Dynex DX-FANT01-P Quick Setup Manual

DX-FANT01-P / DX-FANT01-G / DX-FANT01-CH / DX-FANT01-B
Table Fans

Important safety information

READ AND SAVE THESE SAFETY INSTRUCTIONS BEFORE USING THIS FAN
When using electrical appliances, basic precautions should always be
followed to reduce the risk of re, electric shock, and injury to persons,
including the following:
FOR US MODELS ONLY – This product employs overload protection (fuse).
A blown fuse indicates an overload or short-circuit situation. If the fuse
blows, unplug the product from the outlet. Replace the fuse
Servicing Instructions (follow product marking for proper fuse rating) and
test the product. If the replacement fuse blows, a short-circuit may be
present and the product should be discarded.
QUICK SETUP GUIDE
1 Use this fan only as described in this manual. Other use not recommended may cause re, electric shock,
or injury to persons.
2 This product is intended for household use ONLY and not for commercial, industrial, or outdoor use.
3 To protect against electric shock, do not place the fan in a window, immerse the fan, plug, or cord in water,
or spray with liquids.
4 This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of shock, this
plug is intended to t only one way in a polarized outlet. If the plug does not t fully in the outlet, reverse
the plug. If it still does not t, contact a quali ed electrician. DO NOT attempt to defeat this safety feature.
5 Close supervision is necessary when any appliance is used by or near children.
6 Unplug the fan from the outlet when not in use, when moving fan from one location to another, and before cleaning.
7 Do not operate the fan in the presence of explosive and/or ammable fumes.
8 Do not place the fan or any parts near an open ame or near a cooking or heating appliance.
9 Do not operate the fan with a damaged cord or plug or if the fan malfunctions or is dropped or damaged
in any manner (see warranty).
10 Avoid contact with moving fan parts.
11 The use of attachments not recommended by the manufacturer may be hazardous.
12 Place the fan on a dry level surface.
13 Do not hang or mount fan on a wall or ceiling.
14 Do not operate if the fan housing is removed or damaged.
15 A loose t between the AC outlet (receptacle) and plug may cause overheating and a distortion of the plug.
Contact a quali ed electrician to replace loose or worn outlet.
16 Do not operate any fan with a damaged cord or plug. Discard any damaged fan, return the fan to the
retailer where the fan was purchased or call Dynex Customer Service at 800-305-2204.
17 Do not run fan cord under carpeting. Do not cover the cord with throw rugs, runners, or similar coverings.
Do not route the cord under furniture or appliances. Place the cord away from tra c areas and where it will
not be tripped over.
WARNING: To Reduce The Risk of Fire or Electric Shock,
Do Not Use This Fan With Any Solid-State Speed Control Device.
Operating your fan
1 Make sure that your fan is in the OFF position.
2 Place your fan on a dry, level surface.
3 Plug the power cord into a polarized 120 volt AC power outlet.
4 Turn the speed control knob to the desired speed setting.
Note: The fan base also serves as a convenient carrying handle.
as per the User
Maintaining your fan
• Be sure your fan is in the OFF position.
• Unplug the fan before cleaning.
• This fan does not disassemble.
• Use only a soft cloth to gently wipe the fan clean.
• DO NOT immerse the fan in water and never allow water to drip into the motor housing.
• DO NOT use gasoline, paint thinner, or other chemicals to clean the fan.
• For storage, clean the fan carefully as instructed and store your fan in a cool dry place.
Fused Safety Plug - For US models only
This fan features a patented fused safety plug which is designed to cut o electric
current to the fan if an electrical fault occurs. Read this Quick Setup Guide for more
information on how to properly use your fan and replace the safety plug fuse, if
needed.
User servicing instructions
1 Grasp plug and remove from the receptacle or other outlet device.
Do not unplug by pulling on cord.
2 If your fan loses power and you suspect that the fuse on your fan has blown, you
should rst remove the spare fuse holder attached to the cord plug. Remove
the spare fuse from the plastic spare fuse holder, and set the spare fuse aside.
3 You can gain access to the blown fuse by sliding open the door found on the
side of the plug. Slide the door outward until the blown fuse is fully visible.
4 Carefully remove the blown fuse and snap the replacement fuse into place.
Risk of re. Replace fuse only with 2.5 Amp, 125 volt fuse (provided with product).
Fully close the fuse door by sliding back into place. Discard the blown fuse.
The plug should now be ready for normal use.
Risk of fire. Do not replace attachment plug. Contains a safety device (fuse)
that should not be removed. Discard product if the attachment plug is damaged.
One-year limited warranty For complete warranty, visit www.dynexproducts.com.
Contact Dynex:
For customer service, call 800-305-2204 www.dynexproducts.com.
© 2011 BBY Solutions, Inc. All Rights Reserved. DYNEX is a trademark of BBY Solutions, Inc.
Registered in some countries. All other products and brand names are trademarks
of their respective owners.
P/N 31IMDYNE190
ENGLISH 11-0248