Summary of Contents for Atlantic TW1200
- Page 1 Operating Manual Includes Pumps: TW1200 TW1900 TW2400 TW3700 TW4800 TW6000 1-877-80-PONDS www.atlanticwatergardens.com...
- Page 2 12’ TW1900 reading this manual supply voltage within 100-120 volt 60 Hz. 8’ TW3700 keep it as a reference TW4800 • Never place your hand or any object in or near the inlet opening while in case questions 4’ TW2400 TW1200 this equipment is operating. If pump inlet is clogged, always turn off arise during use. the power supply and wait until the motor is completely stopped before 1000 2000 3000 4000 5000 6000 attempting to remove any clogged material. G A L L O N S P E R H O U R • Please make sure that the power plug and the AC outlet receptacle is...
- Page 3 • WARNING: • In case of excessive vibration, unusual noise or odor, turn off the power RISK OF ELECTRIC SHOCK - THIS PUMP IS SUPPLIED WITH A GROUNDING CONDUCTOR immediately and consult your nearest dealer. AND GROUNDING-TYPE ATTACHMENT PLUG. TO REDUCE THE RISK OF ELECTRIC SHOCK, BE CERTAIN THAT IT IS CONNECTED ONLY TO A PROPERLY GROUNDED, GROUNDING TYPE RECEPTACLE. Motor Protection System • The pump has a built-in motor protection system. The following reasons Electrical Safety may cause the pump to stop automatically regardless of water level. • Electrical wiring should be installed by a qualified electrician in Motor overheating accordance with all applicable safety regulations. Incorrect wiring can Excessive current lead to a pump malfunction, electrical shock or fire. Change in voltage polarity Open-phase operation or operation under constraint • Pumps should operate on a designated, 110/120 volt circuit. • Repeating cycles of stopping and restarting will damage the water • Pump must be protected by a ground fault circuit interrupter (GFCI). pump. Do not continue operation at low water level or while • Pump must be plugged into a standard, properly grounded, three the inlet is clogged with debris. Not only will performance suffer, but pronged outlet. also such conditions may cause noise, heavy vibration, and pump failure. • Do not cut the electrical cable. If a cable with cut insulation or other Maintenance and Inspection damage is submerged in water, there is danger of water seeping into the pump motor and causing a short. This may result in damage to the...
- Page 4 Winterizing • Remove the four screws using a #2 Phillips screwdriver. • Rotate the impeller/ intake cover counter clockwise 1/4 turn and • Under no circumstances should the pump be left in frozen water. remove by pulling straight out. • When the pump is out of use for an extended period, wash it and dry • Remove the impeller assembly it thoroughly, then store it indoors. Note: Always run a test operation before putting the pump back into operation. When the pump is left installed in water it should be run at regular intervals (about once per week). Warranty All Tidal Wave Pumps carry a two year limited warranty. This limited warranty is extended solely to the original purchaser commencing from the date of original purchase receipt and is void if any of the following apply: • The pump has been run while not fully submersed causing the thermal protection to trip. Skimmers using inadequate vertical filtration may create “run dry” conditions. • The pump was not run on a dedicated circuit. • The cord has been cut or altered. NOTE: If debris has accumulated around the rotor, the impeller may feel tight. Rotate the impeller back and forth while applying outward • The pump has been misused or abused. pressure until the impeller assembly wiggles free. • Serial number tag has been removed. • Inspect the rotor and stator sleeve for built up debris. Often in hard water, well water or pond-free applications, debris may appear as a Warranty Claims crusty film around the rotor. Remove the film using a scrub brush or • In case of warranty claims, pump should be returned to place of scouring pad.
-
Page 5: Troubleshooting Guide
Troubleshooting Guide Always turn off power before inspecting the pump. Failure to observe this precaution can result in a serious accident. Before ordering repairs, carefully read through this instruction booklet. If the problem persists, contact your dealer. Problem Possible Cause Possible Solution Power is off Turn power on Check power supply or Power failure contact local power company Pump does not start Voltage drop/ Check/Replace the GFI (Ground Overload Fault Interrupter) Power cord is not Connect power cord connected Pump is Submerge pump/Raise water level/ overheating Allow pump to cool/Clean impeller Power/Current Check length/size of power cable. Pump stops after overload Check or replace GFI starting Remove debris from the pump Intake is blocked/ intake. Refer to page 7 for Impeller needs cleaned cleaning instructions. Impeller needs cleaned Refer to page 7 for cleaning instructions Diminished...