Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for TP-Link TL-PA2010
Summary of Contents for TP-Link TL-PA2010
- Page 1 TL-PA2010 AV200 Nano Powerline Adapter Rev: 1.0.1 1910010708...
- Page 2 Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD.
-
Page 3: Fcc Statement
FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. - Page 4 This product can be used in the following countries:...
-
Page 5: Declaration Of Conformity
TP-LINK TECHNOLOGIES CO., LTD DECLARATION OF CONFORMITY For the following equipment: Product Description: AV200 Nano Powerline Adapter Model No.: TL-PA2010 Trademark: TP-LINK We declare under our own responsibility that the above products satisfy all the technical regulations applicable to the product within the scope of Council Directives: Directives 2004 / 108 / EC, Directives 2006 / 95 / EC, Directives 2011/65/EU The above product is in conformity with the following standards or other normative documents：... -
Page 6: Table Of Contents
CONTENTS Package Contents ............................ Chapter 1 Introduction .......................... 1.1 Conventions .............................. 1.2 System Requirement ....................2 1.3 Important Safety Instructions ..................2 Chapter 2 Connecting Mechanism .................... 2.1 Introduction .............................. 2.2 LED Indicator .............................. 2.3 Physical Interface ............................ -
Page 7: Package Contents
TL-PA2010 AV200 Nano Powerline Adapter Package Contents The AV200 Nano Powerline Adapter package contains the following items: One AV200 Nano Powerline Adapter (There are two AV200 Nano Powerline Adapters in Starter Kit) One RJ-45 Ethernet Cable (There are two RJ-45 Ethernet Cables in Starter Kit) -
Page 8: Chapter 1 Introduction
1． Existing connection with a new unassociated device added via the Pair button. 2． Reset to default setting via the Management Utility. 1.1 Conventions The powerline adapter or AV200 Nano Powerline Adapter mentioned in this guide stands for TL-PA2010 AV200 Nano Powerline Adapter without any explanation. 1.2 System Requirement... - Page 9 TL-PA2010 AV200 Nano Powerline Adapter 8. Plug this product directly into a wall socket (100Vac~240Vac). Do not use an extension cord between this product and the AC power source. 9. When plugging this product into a wall socket, make sure that the electrical socket is not damaged, and that there is no gas leakage.
-
Page 10: Chapter 2 Connecting Mechanism
TL-PA2010 AV200 Nano Powerline Adapter Chapter 2 Connecting Mechanism 2.1 Introduction The Powerline Adapter supports up to 200Mbps data rate. With this high speed connection rate, this Powerline Adapter allows you to setup a high speed home network by using your home existing electrical wiring. -
Page 11: Physical Interface
TL-PA2010 AV200 Nano Powerline Adapter The Ethernet port is connected, but there is no data being transferred. Ethernet LED Blinking The Ethernet port is transferring data. The Ethernet port isn’t connected. Note: 5 minutes after the device connected to the adapter is turned off, and the adapter will automatically switch to the power-saving Mode. -
Page 12: Connection Instruction
TL-PA2010 AV200 Nano Powerline Adapter Note: If you press the Pair button for more than 10 seconds, the Powerline Adapter will leave the network which it is associated with and its network name assumes a random value. The Power LED turns off when it disconnects from the Powerline network. -
Page 13: Hardware Connection - Internet
TL-PA2010 AV200 Nano Powerline Adapter 2.6 Hardware Connection – Internet This section describes how to connect the Powerline Adapter into your existing ADSL broadband connection via ADSL Ethernet port. Follow the procedures described below to connect the Powerline Adapter to your ADSL broadband connection: 1．... - Page 14 TL-PA2010 AV200 Nano Powerline Adapter Note: Do not connect the Powerline adapter to an extension lead, power strip, extension cord, or surge protector as these may degrade the network performance.
-
Page 15: Chapter 3 Installing Management Utility
TL-PA2010 AV200 Nano Powerline Adapter Chapter 3 Installing Management Utility Please verify that no other Powerline Adapter or any Encryption Management Utilities are installed before installing the provided software. If other Powerline Utilities are installed, uninstall them and restart your personal computer before installing this provided software. - Page 16 TL-PA2010 AV200 Nano Powerline Adapter...
- Page 17 TL-PA2010 AV200 Nano Powerline Adapter...
- Page 18 TL-PA2010 AV200 Nano Powerline Adapter Step 3: After the installation, a shortcut to the “Powerline Utility” application icon is provided on the windows desktop.
-
Page 19: Chapter 4 Using The Management Utility
TL-PA2010 AV200 Nano Powerline Adapter Chapter 4 Using the Management Utility After you’d successfully installed the Powerline Adapter hardware and Management Utility software, you can set up or configure the devices according to your need. This Powerline Utility enables the users to identify powerline devices on the powerline network, measures data rate performance and ensures privacy by setting user defined secure powerline networks. -
Page 20: Set Local Device's Network Name
TL-PA2010 AV200 Nano Powerline Adapter MAC Address: Displays the MAC address of the powerline adapter connected to the current computer where this management utility is running. Network Name: Displays the network name of the current network or you can give a name for the network in which the powerline adapter is. -
Page 21: Rename The Remote Device/Enter Password
TL-PA2010 AV200 Nano Powerline Adapter network. Furthermore, here you can change the Name of the listed powerline adapters as well as add another device to the current network. Type: Displays the type of the remote device found in the network. -
Page 22: Add Device
TL-PA2010 AV200 Nano Powerline Adapter network name of this device on System configuration homepage. To change the name of the remote adapter or enter its password, please follow the steps below: (1) Select the desired device and click the Modify button to display the following dialog. -
Page 23: System
TL-PA2010 AV200 Nano Powerline Adapter 4.3 System The System tab window is for some basic settings of the adapter. On this tab window, you can upgrade the firmware to the latest version, reset the adapter’s settings to the factory defaults and configure all adapters’... -
Page 24: Reset Device
The parameter information of PIB will restore to the factory defaults after resetting the PLC. To upgrade the device's firmware, follow these instructions: Download PIB file and firmware upgrade file from the TP-LINK website www.tp-link.com). Enter the path name or click to select the downloaded files on the computer into the corresponding blanks. - Page 25 TL-PA2010 AV200 Nano Powerline Adapter appear on the Network configuration homepage whose Device’s Password had been entered for the same logical network. A dialog window will appear to report the success of this operation. All Powerline devices are shipped using a default logical network (network name), which is normally “HomePlugAV”.
-
Page 26: Chapter 5 Advanced Feature: How To Use The Pair Buttons
TL-PA2010 AV200 Nano Powerline Adapter Chapter 5 Advanced Feature: How to Use the Pair Buttons 5.1 Pair ( Secure with 128 bits-AES) The Homeplug AV standard uses 128-bit AES (Advanced Encryption Standard) to safely transmit data between powerline adapters. For the powerline adapters to communicate with each other they all need to use the same Network Membership Key (NMK). -
Page 27: Join/Leave Existing Powerline Av Network
TL-PA2010 AV200 Nano Powerline Adapter Join an existing Powerline AV Network: Powerline adapter A and Powerline adapter B form a HomeplugAV Network, Powerline adapter C wants to join this network. Step 1. Press and hold the Pair button on Powerline adapter C for 1 second. -
Page 28: Appendix A: Troubleshooting
TL-PA2010 AV200 Nano Powerline Adapter Appendix A: Troubleshooting The Troubleshooting provides answers to common problems regarding the Powerline Adapter. 1. The Power LED does not light up. Ans. Check the following: a) Make sure that the Powerline Adapter is properly plugged into a power outlet.