Download Print this page

Imtra Sigma Small Installation And Operation Manual

Sigma powerled downlight

Advertisement

Quick Links

Sigma PowerLED Downlight
Installation and Operation Manual
Sigma
Small
Sigma Surface-Mount shares the same light engine and features
a sleek mounting bezel for installation where recessing is not
possible.
Sigma is a 2-wire dimmable product that simplifies retrofit
installations by allowing the installer to take advantage of the
vessel's existing two wires (or duplex cabling). Sigma is also
compatible with some existing halogen dimmers which may
further simplify installation and minimize the project's wiring
complexity. Sigma's integrated low voltage AC bridge rectifier
permits its use with either 10-40VDC or 12V/24VAC supplied by
magnetic transformers.
Sigma
Sigma
Large
Surface-Mount
- 2 -
OVERVIEW
Imtra PowerLED fixtures are uniquely suited for marine,
automotive and architectural lighting applications. They have
been engineered specifically to take advantage of the latest LED
(Light Emitting Diode) technology offering superior reliability,
minimal power consumption and far less radiated heat than
traditional incandescent light sources. When installed properly,
these products will provide years of flawless performance.
The Sigma series encompasses a common LSA (LED sub-
assembly) platform with different bezel options allowing the user
to choose a model that can easily replace existing lights whether
these are traditional halogen or older LED lights. The flush mount
models are provided with stainless steel mounting springs which
may be easily removed if a screw mount installation is required.
Sigma Small fits flush into a very common hole cutout size; may
be either screw or spring mounted.
Sigma Large shares the same light engine but is equipped with a
special adapter plate and larger diameter trim ring to fit a range
of larger hole cutout sizes; may be screw or spring mounted.

SPECIFICATIONS

Sigma Small
Trim Ring Diameter
3.57" (91mm)
Mounting Base Diam.
N/A
Bezel Height
0.34" (9mm)
Cutout Diameter
2.56" (65mm)
Recess Depth
0.90" (23mm)
Input Voltage Range
Power Consumption
IP Rating
* IP65: "Protected from the ingress of dust and low pressure jets of water from all directions"
- 1 -
Sigma
Sigma Large
Surface-Mount
4.35" (110mm)
3.57" (91mm)
N/A
4.07" (103mm)
0.34" (9mm)
1.25" (32mm)
2.56" (65mm) to
N/A
3.65" (93mm)
0.90" (23mm)
N/A
10-40V (AC/DC)
5.0 Watts
IP65*
- 3 -

Advertisement

loading

Summary of Contents for Imtra Sigma Small

  • Page 1: Specifications

    Sigma Sigma Sigma Sigma Small fits flush into a very common hole cutout size; may Small Large Surface-Mount be either screw or spring mounted.
  • Page 2: Physical Installation

    PHYSICAL INSTALLATION Installation Instructions (Recessed Mount) Whether the lights are installed using the springs provided or Sigma Small and Sigma Large by screw-mounting, it is imperative that the lights be mounted come with mounting springs in such a location that the fixtures are protected from the rear installed.
  • Page 3: Wiring Instructions

    Imtra’s (3) machine screws (included). (see Intervolt DC Dimmer which these lights have been optimized Figure 4). for. Please contact Imtra or visit our website for details on this 4. Place the trim ring over the light dimmer. Figure 4 making sure the tabs of the trim ring 3.
  • Page 4: Limited Warranty

    If it should become necessary to return a fixture for service during or beyond the warranty period, please refer to Imtra’s standard Return Policy 30 Barnet Boulevard, New Bedford, MA 02745 as detailed on Imtra’s website (www.imtra.com) or call Imtra customer (508) 995-7000 •...

This manual is also suitable for:

Sigma surface-mountSigma large