Download Print this page
Pentek GS-6 Instruction Manual

Pentek GS-6 Instruction Manual

Inline water filter

Advertisement

Quick Links

Inline Water Filter Instruction Manual
Models GS-6, GS-10, GS-210, GS-215, GS-6RO, GS-10RO, GS-210RO,
GS-215RO, GS-6ALS, GS-10ALS, GS-215CB5-S, GS-215CB5

Specifications

Temperature Range:
40–100°F (4.4–37.8°C)
Pressure Range:
20–125 psi (1.4–8.62 bar)
Capacity/Flow Rate:
GS-6
500 gallons (1893 L) @ 0.5 gpm (1.9 Lpm)
GS-10
750 gallons (2839 L) @ 1 gpm (3.8 Lpm)
GS-210
1,000 gallons (3785 L) @ 1 gpm (3.8 Lpm)
GS-215
1,250 gallons (4732 L) @ 1 gpm (3.8 Lpm)
GS-6RO
1,650 gallons (6246 L) @ 0.5 gpm (1.9 Lpm)
GS-10RO
3,308 gallons (12522 L) @ 0.5 gpm (1.9 Lpm)
GS-210RO
6,000 gallons (22712 L) @ 1 gpm (3.8 Lpm)
GS-215RO
8,950 gallons (33879 L) @ 1 gpm (3.8 Lpm)
GS-6ALS
585 gallons (2214 L) @ 0.5 gpm (1.9 Lpm)
GS-10ALS
1,400 gallons (5110 L) @ 1 gpm (3.8 Lpm)
GS-215CB5
3,500 gallons (31249 L) @ 1 gpm (3.8 Lpm)
GS-215CB5-S
3,500 gallons (31249 L) @ 1 gpm (3.8 Lpm)
Dimensions:
GS-6
2" x 6" (50.8 mm x 152.4 mm)
GS-10
2" x 10" (50.8 mm x 254 mm)
GS-210
2.5" x 11" (63.5 mm x 279.4 mm)
GS-215
2.5" x 14 63.5 mm x 355.6 mm)
GS-6RO
2" x 6" (50.8 mm x 152.4 mm)
GS-10RO
2" x 10" (50.8 mm x 254 mm)
GS-210RO
2.5" x 11" (63.5 mm x 279.4 mm)
GS-215RO
2.5" x 14" (63.5 mm x 355.6 mm)
GS-6ALS
2" x 6" (50.8 mm x 152.4 mm)
GS-10ALS
2" x 10" (50.8 mm x 259 mm)
GS-215CB5
2.5" x 14" (63.5 mm x 355.6 mm)
GS-215CB5-S
2.5" x 14" (63.5 mm x 355.6 mm)
GS-6, GS-10, GS-210, GS-215, GS-6RO, GS-10RO, GS-210RO, GS-215RO, GS-6ALS,
GS-10ALS, GS215-CB5, and GS215CB5-S, are Tested and Certified by NSF
International against NSF/ANSI Standard 42. See Performance Data Sheet in
manual for specific claims.
Technical Support: 800.279.9404 (M-F 8:00 a.m. - 5:00 p.m. CST)
Precautions
WARNING:
Do not use with water that is microbiologically unsafe
or of unknown quality without adequate disinfection
before or after the system.
CAUTION:
Filter must be protected against freezing, which can
cause cracking of the filter and water leakage.
CAUTION:
Install this cartridge on cold water lines only. Do not use
on water lines exceeding 100º F (37.2º C). Minimum water
pressure of 20 psi (1.4 bar) and maximum water pressure
of 125 psi (8.62 bar) is required.
CAUTION:
When installing behind a refrigerator or appliance use
ample amount of tubing to allow removal of refrigerator
or appliance and to prevent damage to tubing, filter or
fittings. Damage to tubing, filter or fittings could cause
leakage and damage.
NOTE: Activated carbon cartridges will contain a small amount of
carbon fines (very fine black powder). A new cartridge, after
installation, should be flushed with water for 5 minutes, wait an
hour then flush another 5 minutes to remove the fines before
using the water.
NOTE: Even after the filter has been flushed to remove the fines, it is
possible that some settling of the carbon can occur and the
first trays of ice cubes or water may be discolored. Discard the
ice cubes or flush out with more water, if this is the case.
NOTE: Substances reduced are not necessarily in your water. Filter
must be maintained according to manufacturer's instructions,
including replacement of filter cartridges.
NOTE: Keep this unit clean with soap and water. Do not use spray
cleaners or insecticides near the unit.
NOTE: Do not install filter close to a heat source.
NOTE: Comply with all state and local laws and regulations
Installation Recommendations
1. Inline filters are most effective when water flows down through
the filter. Install with the inlet port at the top and the outlet port at
the bottom.
2. Install in a location convenient for filter replacement.
3. In-line filter life depends upon the water volume used and
the substances present in the water source. Manufacturer
recommends changing the filter every 6 to 12 months or when its
capacity expires, whichever comes first.
WARNING:
Do not use with water that is microbiologically unsafe
or of unknown quality without adequate disinfection before or after
the system.
NOTE: Substances reduced are not necessarily in your water.
Filter must be maintained according to manufacturer's instructions,
including replacement of filter cartridges.
146732 Rev C JL10

Advertisement

loading

Summary of Contents for Pentek GS-6

  • Page 1: Specifications

    NOTE: Substances reduced are not necessarily in your water. GS-6, GS-10, GS-210, GS-215, GS-6RO, GS-10RO, GS-210RO, GS-215RO, GS-6ALS, GS-10ALS, GS215-CB5, and GS215CB5-S, are Tested and Certified by NSF Filter must be maintained according to manufacturer’s instructions, International against NSF/ANSI Standard 42.
  • Page 2: Installation Instructions

    Replacement Cartridges water leaks or loosening of Contact your local PENTEK dealer for replacement cartridges. tube from the fitting. Outlet Port (Collet Fitting – Inlet the same) 4476 0104 Figure 3 Collet Style Fittings: A.
  • Page 3 Performance Data continued Models GS-210RO, GS-215RO Model GS-6 Maximum Maximum Influent Permissible Influent Permissible Challenge Product Water Reduction Minimum Average Challenge Product Water Reduction Minimum Average Substance Concentration Concentration Requirements Reduction Reduction Substance Concentration Concentration Requirements Reduction Reduction Standard 42 Aesthetic Effects...
  • Page 4 Inline Water Filter PENTEK Filtration/Pentair Filtration, Inc. warrants to the original owner (under normal use): Inline water filter to be free from defects in material and/or workmanship one (1) year from the date of purchase. Any replacement products furnished will be free from defects in material and/or workmanship for the remainder of the original warranty period.

This manual is also suitable for:

Gs-10Gs-210Gs-215Gs-6roGs-10roGs-210ro ... Show all