A other hazard. free replacement manual is available by sending the complete Model and Serial Number to The Toro – Reduce your speed when making sharp turns and Company, 8111 Lyndale Avenue South, Bloomington, when turning on hillsides.
• To ensure optimum performance and safety, always purchase genuine Toro replacement parts and accessories to keep the machine all Toro. Never use “will-fit” replacement parts and accessories made by other manufacturers. Look for the Toro logo to ensure genuineness.
Safety and Instruction Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. 98-3110 1. Danger–See Operator’s 4. Always wear eye Manual protection 105-4593 2.
Specifications General Specifications 5000 CFM Fan Output 165 MPH Fan Speed 2575 RPM Outlet Area Adjustable outlet opening, 39 to 70 square inches Directional Control 90 degree outlet deflector operated from seat Castor Wheels Two 8 x 3–1/2 inch solid rubber tires Height Adjustment 4 to 6–1/2 inches Adjustment is with 1/2 inch spacers and holes in castor fork Ground Clearance–Transport 11–1/4 inches...
Clamping Plate Mount blower to traction unit. Reinforcing Plate Capscrew Flatwasher Flange Nut Cable Tie Secure hydraulic hoses to blower housing Operator’s Manual Read before operating the machine. Parts Catalog Registration card Fill out and return to Toro. Declaration of Conformity...
Note: Determine the left and right sides of the machine 4. Remove hair pin cotters and clevis pins securing from the normal operating position. height-of-cut chains to rear of deck (Fig. 3). Retain hair pin cotters and clevis pins for re–installation of front deck Remove Front Cutting Unit 1.
Mount Arm Assemblies 1. Align the rear set of mounting holes in each lift arm with holes in the blower housing mounting brackets. Position lift arms as shown in figure 5. 2. Loosely secure each lift arm to mounting bracket with (2) capscrews, flatwashers and locknuts.
1. Using a 1/8” Allen wrench, remove orifice plug from MR port of front PTO manifold (Fig. 9). 2. Order plug Part No. 3246–17 from your Toro distributor and install into MR port of manifold with a 5/32” Allen wrench.
2. Mount each lift arm ball joint mount to each side of blower arm assembly with (2) capscrews (4) flatwashers and (2) locknuts. Position fasteners as shown in figure 10. 3. Mount each lift arm to top of each blower arm assembly with (2) capscrews (2) flatwashers, clamping plate, reinforcing plate and (2) locknuts.
Operation 6. Secure hydraulic hoses to blower housing with wire tie (Fig. 14). Note: Determine the left and right sides of the machine from the normal operating position. Operating Tips Warning Discharged air has considerable force and could cause injury or loss of footing. •...
Figure 16 Figure 15 1. Discharge opening 3. Handle assembly deflector screw 1. Locking cap 3. Thrust washers 2. Discharge direction 2. Spacers deflector Adjust Discharge Opening Adjust Discharge Direction The discharge opening (Fig. 16) is adjustable to increase or Lower deflector assembly in front of discharge opening to decrease air output velocity and volume.
Maintenance Note: Determine the left and right sides of the machine from the normal operating position. Greasing the Blower The debris blower must be lubricated regularly. If machine is operated under normal conditions, lubricate castor and fan bearings and bushings with No. 2 general purpose lithium base grease or molybdenum base grease, after every 8 hours of operation or daily, whichever comes first.
4. Insert pin punch into top or bottom of bumper and drive bushing out of tube (Fig. 19). Also drive other bushing out of bumper. Clean inside of bumper to remove any dirt. Figure 20 1. Outer bearing 2. Inner bearing Figure 19 1.
If for any reason you are dissatisfied with your Distributor’s service or have difficulty obtaining guarantee information, contact the Toro importer. If all other remedies fail, you may contact us at Toro Warranty Company.