[17] Source 4 phase B voltage seventeenth harmonic 8331 SRC 4 Vb Harm[18] Source 4 phase B voltage eighteenth harmonic G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL A-13...
Page 652
Transformer restraint phase B current angle 8973 Xfmr Harm2 Ibd Mag % fo Transformer differential phase B second harmonic current magnitude 8974 Xfmr Harm2 Ibd Angle Degrees Transformer differential phase B second harmonic current angle A-14 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 653
SRC 1 Ib Harm[6] Source 1 phase B current sixth harmonic 10279 SRC 1 Ib Harm[7] Source 1 phase B current seventh harmonic 10280 SRC 1 Ib Harm[8] Source 1 phase B current eighth harmonic G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL A-15...
Page 654
SRC 2 Ia Harm[3] Source 2 phase A current third harmonic 10342 SRC 2 Ia Harm[4] Source 2 phase A current fourth harmonic 10343 SRC 2 Ia Harm[5] Source 2 phase A current fifth harmonic A-16 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 655
Source 2 phase B current twenty-fifth harmonic 10405 SRC 2 Ic THD Source 2 phase C current total harmonic distortion 10406 SRC 2 Ic Harm[2] Source 2 phase C current second harmonic G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL A-17...
Page 656
SRC 3 Ia Harm[22] Source 3 phase A current twenty-second harmonic 10460 SRC 3 Ia Harm[23] Source 3 phase A current twenty-third harmonic 10461 SRC 3 Ia Harm[24] Source 3 phase A current twenty-fourth harmonic A-18 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 657
SRC 3 Ic Harm[19] Source 3 phase C current nineteenth harmonic 10523 SRC 3 Ic Harm[20] Source 3 phase C current twentieth harmonic 10524 SRC 3 Ic Harm[21] Source 3 phase C current twenty-first harmonic G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL A-19...
Page 658
SRC 4 Ib Harm[16] Source 4 phase B current sixteenth harmonic 10586 SRC 4 Ib Harm[17] Source 4 phase B current seventeenth harmonic 10587 SRC 4 Ib Harm[18] Source 4 phase B current eighteenth harmonic A-20 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 660
Breaker 1 amp max phase B 12052 Brk 1 Amp Max C kA2-cyc Breaker 1 amp max phase C 12054 Brk 2 Acc Arc Amp A kA2-cyc Breaker 2 Acc arcing amp phase A A-22 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 661
RTD input 7 actual value 13559 RTD Ip 8 RTD input 8 actual value 13560 RTD Ip 9 RTD input 9 actual value 13561 RTD Ip 10 RTD input 10 actual value G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL A-23...
Page 662
Current setting group 32768 Tracking Frequency Terminal tracking frequency 39168 FlexElement 1 Value FlexElement 1 actual value 39170 FlexElement 2 Value FlexElement 2 actual value 39172 FlexElement 3 Value FlexElement 3 actual value A-24 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 663
45632 RxGOOSE Analog 25 RxGOOSE analog input 25 45634 RxGOOSE Analog 26 RxGOOSE analog input 26 45636 RxGOOSE Analog 27 RxGOOSE analog input 27 45638 RxGOOSE Analog 28 RxGOOSE analog input 28 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL A-25...
Page 664
45640 RxGOOSE Analog 29 RxGOOSE analog input 29 45642 RxGOOSE Analog 30 RxGOOSE analog input 30 45644 RxGOOSE Analog 31 RxGOOSE analog input 31 45646 RxGOOSE Analog 32 RxGOOSE analog input 32 A-26 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
UR device for successful authentication, and the shortname is a short, optional alias that can be used in place of the IP address. client 10.0.0.2/24 { secret = testing123 shortname = private-network-1 In the <Path_to_Radius>\etc\raddb folder, create a file called dictionary.ge and add the following content. # ########################################################## GE VSAs ############################################################ VENDOR...
Page 666
Access Settings > Product Setup > Security. Configure the IP address and ports for the RADIUS server. Leave the GE vendor ID field at the default of 2910. Update the RADIUS shared secret as specified in the clients.conf file. Restart the relay for the IP address and port changes to take effect.
When the Supervisor account is enabled, the 'Lock Relay' setting must first be changed to No before the putsettings, inservice, or reboot command can be used. This setting cannot be changed using the command line interface. • Use quotes ("") to enclose any parameter containing a space G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 668
For non-CyberSentry devices — Set <authentication type> to "traditional". Note that <authentication type> defaults to "traditional" if not specified. Set <account> to "COMMANDS" or "SETTINGS". If not specified, the SETTINGS account is used. Example: SetupCLI URPC login -d "C30 Melbourne" -A traditional -a SETTINGS -w 1password1 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 669
Read settings from device <device> and save them to the .urs file <File>. The <File> must not already exist. The default path to the output file is C:\Users\Public\Public Documents\GE Power Management\URPC\Data Example: SetupCLI URPC getsettings -d C30 -f "C30 Markham.urs"...
Page 670
SetupCLI URPC getsettings -d demoDevice -f devicefile.urs SetupCLI URPC compare -f existingfile.urs -r devicefile.urs -o output.txt The output is similar to the following: Comparing settings file aaa.urs : C:\Users\Public\Public Documents\GE Power Management\URPC\Data\ with bbb.urs : C:\Users\Public\Public Documents\GE Power Management\URPC\Data\ Setting Name...
Page 671
SetupCLI URPC getsettings -d DEV@SETUP_CLI -f "example file.urs" SetupCLI URPC logout -d DEV@SETUP_CLI SetupCLI URPC exit DEV@SETUP_CLI has to be used as the device name in the commands followed by the 'adddevice' command. G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 672
COMMAND LINE INTERFACE APPENDIX C: COMMAND LINE INTERFACE G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
This chapter provides the warranty and revision history. D.1 Warranty For products shipped as of 1 October 2013, GE Grid Solutions warrants most of its GE manufactured products for 10 years. For warranty details including any limitations and disclaimers, see the Terms and Conditions at http://www.gegridsolutions.com/multilin/warranty.htm...
Page 674
1601-0166-AF2 7.6x 31 October 2017 17-3935 Table D-2: Major changes for G30 manual version AF2 (English) Page Description General revision Added type W CPU module to order codes in chapter 2, installation chapter 3, Replace Front Panel section in chapter 10 Added Japanese and Polish languages and modules 6W and 6X to order codes in chapter 2.
Page 675
Added Convert Device Settings section 11-7 Added Copy Settings to Other Device section 11-15 Added Replace Front Panel section for retrofit with the new graphical front panel Table D-4: Major changes for G30 manual version AE3 (English) Page Description General revision Updated order codes...
Page 676
Added Support for Routable GOOSE section 5-177 Updated number of FlexLogic lines from 512 to 1024 in FlexLogic Equation Editor settings section 10-1 Added Monitoring section 10-2 Added Retrieve Files section Added Command Line Interface appendix G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 677
Finite Impulse Response Contact Output Full Load Current Communication Fiber Optic COMM Communications FPGA Field-programmable Gate Array COMP Compensated, Comparison FREQ Frequency CONN Connection Frequency-Shift Keying CONT Continuous, Contact File Transfer Protocol CO-ORD Coordination FlexElement™ G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 678
Loopback Power Line Carrier Line Pickup Positive Locked-Rotor Current POTT Permissive Over-reaching Transfer Trip Load Tap-Changer PRESS Pressure Low Voltage Primary PROT Protection Machine Parallel Redundancy Protocol Machine to Machine PSEL Presentation Selector G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 679
Time, transformer Thermal Capacity Transmission Control Protocol Thermal Capacity Used TD MULT Time Dial Multiplier TEMP Temperature TFTP Trivial File Transfer Protocol Total Harmonic Distortion Timer Time Overcurrent Time Overvoltage TRANS Transient TRANSF Transfer G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 680
ABBREVIATIONS G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 681
Add relay ....................3-57 Arcing current ..................5-294 Attempt to contact RADIUS server failed message ..7-11 Audit list of port numbers ............... 5-45 Authentication by device or server ........... 5-16 Authentication fail message ............7-11 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 682
FlexLogic operands ...............5-179 settings ....................5-158 with IEC 61850 .................. 5-89 Breaker-and-a-half scheme ............5-6 Brightness ....................5-26 C37.94 communications ............. 3-48, 3-51 Cannot log in .................... 2-6 Caution symbol in Offline Window ........... 4-68 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 683
CPU module diagram ................3-12 Default settings ................ 11-7, 11-9 CPU, new types T, U, V ..............11-16 Definite time curve ............5-213, 5-246 CRC alarm .....................5-138 Delete files and records .............5-40, 11-30 Critical failure relay specifications ..........2-32 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 684
....................5-311 Engineer toolbar .................. 4-80 specifications ..................2-33 Directional overcurrent see Phase, Ground, and Neutral directional Directional polarization ..............5-217 Directional power, sensitive actual values ......6-25 Directional power, sensitive specifications ......2-22 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 685
..........2-32 status in single-line diagram of graphical front panel ... 4-31 Fast transient testing specifications ........2-38 timer settings ...................5-194 Features ...................... 2-1 worksheet ..................5-191 Fiber signal loss detection ..............5-46 Force contact inputs ...............5-323 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 686
................. 7-9 USB port ..................... 5-108 types ...................... 4-15 use, change setting ................. 4-52 use ......................4-15 Ground current metering ............... 6-19 use in EnerVista ............... 4-17, 6-3 FUNCTION setting .................. 5-5 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 687
Internet access IEC 60870-5-104 protocol ..................5-99 Inter-relay communication specifications ......2-35 connections remaining ..............6-11 Inverse time undervoltage ............5-246 port, close ..................5-101 select protocol ...................5-51 settings ....................5-100 see Phase, Ground, and Neutral IOCs G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 688
........4-59, 5-21 THD specifications ................2-29 Local access, explained ..............5-8 voltage specifications ..............2-28 Local Setting Authorization ............11-15 Metering editor ..................4-35 Lockout from software ..............5-14 Microsoft Windows requirement ..........3-55 viii G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 692
............... 5-74, 5-76, 5-77 Setting groups ............5-199, 5-200, 5-269 preferences ..................11-9 active setting group ..............5-199 Second Ethernet Fail ................. 5-38 FlexLogic operands ..............5-182 troubleshooting ................5-200 Setting lock self-test ................7-11 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 693
Synchronize Devices ...............5-110 system requirements ..............3-55 Syslog ......................5-25 update or downgrade ..............11-13 System and device information ..........4-76 Source frequency ................6-22 System failure error ................7-7 Source transfer schemes .............5-246 System frequency ................5-143 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL xiii...
Page 695
Voltage deviation specifications ..........2-38 Upgrade device settings ..............11-5 Voltage elements ................5-246 Upgrade over Internet message ..........11-15 URS file does not include IEC 61850 configuration ..11-12 URS file is part of a device folder ..........11-12 G30 GENERATOR PROTECTION SYSTEM – INSTRUCTION MANUAL...