Air Gunsa AZ30 HTE 1.0 Instruction Manual

AIR GUNSA s.r.l.
46, Corso Vigevano
Quality Air Spray Guns Since 1944 10155 Torino - Italy
Tel. ++39 011 24 80 868
www.anest-iwataeu.com/airgunsa
Fax ++39 011 22 74 406
ANEST IWATA Europe S.r.l.
46, Corso Vigevano
10155 Torino - Italy
Tel. ++39 011 24 80 868
Fax ++39 011 22 74 406
www.anest-iwataeu.com
e-mail: info@anest-iwataeu.com
Instruction Manual
SPRAY GUN AZ30 HTE, AZ30 HTE M&S CUP
Before use, adjustment or maintenance, it is important to read this instruction manual very
GB
carefully. This manual must be stored in a safe place for any future reference that may be necessary.
This AIR GUNSA spray guns kit complies to ATEX regulations 94/9/EC, protection level:
II 2 G X Suitable for using Zones 1 and 2.
X marking: Any static electricity discharge from the spray gun is to be diverted to the ground via the conductive air hose as stipulated.
This spray gun should be operated only by an adequately trained operator, for safe use and maintenance of the equipment. Any
misuse or handling other than those indicated in this Instruction Manual is not covered by guarantee. AIR GUNSA disclaims all
responsibility for any accident or damage caused by failure to observe the operational and safety procedures as from this man-
ual. In the interest of user friendliness, this manual contains information in a brief and concise form.
For any additional information you may require regarding spray guns operations, or if any missing parts or any damage during
transportation is found, please contact your nearest AIR GUNSA Company (see last cover page).
Be sure to observe warnings and cautions in this instruction manual.
If not, it can cause paint ejection and serious bodily injury by drawing organic solvent.
Be sure to observe following
WARNING Indicates a potentially hazardous situation which, if not avoided, may result in serious injury or loss of life.
CAUTION
IMPORTANT
IMPORTANT SPECIFICATIONS
Max. Pressure:
Noise Level (LAeqT)
Spray conditions
Measuring point

TECHNICAL SPECIFICATIONS

Model
AZ30 HTE Gravity feed
AZ30 HTE 1.0
AZ30 HTE 1.3
AZ30 HTE 1.5
AZ30 HTE 1.8
AZ30 HTE 2.0
Distributed by:
(1) Atomizing air pressure means air pressure at gun inlet when trigger is pulled and air flows.
(2) Paint viscosity; 21sec/Ford cup#4
Manufactured by: AIR GUNSA _ Anest Iwata Gruop
IMPORTANT
marked items which are especially important.
Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury or pro-
perty damage.
Indicates notes which we ask you to observe. The safety precautions in this instruction manual are the mini-
mum necessary conditions. Follow national and local regulations regarding fire prevention, electricity and
safety as well as your own company regulations.
7.0 bar (100 PSI)
73.5 dB (A)
Recommended condition in Tech. Specifications
1m backwards from gun, 1,6 m height
Recommended condition
Nozzle Orifice Air Cap (1)Atomizing (2) Fluid
set Mark Air pressure Output Consumption
Ø mm (in) bar (PSI) ml/min Nl/min (cfm)
1.0 (0.039) 10 HP 80
1.3 (0.051) 13 HP 175
1.5 (0.059) 15 HP 2.5 (36) 220
1.8 (0.070) 18 HP 280
2.0 (0.079) 20 HP 315
Max. Temperature:
Atmosphere 5 ~ 40 °C
Air and fluid 5 ~ 43 °C
Air connection: G 1/4"
Fluid connection: G 1/4"
Air Pattern Weight Weight
Width Without Cup With Cup
mm (in) g (lbs) g (lbs)
245 (8.65) 150 (5.90)
600 cc CUP
245 (8.65) 225 (8.85)
640 (1.41)
490 (1.07) ------------
250 (8.82) 260 (10.23)
M&S CUP
270 (9.53) 325 (12.79)
664 (1.46)
270 (9.53) 350 (13.77)