Assembling And Adjusting The Clutch; Assembling The Clutch Components; Clutch Adjustment - Fiat 411 R Service Manual

- check ciearance between bushes and disengagement lever pins;
- check piate spring characteristics;
- check the throw-out coiiar working siiding surface. If wear does not exceed the permissible iimiis.
the shaft can be mounted again after rotating it 'i8G°; if necessary replace the parts when grease
I drips due to excessive clearance.
i i
' Assembling and adiusting the cluich.
1_;_,i;,;i¢a1§Qn_ Smear iighiiy the foiiowing oomponenis before
i i assembling using quaiity chassis grease:
— the clutch disengagement lever pivots, the cievis
ends confaciing the disengagement fevers (3.
Fig. 34), the c1uZcn~gearb-ox and the clutch power
* iaise-off shaft splines, the baii ends of push
levers (P, Fig. 88), the ciei/is fever ends where
confaciing the disengagement collar; in addition
service the bearing housing in engine fiywneei.
i
i .-.-
$ ,....._.._
' l _ : _ f : T
*' _ ~ i ~ < — - - -
W 1 155%,
_, ' f .' - ~'/
-
i \ 1"'
i s ._;.._-r;- ". '\
»'=='- F I
,-
\__._.....a- r 1 __ i_i
i "'7"-"'2 1 {YT ' : ,- ' 1 ' e .' § -";?.-' i "-' § '-'§»' = _**-'Q=~' ~ *-._._- II"--\.,_\
v ~ vi . " ~ .=. 1:1. — ' 1:.-es. w . .
1 ' ' ' _.-1:?-E§~\"'€' -' w " '- "'39::§'7;F "ro- - W' 3" . .'\';=""..,=\_-' ""<I=i_»:w, " r"-.=
M ' '.__¢_ '- ¥;'-'_" -"7 51;'-Lei".-:-'='_l P 5": 'P'. V . " _' \
_ .._ C ,;x_>,;y_~ < cw xx vu - ..e. '_.;§'1.;<.-.;E;ii;i==.=i'; 531,'-;Tf§;f"-;7;' * ___=, _;?.'§ _ Z .\
— — __ __— ":7 ca: -_ *_, .- _\ *"'1'<1'"" ' ._'_ -.-1-Y » . . .
'£-2.~¢-'=I-*- i. l:I{'*'—'$_"" ' ' ' - -=.:=~.'~:— ,. -.1 T' .e¢;::'=v'" ;_=.=-~"_»1.'=_=+e3~...' . ' -, _
=—» W i
_ i-1.->.$'1,_ .':.;-..-. ., ' :,;jij;u;-;—\;-
T. ' _ T. ' . ' _ \
rams.
in
. 3 3»).
C4
- , fi ~! 4 . ' » §
was
_--.' ' _ T . . . _ . _ . " ' _ .
. 4/
, , . _ _ .
" m i /'
i, i
I 3 i *
X i' 2
,1--—m-I'--\ "-"' s__
' * ~ 'Cf.._'\" ,_
W _
"Fag. av. 1 Cluich section.
, Fig. 83. - Clutch piaie centering with reference to points P.
} Assembling the ciutch components. it is easiiy performed by foiiowfng Figs. 86 and 8?
' and caring that the ciuich-gearbox piate is centered
i with reference to the caps and that the eiasific pins
are oriented as shown in Fig. 35.
Clutch assembly £0 be performed on fixture A 711063,
using if on the side marked with the tractor number.
For clutch adjustment ii is noi necessary io place
upon the fixture A 'I11i}63 the power take-off disc,
which remains outside the assernbiy, and is subsu-
iuted by a ring (Fig. 89) superposed to fixture E.
Ciutch adiustment.
56
|
I
1
: § F.
ii ' -
1- .1
I
.- J.
IA
' 1-'7'?l7g":T'.'-5-'Z:~: :;_." . '-':=l1;"'a.i!";',-; , .,
' _i _ ;.7?' § ".i:_.f'_§:'-' 'f-"1 f.}. '1'-': '§:;'-§]L;i=T%¢fifi1-j§»"" '
~._ . i ' _.;_-1 -. 'I _..v . ..
; s
1' 3
VI'
ii