CD display section 1. Reverse Mode Switch 2. Timer Record Switch 2. Play indicator: w 3. FM Mode Switch 3. Track Number Indicator 4. Funcbon Selector Buttons 4. Minutes and Seconds lndlcator 5. Main Power Switch 5. MUSIC Schedule Indicators 6.
Aim (wIthIn the ranoe of 30” with no obstacles1 the remote control at the remofe control &nsar and operate as sh&n Notes concerning use: l Replace the batteries If control distance decreases or oper- l Exposmg the sensor on the ma,” un,t to strong light can the “...
Page 8
n Recording from the built-in radio BEAT CANCEL n Erasing recorded tapes n APSS spacing...
Page 9
To record radio programmes You can record a broadcasting station different from that to which you are listening. However, the band should be the same. Load a blank cassette tape into the TAPE 2 cassette corn- correct. n Timer operation To listen to the radio preset station on the remote control.
Page 10
Black Removing the CD mechanism Caution on Disassembly Follow the below-mentioned notes when disassembling ths Following the disassembling procedure, steps 1 and 2, remove unit and reassemblmg it, to keep its safety and excellent per- the CD mechanism. formance: 1. Take cassette tape and compact disc out of the unit. Removing the frame (with main/CD switch/function 2.
Page 17
Since the adjusting procedure differs from that described in “ ADJUSTMENT PROCEDURES OF AUDIO PRODUCTS” , refer to the Service Manual. All the semivariable resistors must be set in the mechanical center position Test Stage Value/Adjusting Method Instrument Connecl~on Set TEST MODE 0. and move the oickuo to the center Set Test MODE 1 (make sure that the laser lamp Ilghts) heard.) Set TEST MODE 3 (Spin servo is turned on.
of CNPBBf.~/ k the LCD PWB of CD. (Check the LD ON terminal of pin 9 of IC97f.) Check the +5 V line of pin 1 of CNPBBI. there +5 V at the a890 collector? Check between pin 17 of CNP851B and Q890 base. If OK, 0890 is defective. Is there +5 V at pin 5 of CNP700? k The PWB pattern between 0890 and pin 5 of CNP700 is damaged.
Page 19
0.3 - 1.5sec 0.3 - 1.5sec m u t i n g ) . C h e c k t h e connection between the pins 1 and a n d IC814. between the...
1. Tuner To differentiate the units of resistors, such symbol as K and ( ): AM mode M are used, the symbol K means 1000 ohm and the symbol Marking except for ( ): FM mode M means 1000 kohm and the resistor without any symbol 2.
Page 33
NOTES ON SCHEMATIC DIAGRAM can be found on page 41. waveform numbers shown page Q Figure 45 SCHEMATIC DIAGRAM (115)
REPLACEMENT PARTS LIST To have your order filled promptly and correctly, please furnish the following information. 1. MODEL NUMBER 2. REF. NO. 3. PART NO. 4. DESCRlPTlON Parts marked with “ ,&,” are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the safety and performance of the set.
Page 46
DESCRIPTION REF.NO. CODE REF.NO. PART NO. DESCRIPTION CODE PART NO. D104 RVR-Ml002AFZZ J 47 kohms (B),Semi-VR D108 [FM Autostop Sens.] RVR-M0997AFZZ J 5 kohms (B),Semi-VR VR251 [Tape Speed] RVR-P0167AFZZ J 100 kohm (A), [BASS] k o h m ( ) , [ V O L U M E J Silicon,lSSl33 VR700...
Page 51
PART NO. CODE PART ND. PART ND. PART NO. SW859 J Spr!ng,Cam Trigger Arm T A P E LENGTH1 SW860 J Cam Gear,FF/REW Q S W - K O 1 7 2 A F Z Z J Switch.Key Type OTHER CIRCUITRY PARTS J Arm.Trigger Cassette1 J Swltch,Key Type...
Page 52
T iNSZ1203AFLZ J Operation Manual J Spring.Battery,+/-,“D” J Label feature,Tape 1 J Spring,Battery,-,“D”Slze H o l d e r , J Label.Feature.Speaker Printed in Japan Tape 1 Writer and Editor: Quality & Reliability Control Center of Audio Systems Group, Sharp Corp.