Advertisement
Quick Links
IMPORTANT!
TO IDENTIFY COMPUTER RELATED ISSUES AND PREVENT COSTLY TROUBLESHOOTING, BENCH TEST
YOUR MONITOR, KVM EXTENDER, KEYBOARD, AND/OR MOUSE WITH YOUR COMPUTER WITH THE
PROVIDED 25' CAT5 CABLE.
KVM LOCAL AND REMOTE MODULES COME FROM THE FACTORY AS MATCHED PAIRS (MATCHED BY
SERIAL NUMBER) AND ARE TUNED AND TESTED AS SUCH. NEVER USE MISMATCHED PAIRS OF LOCAL
AND REMOTE MODULES.
1. Install the KVM Local Module and cabling according to the instructions in the
Adderlink X2 Dual Access manual.
NOTE: Power supply will be required if PS2 cables are not hooked up
to the computer. If your computer does not have PS2 ports, do not use
a 3rd party USB to PS2 adapter. Please use the Hope Industrial adapter
(part number CUSB-CCP2U).
2. Lay the monitor face down on a clean work surface with the bottom of the
monitor facing you. Use a soft cloth or piece of foam as a pad to prevent
scratching the front of the monitor.
3. Remove the eight existing screws around the cable access opening on the
rear cover of the monitor.
4. Install the video cable, power cable, and RS-232 cable (for touch screen
units) from the KVM Remote Module into the Universal Mount Monitor.
Secure the screw locks on the video and RS-232 cables.
5. Insert the KVM Remote Module into the opening of the rear panel by sliding
the right hand locking tabs in all the way to the right.
6. Press down firmly and slide the KVM Remote Module to the left until it stops
with both left hand locking tabs securely inside the rear panel.
7. Install the CAT5 cable from the KVM Local Module and power cable into the
KVM Remote Module.
NOTE: Do not use your KVM Extender to link between different buildings.
Linking between different buildings that do not share a common earth
ground is not supported and may damage your KVM Extender.
99028G • January 6, 2015 • www.HopeIndustrial.com • International: +1 (678) 762-9790 • UK: +44 (0) 20 7193 2618 • © 2015 Hope Industrial Systems, Inc. • Page 1 of 2
Installation Instructions
KVM2EXT-BLK-N4-PS2 or KVM2EXT-SS-N4X-PS2
Rear-Mounted PS2/Serial KVM Extender
KVM REMOTE MODULE
(COVER PLATE NOT
SHOWN FOR CLARITY)
REAR COVER
LEFT HAND
LOCKING TABS
COVER PLATE
SEALING WASHERS
(UNDER EACH SCREW)
RIGHT HAND
LOCKING TABS
UNIVERSAL
MOUNT
MONITOR
KEYBOARD
(OPTIONAL)
Advertisement
Related Manuals for HIS KVM2EXT-BLK-N4-PS2
Summary of Contents for HIS KVM2EXT-BLK-N4-PS2
-
Page 1: Installation Instructions
Installation Instructions KVM2EXT-BLK-N4-PS2 or KVM2EXT-SS-N4X-PS2 Rear-Mounted PS2/Serial KVM Extender IMPORTANT! TO IDENTIFY COMPUTER RELATED ISSUES AND PREVENT COSTLY TROUBLESHOOTING, BENCH TEST YOUR MONITOR, KVM EXTENDER, KEYBOARD, AND/OR MOUSE WITH YOUR COMPUTER WITH THE PROVIDED 25' CAT5 CABLE. KVM LOCAL AND REMOTE MODULES COME FROM THE FACTORY AS MATCHED PAIRS (MATCHED BY SERIAL NUMBER) AND ARE TUNED AND TESTED AS SUCH. - Page 2 Rear-Mounted PS2/Serial KVM Extender Instructions (continued) 8. For monitors without a keyboard, temporarily plug a keyboard into the keyboard PS2 port of the KVM Remote Module. Download the Adder test pattern generator from the following address: http://www.HopeIndustrial.com/links/addertest Perform the image adjustments found in the “Image controls” and “Skew adjustment” sections of the AdderLink X2 Dual Access manual. After completing the image adjustment, unplug the temporary keyboard and continue to step 10. 9. For monitors with a keyboard, install the keyboard by following the installation instructions that were shipped with the keyboard. Download the Adder test pattern generator from the following address: http://www.HopeIndustrial.com/links/addertest Plug the connectors into the KVM Remote Module. Perform the image controls and skew adjustment found in the "Image controls"...