American Standard Chandler Front Apron (w/Recess for Tile) Double Bowl Sink 7048.301 Specification Sheet

CHANDLER™ FRONT APRON (w/Recess for Tile)
DOUBLE BOWL KITCHEN SINK
• Dupont Corian surface
®
• Double bowl design
• Front apron panel - recessed for tile
• Top mount
• Shown with 4771.702 Hampton faucet with
porcelain cross handles (not included)
• Silicone sealant supplied
• Available in center hole only, 3, or 4 faucet
hole configuration
❏ 7048.301 Center hole only
❏
7048.303 3 hole
❏
7048.304 4 hole
Nominal Dimensions:
914 x 559 x 254mm
(36" x 22" x 10-1/2")
Bowl sizes:
Right Hand: 359mm (14-1/8") wide
16-1/4" (413mm) front to back
203mm (8") deep
Left Hand: 432mm (17") wide
476mm (18-3/4") front to back
254mm (10") deep
Compliance Certifications -
Meets or Exceeds the Following Specifications:
• ANSI Z124.6 for Non-Metallic Sinks
To Be Specified:
❏ Color:
❏ Faucet*:
❏ Faucet Finish:
❏ Basket Strainer: 4331.013
❏ Soap Dispenser: 4503.115, Color:
❏ Traps:
* See faucet section for available models
© 2008 AS America Inc.
CHANDLER™ FRONT APRON
(w/Recess for Tile) DOUBLE BOWL SINK
7-1/8"
(181mm)
8-3/4"
(222mm)
CABINET
FASCIA
2" (51mm)
FRONT OF
APRON
TILE RECESS AREA
6-3/16" x 24-1/2" x 3/8"
(157 x 822 x 10mm DEEP)
Y
257mm
248mm
(10-1/8")
(9-3/4")
146mm
(5-3/4")
NOTES:
*
FOR COUNTERTOP CUTOUT SEE INSTALLATION INSTRUCTIONS
SUPPLIED WITH SINK.
TILE RECESS AREA DESIGNED FOR FOUR (4) 6" x 6" x 5/16" THICK
CERAMIC TILES. TILES NOT INCLUDED. BE SURE TO USE TILES
THAT FIT RECESS.
FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.
PROVIDE SUITABLE REINFORCEMENT FOR ALL WALL AND
COUNTERTOP SUPPORTS.
IMPORTANT: Dimensions of fixtures are nominal and may vary within the
range of tolerances established by ANSI Standard Z124.6
These measurements are subject to change or cancellation. No responsibility
is assumed for use of superseded or voided leaflet.
G13
7048.301
1 HOLE
VARIATION
HOT
COLD
4"
18" (102mm)
(457mm)
2-3/4"
1-3/8" (35mm) DIA.
(108mm)
HOLES TYP.
C/L
1" (25mm) 4-1/2" 9-1/2"
RAD. TYP. (114mm) (241mm)
36"
(914mm)
DUPONT CORIAN
®
FINISHED WALL OR
SPLASH BACK
4"
2"
(102mm)
(51mm) OPTIONAL
SPRAY
4"
1-3/4"
(102mm)
(44mm) DIA.
7048.304
11"
4 HOLE
(279mm)
VARIATION
7048.303
3 HOLE
VARIATION
3-1/2"
(89mm) DIA.
22"
*
(559mm)
CUTOUT
NOTE
1-1/2" REF.
(38mm)
SEALING
COMPOUND
COUNTERTOP
3/8"
(BY OTHERS)
(10mm)
8-1/8"
(206mm)
5-3/4"
(146mm)
36" (914mm)
SUGGESTED
(2) 1-1/2" O.D.
TAILPIECE
FINISHED
FLOOR
Revised 6/06